LOUVERS LED ADV-4-2-LED-48W User manual

Installation Instructions
LOUVERS
LED
DIVISION OF LOUVERS INTERNATIONAL
ADVANTAGE LED
PLEASE READ ALL INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. REPLACE ANY CRACKED OR DAMAGED
PROTECTIVE SHIELDS AND ITEMS. THIS FIXTURE MUST BE ASSEMBLED AND INSTALLED BY A QUALIFIED ELECTRICIAN.
MODEL RATED VOLTAGE RATED WATTAGE DRIVER TYPE PROTECTION
ADV-4-2-LED-48W AC 120-277V, 50-60 Hz Max. 48W Class 2 IP65
ADV-8-2-LED-96W AC 120-277V, 50-60 Hz Max. 96W Class 2 IP65
Technical Data:
Safety Instructions:
1. REMEMBER: This xture MUST be installed by a qualied electrician.
2. Disconnect the existing lamp from the power supply prior to installation. Let the lamp cool down before replacing the luminaire.
3. DO NOT TOUCH the LED lamp with your bare hands prior to or during installation.
4. Replace the lamp cover if it is broken, cracked or damaged in any way. Never use the xture without the lamp cover in place.
5. In case of damage, disconnect the lamp from the power supply. DO NOT try to repair the lamp on your own. Repairs must be done by a
qualied electrician or factory service.
6. Please refrain from looking directly into the light source.
7. Please connect xture with Awg 18 type SJ or SJT grounded cord-set rated minimum 60C.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT.
POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA FENTE LA PLUS LARGE.
8. Please make sure the ground wire has been connected before turning on the switch.
Installation:
1. Position the cable gland into the line hole in the base.
Through Wire Only
ø 0.827 in.
X 2
2. Assemble the clips into the designated position.
“CLICK”
3. Fix the two ends of the cover and base rst.
“CLICK”
Louvers International 851 N. Church Court, Elmhurst, Illinois 60126 │ P: 800.543.3765 │ F: 800.568.8377 www.louversintl.com 8/28/15
Page 1 of 3

Installation (Continued):
Installation Instructions
ADVANTAGE LED
4. Drill the mounting holes at the place of installation (i.e. shelf / ceiling). Make sure that no cables or other lines are concealed in the area
of drilling.
5. Insert the suitable installation cable through the washer in the hole. (The washer can be moved into the desired position by slightly pulling.)
Connect the cable end with the saddle at the connecting plate. Pay attention to the correct polarity.
6. Fix the LED light plate onto the base.
Louvers International 851 N. Church Court, Elmhurst, Illinois 60126 │ P: 800.543.3765 │ F: 800.568.8377 www.louversintl.com Page 2 of 3
Chain Support Arm
M5/M6 X 2
Chain Support Arm
Mounting Bracket
Housing Bracket
Standard
3.7 ft - lb min
H05/H07 RN-F
#18 - 3 / #16 - 3
0.4 inch min.
approx. 6 in.
0.314 - 0.47 in.

Installation (Continued):
Installation Instructions
ADVANTAGE LED
7. Put on the cover and fasten with the clips. All clips should be used.
Louvers International 851 N. Church Court, Elmhurst, Illinois 60126 │ P: 800.543.3765 │ F: 800.568.8377 www.louversintl.com 8/28/15
Page 3 of 3
Please follow local regulations regarding recycling of existing xtures. Remember, old xtures contain valuable materials and may contain hazardous
materials such as mercury. They should be sent to the appropriate recycling facility.
Do not cause unnecessary harm to the environment and human health through uncontrolled waste disposal. Please dispose of old equipment at
the appropriate recycling facility.