LSC GenVI Series User manual

12 Channel Rack Mount
6 Channel Rack Mount
12 Channel Wall Mount
6 Channel Wall Mount
12 Channel Wall Mount
Hardwired
6 Channel Wall Mount
Hardwired
GenVI
Advanced Dimming and Power
Switching System
User Manual
LSC Control Systems ©
[phone]
[email protected].au
www.lsccontrol.com.au
V4.02
August 2022

Gen VI Dimmer
User Manual
Page 2
Disclaimer
LSC Control Systems Pty Ltd has a corporate policy of continuous improvement, covering areas
such as product design and documentation. To achieve this goal, we undertake to release
software updates for all products on a regular basis. In light of this policy, some detail contained
in this manual may not match the exact operation of your product. Information contained in this
manual is subject to change without notice.
In any event, LSC Control Systems Pty Ltd cannot be held liable for any direct, indirect, special,
incidental, or consequential damages or loss whatsoever (including, without limitation, damages
for loss of profits, business interruption, or other pecuniary loss) arising out of the use or the
inability to use this product for its intended purpose as expressed by the manufacturer and in
conjunction with this manual.
Servicing of this product is recommended to be carried out by LSC Control Systems Pty Ltd or
its authorised service agents. No liability will be accepted whatsoever for any loss or damage
caused by service, maintenance or repair by unauthorised personnel.
In addition, servicing by unauthorised personnel may void your warranty.
LSC Control Systems’ products must only be used for the purpose for which they were intended.
Whilst every care is taken in the preparation of this manual, LSC Control Systems takes no
responsibility for any errors or omissions.
Copyright Notices
GEN VI dimmers are developed by LSC Control Systems Pty. Ltd.
“LSC Control Systems” is a registered trademark.
lsccontrol.com.au is owned and operated by LSC Control Systems Pty Ltd.
All Trademarks referred to in this manual are the registered names of their respective owners.
The operating software of the GEN VI and the contents of this manual are copyright of LSC
Control Systems Pty Ltd © 2016.
All rights reserved.
Contact Details
LSC Control Systems Pty Ltd
ABN 21 090 801 675
65-67 Discovery Road
Dandenong South, Victoria 3175 Australia
Tel: [phone]
email: [e-mail]
web: www.lsccontrol.com.au

Gen VI Dimmer
User Manual
Page 3
Contents
1Introduction................................................................................................6
1.1 About this Manual.......................................................................................................6
1.1.1 Conventions Used in this Manual ........................................................................6
1.2 Overview ....................................................................................................................6
1.2.1 Features..............................................................................................................6
1.2.2 GEN·VI Control Philosophy.................................................................................7
2Quick Start Guide .......................................................................................8
2.1 DMX Address.............................................................................................................8
2.2 Channel Modes ..........................................................................................................8
2.2.1 Dimmer or TruPower (Switch)..............................................................................8
2.2.2 Auto Power..........................................................................................................9
3Models ......................................................................................................10
3.1 Front Panels.............................................................................................................10
3.1.1 Rackmount GEN·VI...........................................................................................10
3.1.2 Wallmount GEN·VI............................................................................................10
3.2 100-120VAC Input Power.........................................................................................11
3.3 Output Connectors ...................................................................................................11
4Installation ...............................................................................................12
4.1 Safety.......................................................................................................................12
4.2 Unpacking ................................................................................................................12
4.3 Installation................................................................................................................12
4.3.1 Rackmount GEN·VI...........................................................................................12
4.3.2 Wall-mount GEN·VI...........................................................................................12
4.3.3 Patch Bay Installation........................................................................................14
4.4 Connections .............................................................................................................15
4.4.1 Input Power Supply ...........................................................................................15
4.4.2 Wallmount GEN·VI Power Input ........................................................................15
4.4.3 DMX512 Connections........................................................................................15
5Configuration and Operation ....................................................................16
5.1 Overview ..................................................................................................................16
5.2 Help Screens............................................................................................................16
5.3 Home Pages.............................................................................................................16
5.3.1 DMX Address Home Page.................................................................................16
5.3.2 DMX Address....................................................................................................17
5.3.3 Dimmer Output Home Page ..............................................................................17
5.3.4 Status................................................................................................................18
5.3.5 Owner................................................................................................................18

Gen VI Dimmer
User Manual
Page 4
5.4 Dimmer Status..........................................................................................................19
5.5 Riggers Control.........................................................................................................20
5.5.1 Chaser...............................................................................................................20
5.6 Config Menu.............................................................................................................21
5.7 Dimmer or Trupower (Switch)...................................................................................21
5.8 DMX Menu ...............................................................................................................22
5.8.1 Patch.................................................................................................................23
5.8.2 16 Bit DMX Control............................................................................................24
5.8.3 DMX Loss Memory............................................................................................24
5.8.4 Auto Power Enable and Hold Time....................................................................27
5.8.5 Auto Power Mode..............................................................................................28
5.8.6 View Input..........................................................................................................29
5.9 Set DMX Term..........................................................................................................29
5.10 Channels Menu ........................................................................................................29
5.10.1 Min Level...........................................................................................................31
5.10.2 Max Level..........................................................................................................31
5.10.3 Curve.................................................................................................................31
5.10.4 Source (DMX or Auto Power) ............................................................................33
5.11 Colour Theme Menu.................................................................................................33
5.12 System Menu ...........................................................................................................33
5.12.1 Code (Software) Upgrade..................................................................................34
5.12.2 Reset.................................................................................................................34
5.12.3 Fan Control........................................................................................................34
5.12.4 Import Export.....................................................................................................35
5.13 Lock / Unlock............................................................................................................35
6Alarms and Troubleshooting ....................................................................37
6.1 Maintenance.............................................................................................................37
6.2 Alarms......................................................................................................................37
6.3 Trouble Shooting......................................................................................................38
6.3.1 Rigger Test........................................................................................................38
6.3.2 DMX Control......................................................................................................38
7HOUSTON X..............................................................................................39
8DMX Explained .........................................................................................40
8.1 Overview ..................................................................................................................40
8.2 Typical DMX Installations .........................................................................................40
9RDM ..........................................................................................................41
9.1 Overview ..................................................................................................................41
9.2 GEN·VI RDM............................................................................................................41
10 PTFD Explained .....................................................................................42

Gen VI Dimmer
User Manual
Page 5
10.1 Overview ..................................................................................................................42
10.2 What is PTFD?.........................................................................................................42
10.3 Opto-isolated Problems............................................................................................42
10.4 Hard Firing................................................................................................................42
10.5 The Proof..................................................................................................................43
11 Specifications and Output Options .......................................................44
11.1 Rackmount GEN·VI..................................................................................................44
11.2 Wallmount Gen VI ....................................................................................................45
11.3 Socapex Pinouts.......................................................................................................46
11.4 Harting/Wieland Pinouts...........................................................................................47
12 Feature History......................................................................................47
13 Compliance Statements ........................................................................49

Gen VI Dimmer
User Manual
Page 6
1Introduction
1.1 About this Manual
This manual describes the installation, configuration and operation of the GEN·VI range of advanced
dimmer/power systems manufactured by LSC Control Systems:
•GEN·VI Rackmount
•GEN·VI Wallmount
There are four different colour themes that you can select on the GEN·VI touch screen. The screen
images in this manual use the default “Gothic” colour theme and a 12-channel model.
1.1.1 Conventions Used in this Manual
Throughout this manual, certain conventions have been used to make the meaning clearer.
•A word in Bold text represents a button on the touch screen
•Emphasis is indicated by underlining
•Notes or Hints are displayed in italic font
1.2 Overview
The GEN·VI dimmers can be controlled by any DMX512 lighting controller. Dimmer configuration,
patching and local control is achieved via a backlit colour touch screen on the front panel. A lock
code can be used to prevent unauthorised tampering. Most control functions, configuration options
and front panel operations can also be remotely controlled using the RDM (Remote Device
Management) protocol. System configuration, monitoring and logging is also possible via LSC’s
HOUSTON X software.
1.2.1 Features
•DMX512 (1990), DMX512-A (E1-11) and RDM (E1-20) compliant control.
•If DMX is lost, the GEN·VI can either hold the last values or fade to a “DMX Loss memory”
after a programmable delay.
•RCBO (Residual Current Breaker with Overcurrent) per channel. This is a combined overload
circuit breaker with earth leakage (RCD/GFI) protection and Neutral Disconnect function for
each circuit.
•Individual dimmer channel settings for:
oDMX address patching.
oMinimum and maximum output levels.
oChoice of three fade curves (linear, s, or custom) or LSC TruPower (switched) power
output.
•LSC TruPower (switchedpower) providesdirect poweroutput by utilising relays guaranteeing
there are absolutely no electronics in the circuit to interfere with connected loads. Ideal for
discharge lamps and LEDs.
•LSC’s proprietary Current Control Technology © (CCT) protects all RCBO’s from nuisance
tripping due to cold lamp inrush currents.
•GEN·VI Rackmount has either 10, 16 or 25 amps per channel models with a choice of rear
output connectors.
•GEN·VI Wallmount has either 10 or 25 amps per channel models with a choice of front output
connectors or internal output terminals.
•Settable constant fan speed or fully automatic.
•16 bit internal architecture which gives smooth fades. Essential when dimming LEDs.
•16 bit DMX control selectable for super smooth fades.
•Pulse transformers fired dimmers will dim most types of loads. See section 10.
•100% duty cycle operation across all channels simultaneously.
•CE and C tick approved.

Gen VI Dimmer
User Manual
Page 7
1.2.2 GEN·VI Control Philosophy
Each channel can be independently set to dim mode (with a selection of standard dimming curves
in either 8-bit or 16-bit accuracy) or relay mode (TruPower) for direct power switching.
The control source for each channel can be either,
DMX Only. Channels configured for “DMX Only” are controlled by the DMX slot to which they
have been patched. If the DMX signal fails, the channels can either hold their last state or
after a programmable delay time, fade to a “DMX Loss Memory” previously stored in the
GEN·VI.
Every DMX controlled channel can be set to be either a dimmer or a “Trupower” switch.When
set to Trupower,
•The channel will switch ON when the DMX signal exceeds 60%.
•The channel will switch OFF when the DMX signal drops below 40%
Auto Power. Channels configured for “Auto Power” are switched on when the lighting
console is turned on and a valid DMX signal is detected on the input to the GEN·VI,
regardless of actual DMX levels. Therefore, the lighting, audio and video equipment
connected to these channels will be powered up without user intervention. When the console
is turned off, the equipment will remain on for a programmable “hold time” and then be
automatically switched off. This means there is less chance of some equipment being
accidentally left on when not in use, ensuring the maximum service life and a lower power
bill.
Global control of “Auto Power” can be enabled/disabled.
See section 2 “Quick Start Guide” for details on how to change channel modes.
Channels can also be controlled from the touch screen by selecting Riggers Control. See section
5.5.

Gen VI Dimmer
User Manual
Page 8
2Quick Start Guide
2.1 DMX Address
To patch all of the channels in one GEN·VI rack to sequential DMX slots use the View Mode button
to select the “DMX Address” home page.
Press DMX Address.
Enter the DMX address for the first channel in this GEN·VI then press Apply. All channels will be
patched to sequential DMX slots.
Note: GEN VI channels can be individually patched to any DMX slot. See section 5.8.1.
2.2 Channel Modes
Each GEN·VI channel can be configured to be either,
•A DMX controlled dimmer
•A DMX controlled switch (TruPower)
•An “Auto Power” switch (turns on when a DMX signal is present)
2.2.1 Dimmer or TruPower (Switch)
Channels set to Dimmer or TruPower (Switch) are controlled by the DMX level of the DMX slot to
which they are patched.
A channel set to TruPower (switch) will switch ON when its DMX signal exceeds 60% and switch
OFF when its DMX signal drops below 40%.
To set a channel to be a dimmer or a switch, from either home screen select Config, Dim/TruPower.
Dimmer mode.
Light grey
TruPower mode.
Dark grey
Legend
DMX slot of
first channel
DMX slot of
last channel
View
Mode
DMX
Address

Gen VI Dimmer
User Manual
Page 9
Press a channel number to toggle its mode between “Dimmer” mode and “TruPower” (switch) mode.
A light grey button indicates dimmer mode and a dark grey button indicates TruPower mode as
shown in the “Legend”.
Configure your channels then press Save.
Note: Changing a channel from TruPower to Dimming mode can potentially damage connected
equipment that should not be connected to a dimmed output. If you change a channel from TruPower
to Dimming you will be asked to Confirm your changes.
2.2.2 Auto Power
Channels configured for “Auto Power” are switched on when a valid DMX signal is detected on the
input to the GEN·VI, regardless of actual DMX levels. When the DMX signal ceases, the channels
will switch off after a user programmed time.
“Auto Power” can only be selected if the channel is set to “TruPower” mode. See above.
To set a channel to “Auto Power” mode, select Config, Channels, select the channel number(s)
then select Edit and use the “Parameter Selector” buttons to select the “Source”parameter.
Once “Source” is selected, the choose Auto Power then select Apply.
Control of all “Auto Power” channels can be disabled or enabled.
From either home screen press Config, DMX.
In the “Auto Power” pane press Disable. When disabled, the button becomes Enable.
Press Hold Time to set the time that the “Auto Power” channels will stay ON after the DMX signal is
lost.
Parameter
Selector
Parameter
Selector
“Source” Parameter
Auto
Power

Gen VI Dimmer
User Manual
Page 10
3Models
The GEN·VI rackmount is available in the following models,
•12 channels at 10 amps per channel.
•12 channels at 16 amps per channel. Not available for sale in Australia or New Zealand.
•6 channels at 25 amps per channel.
The GEN·VI wallmount is available in the following models,
•12 channels at 10 amps per channel.
•6 channels at 25 amps per channel.
3.1 Front Panels
3.1.1 Rackmount GEN·VI
The front panel contains the DMX input and through connectors, load RCBO’s (Residual Current
Breaker (RCD/GFI) with Overcurrent and Neutral disconnect), SD card slot (used for software
upgrades) and LCD touch screen.
Do not use sharp objects to operate the touch screen!
12 Channel GEN·VI Rackmount
3.1.2 Wallmount GEN·VI
The front panel contains load RCBO’s (Residual Current Breaker (RCD/GFI) with Overcurrent and
Neutral disconnect), LCD touch screen. The DMX connectors and SD card slot are located on the
side of the unit.
12 Channel GEN·VI Wallmount with front outlets
SD Card slot
Touch screen
RCBO Output Breakers
DMX Input
DMX Thru
Touch screen
RCBO Output Breakers
SD Card slot
DMX Input
Output
connectors
DMX Thru