Loxit Tabcart 16 User manual

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
Charge/ USB Charge 7430 and 7431
Tabcart 16 instructions-
1. Unlock and open the storage compartment.
2. A. Unfasten the charge compartment hatch by removing the two M5 bolts indicated
B. Open the hatch to around 45 degrees and unhook the hatch from the trolley.
3. A. Pass your devices charging cable
through the grommet from the inside.
B. Adjust the length as needed to reach
your device, then loop the cable through
the restraint.
Repeat steps A and B until all cables are
in place.
A.
B.
A.
B.

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
4. Plug the charging cables into the USB charger units or the
power strips, depending on your Tabcart version.
6. Power input is located on
the underside of the trolley.
5. A. Hook the hatch removed in step 2 back into position
B. Secure the hatch in place using the two M5 bolts removed in step 2.
B.
A.

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
WARNING
This equipment is not a toy.
Children must be under surveillance to ensure that they do not play with this piece of electrical
equipment.
The product is shipped fully assembled, if the unit is being stored do not double stack.
Ensure that all casters are released from their brakes and are running freely when being moved.
This unit is not designed for rough terrain.
Please treat sympathetically avoiding kerbs or changes in level and being especially careful when
changing floor surfaces or crossing sloping areas. Take your time. If in doubt ask a second person
to assist you.
Maintenance Instructions
There are no user maintenance or adjustment points on this machine. Simply clean dust and dirt
from the outside of the unit and inspect for damage or breaks.
Cleaners and disinfectants must not be highly alkaline or acidic.
The user should visually check the equipment for signs of wear or misuse before each time of
using and for the security of the screen or any accessories.
The condition of electrical cables and plugs should be checked for wear or abrasion before use.
In addition, the equipment should be visually inspected in more detail every three months to
ensure that the unit is functioning properly and if it is not the user should report this to the
manufacturer for advice or for the return of the unit to base for repair.
Incidences of misuse must be reported immediately and the unit placed out of commission.
All repairs to the unit must only be carried out by Loxit.
The warranty is only valid in so far as the equipment has been used and maintained correctly
and has not been tampered with.
Violent treatment will invalidate the warranty.
During operation if the unit makes any unusual noises or smells turn off the power supply at the
mains immediately.
Ambient temperature range +5deg C to +40 deg C.
Safety
Before Charging Please Check:
1. The wall socket is switched on
2. The RESET button on the RCD is pushed in
3. The red neon indicator switch on the power strip is switched on and lit if applicable, or the rocker
switch in the case of ChargeConnect products.
4. The IEC lead is plugged into the IEC inlet and the IEC Inlet switch is turned on with the neon indicator
light illuminated.
5. The low voltage power leads are firmly connected to the power source (device transformer or
ChargeConnect) and the device.

Loxit Limited, First Avenue, Poynton Industrial Estate, Poynton, Cheshire, UK. SK12 1YJ
www.loxit.com ꞁ [email protected]m ꞁ [phone]
TabCart products must be connected to an RCD protected earthed mains supply when charging.
Power Rating:
230v –50 Hz –13 amps. TOTAL NOT TO EXCEED 10 amps. OUTPUT –230V AC –10 amps.
There are no user serviceable parts within the unit, any warranty and service issues should be referred
to your supplier.
In the event of the mains plug or lead being damaged, the unit should not be used until a new plug or
lead has been fitted by a competent person. The old plug or lead must be safely disposed of.
Operation:
THE MAINS INPUT TO THE TABCART TROLLEY MUST ONLY BE PLUGGED INTO AND REMOVED FROM A
SWITCHED MAINS PLUG SOCKET WHICH IS TURNED OFF.
Please ensure the mains input cable is unplugged before unlocking the wheels (if applicable) and moving
the trolley.
DO NOT DROP THE RCD PLUG, it contains sensitive electronics and may become damaged.
Mains input cables must be inspected daily for damage and wear.
If any fault or damage is found with any mains input cable, remove all power sources and stop using
immediately. Contact Loxit Limited on [phone] for a replacement cable.
Visit www.loxit.com for contact details or sal[email protected]m to e-mail.
UNDER NO CIRCUMSTANCES SHOULD REPAIRS BE MADE TO THE MAINS INPUT CABLE.
This tablet PC storage and charging product must only be used by a competent adult and must
not be used if this can not be assured.
If you are in any doubt please refer to your Health and Safety Co-ordinator and/or Health and
Safety Manual for guidance.
This product requires PAT testing at maximum 12 monthly intervals.
Portable Appliance Testing This unit must only be earth bond and insulation tested using the IT
settings on any PAT tester.
WEEE Directive When the unit becomes redundant it must be disposed of in compliance with
the WEEE directive 2005.