LOWE'S LGCF1602 User manual

󾋼.󾋻'×󾋺.󾋾' Tool Storage Shed
ASSEMBLY MANUAL
MODEL#: LGCF1602

Use bolts to secure the frame to the ground to against the strong wind.
！

1660mm (65.35’’)
1792mm (70.55’’) 1602mm (63.07’’)
914mm (36’’)
1580mm (62.2’’)
1125mm (44.3’’)
1635mm (64.37’’)
1792mm (70.55’’)
955mm (37.6’’)
The manual will assist you during the whole process of assembling.
Make sure you have all the parts & hardware as list 1 and list 2 shown;
Prepare the level ground for installation.

1602-list 1

Flat head screw
1602-list 2

You need to prepare bolts by yourself to secure the
frame to the ground.
Insert the part#A and fasten with
screws 1# and gaskets.
1. Attach part #A to part #A1/A2/A3 as the instruction by f ixing. (Attention: four corners
MUST been right angles and check if the two diagonal distance of square is equal by tape
measure).
2. Fix the part #C3 on the part #A1.
Fix the part#C3 by using screws 9# and gaskets.

02
Plastic Gaskets
Steel Gaskets
2 Steel Gaskets
1. Install part #C/J2/C1 with screws 2#, gaskets and nuts as shown in ①.
2. Place the assembled wall (C/J2/C1) on the bottom frame(A1), using 3
screws 1# and gaskets to f ix.
Attention:
To ensure the stability of
the wall panel(J2) during assembly,
you can temporarily reinforce this
position(☆) with screws 2#, and
replace it with other correct screws
when the next installation is made.
Section View Section View

1# 1#
1#
03
Plastic Gasket
Plastic Gasket
1. Place part #J/C/J2 on the bottom frame(A2/A3), using 5
screws 1# and gaskets to f ix.
2. Install 2 part #H1 with 4 screws 9# and gaskets, then put
on the plastic caps as shown in ① ③/② ④.
Back Side
Repeat the above procedures to assemble the another side.
Front Side
3. Install 2 part #H with 4 screws 9# and gaskets, then put on the plastic caps as shown in ③④.

04
Plastic Gasket
Plastic Gasket
Plastic caps
Plastic caps
Repeat the above procedures to assemble 2 part #J on Side Wall.
1. Install 2 part #J (Back Wall Panel): Use 7 screws 1# and gaskets to f ix them on
the bottom frame.
2. Fix 2 part #J (Back Wall Panel) to part #H with 6 screws 9# and gaskets, then put
on the plastic caps.
Before After

1.Enclose with part #B1/B2/B3 according to the f igure above,
and the part #B connects the four corners, then f i xed with 16 screws 12#
and gaskets as shown in ① ②.
2.Use 4 screws 9# and gaskets to fix 2 part #C4 on part #B1 as shown in ③ ④.
3.Fix the part #B4 & B8 on the inside of part #B1 with 2 screws 12# and gasket as shown in ⑤.
!
Plastic Gasket
Plastic Gasket
Front Side
Back Side
05

1. Place the assembled beam (B1, B2, B3) on the upper end of the wall panel, and f ix with
35 screws 1# and gaskets as shown in ①②.
2. Fix the part #C4 to the upper end of part #C1(C2) with 4 screws 3#, 8 gaskets and 4 nuts,
(the gaskets and nuts are on the back side as shown in ③④).
06
Plastic Gasket
2 Steel Gasket
Inside View Inside View

07
Assemble the top frame:
Use 2 screws 15# and nuts to combine Part E with Part D1 as shown in ①.
Use 2 screws 15# and nuts to combine Part E with Part D2 as shown in ②.

08
Put the top frame on beam(B3/B1/B3), f ix it with 17 screws1# and gaskets.
Cross screwdriver
Plastic Geskets
Install Top Frame

The section view of how to place part #G1/G2 on part #K1/K3.
Assemble the part #G1 to the one side of part #K1 with 3 screws 2#, gaskets and nuts.
Assemble the part #G2 to the one side of part #K3 with 3 screws 2#, gaskets and nuts.
09
Steel Gasket

6
Steel Gasket
10
The roof panel part #K1/K2/K2/K2/K3 is laid in order as shown.
Use 6 screws 2#, gaskets and nuts to fix the roof panel K1/K3 on top frame
D1/D2 as shown in ①.
D1
D2

Side View
2 Holes
Back Side
Front Side
Use 12 screws 2#, gaskets and nuts to f ix the roof panel K1/K2/K2/K2/K3 on top frame E as shown in ②.
Use 12 screws 1#, gaskets to f ix the roof panel K1/K2/K2/K2/K3 on the back side beam B2.
②
E
Plastic Gasket
Steel Gasket

Part #G7 is used to cover the gap
between part #G3 and part #G4
2 Holes
1. Use 24 screws 2# to install part #G3/G4 on both ends of the roof first（Note: Please follow the installation
position as shown in the picture）.
2.Install part #G7 at the joint of part #G3/G4,
and f ix it with 8 screws 2#, gaskets and nuts as
shown in ③.
3.Part #G5/G6 is inlaid at the four corners and f ixed with 8 screws 3#,16 gaskets and 8 nuts as shown in ①②.
Steel Gaskets 2 Steel Gaskets
12

Flat Head Screws
The front side of the left door The back side of the left door
Steel Gaskets

Steel Gaskets
13-M-2
The front side of the right door The back side of the right door
Flat Head Screws