The horizontal distance from a tower, mast, or antenna to the nearest
power line should be at least twice the total length of the combined
mast and antenna. This will ensure that the mast will not contact
power if it falls during or after installation.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT
HEIGHTS ABOVE GROUND
• Select equipment locations that will allow safe, simple equipment
installation.
• Do not work alone. A friend or co-worker nearby is important when
dealing with electrical equipment.
• Do not erect antennas or towers on windy days.
• Only use approved non-conducting ladders and other safety
equipment.
• If a tower or mast begins falling, do not attempt to catch it—stand
back and let it fall.
• If any piece of equipment comes into contact with a power line, DO
NOT TOUCH IT OR ATTEMPT TO MOVE IT — call your local power
company.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED
AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE
LIGHTNING ARRESTORS
This will help prevent fire damage or human injury in case of lightning,
static build-up, or short-circuit within equipment connected to the
antenna.
• The base of the antenna/mast or tower must be connected directly
to the building’s grounding rod or to one or more approved
grounding rods using 1 OAWG ground wire and corrosion-resistant
connectors.
• Refer to the National Electrical Code for grounding details.
• Lightning arrestors for antenna feed coaxial cables are available
from your local hardware store.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER:
• DO NOT TOUCH THE PERSON—Use a non-conductive dry board,
stick, or rope to push or drag them so they are no longer in contact
with the electrical source.
• Once the person is no longer in contact with the electrical power,
call an ambulance.
Safety Precautions
Carefully observe these instructions and any special
instructions that are included with the equipment
you are installing.
CONTACT WITH POWER LINES IS EXTREMELY
DANGEROUS
Make sure there will be no possible contact
with any power lines. Assume all overhead lines
are power lines. Ensure no antennas, masts,
towers, guide wires, or cables may fall and make
contact with power lines during installation.
Assembling the antenna:
1. Assemble the aluminum tube clamps and U-bolts (see figure A). Insert
the aluminum tube through the aluminum tube clamp (see figure B).
2. Feed the antenna extension cable through the bottom of the aluminum
tube. Screw onto the bottom of the omni-directional antenna (see
figure C).
3. Connect the omni-directional antenna into the aluminum tube and
fasten with screw and spring washer (see figure D).
4. Mount the completed omni-directional antenna to a mast (not included)
and fasten to your desired mounting location (roof, deck, fence, etc.).
5. Connect the other end of the extension cable to a wireless receiver.
Installing the Antenna
ACCANT08_QSG_EN_R1
Package contents:
1. Nut (×4)
2. Spring Washer (×5)
3. Aluminum Tube Clamp (×2)
4. Mast (not included—optional for
installation)
5. U-Bolt (×2)
6. Aluminum Tube
7. Screw (×3)
8. Omni-Directional Antenna
9. 20ft (6m) Antenna Extension
Cable
ATTENTION:
• Review the Installation Tips prior to assembling and installing the
antenna. Following the installation tips is necessary to ensure
effective signal strength.
•
Select a mounting location (roof, fence, etc.) prior to assembling the
antenna. Mast (not included) might be required for proper mounting
depending on your specific installation.
IMPORTANT:
Examine the site prior to beginning any installation and anticipate the
following potential hazards.
Compatibility
Prior to installing the antenna, visit
lorextechnology.com/compatibility and review the Wireless
Range Extender Antennas Compatibility chart.
NOTE: Newer wireless receivers may include weatherproof housing
and can be installed outdoors. See the product specifications to
determine the weatherproof rating of your receiver.
1
2
3
48
5
6
7
9
Figure A
Figure B Figure C Figure D
Roof with Mast Fence
NOTE: You can use the Omni-
Directional Antenna along with a
Directional Panel Antenna (Lorex
model: ACCANTD9) to increase the
range of a specific camera. Connect
the Directional Panel Antenna directly
to the camera. A clear line of sight
is highly recommended in order to
maximize signal strength. Visit
lorextechnology.com for more details.
Installation Tips
The antenna can be installed in several locations, such as a roof, fence,
deck, or the side of your house. Using a mast for installation is optional. Use
a mast if necessary to achieve a clear line of sight between the antenna and
the wireless cameras.
NOTE: Consult your local hardware store about what type of mast would be
suitable for your particular installation.
• The antenna has a 360° horizontal signal pattern and a 10° vertical signal
pattern (see diagram below).
• The highest signal strength is located within 10° of the middle of the
antenna. Cameras located above or below the middle of the antenna may
recieve poor or no wireless signal.
• A clear line of sight between the middle of the antenna and the wireless
camera(s) is necessary to ensure effective signal strength (estimated
range up to 800ft).
• Objects such as concrete, cement, trees, or other large objects
can reduce the strength of your wireless signal.
Directional Panel Antenna
(Lorex model: ACCANTD9)
360°
10°
ATTENTION:
Prior to installing your antenna, review the online antenna FAQ by visiting
lorextechnology.com and searching for ACCANT08. Read the antenna FAQ
to ensure you have the correct antenna and installation method to meet
your needs.
