LSI 620J User manual

CTS2600, 620j, and 630j Branding
Guide
48321-00, Rev A
July 2010

LSI and the LSI logo are trademarks or registered trademarks of LSI Corporation or its subsidiaries. All other brand and product names may be trademarks of their respective companies.
!LIST ANY OTHER REQUIRED TRADEMARKS! REMOVE THIS STATEMENT!
This preliminary document describes a preproduction product and contains information that may change substantially for any final commercial release of the product. LSI Corporation makes no express
or implied representation or warranty as to the accuracy, quality, or completeness of information contained in this document, and neither the release of this document nor any information included in it
obligates LSI Corporation to make a commercial release of the product. LSI Corporation reserves the right to make changes to the product(s) or information disclosed herein at any time without notice.
LSI Corporation does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by LSI Corporation;
nor does the purchase, lease, or use of a product or service from LSI Corporation convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual property rights
of LSI Corporation or of third parties.
FOR ALL DOCUMENTS UNDER NDA INCLUDE THE PARAGRAPH BELOW: REMOVE THIS RED TEXT
This document contains proprietary information of LSI Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of
LSI Corporation.
FOR INTERNAL DOCUMENTS INCLUDE THE PARAGRAPH BELOW: REMOVE THIS RED TEXT
This document contains proprietary information of LSI Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of
LSI Corporation.
Corporate Headquarters Email Website
Milpitas, CA [email protected] www.lsi.com
800-372-2447
Document Number: 4831-00, Rev A
Revision History
Version and Date Description of Changes
Rev A Initial Document

LSI Corporation Confidential | July 2010 Page 3
LSI 2600, LSI 620j. and LSI 630j Branding Guide Overview of the CTS2600, 620j, and 630j
Branding Guide
Overview of the CTS2600, 620j,
and 630j
LSI provides unbranded CTS2600, 620j, and 630j systems to vendors so that Systems
Builders and Systems Integrators can brand the systems and integrate them into their
own branded solutions.
Figure 1 shows a three-quarter view and a front view of the CTS2600-24 and the 620j
for 24 2.5" drives. Figure 2 shows a three-quarter view and a front view of the
CTS2600-12 and the 630j for 12 3.5" drives.
Figure 1: CTS2600-24 and 630j for 24 2.5" drive
Figure 2: CTS2600-12 and 630j for 12 3.5 inch drives
CTS2600, 620j, and 630j
This document shows Systems Builders and Systems Integrators how to brand these
building blocks to integrate them into their own branded solutions.

Page 4 LSI Corporation Confidential | ***Release Date***
Branding Guide for the LSI 2600, LSI 620j. and LSI 630jCTS2600-24 and 620j for 2.5" drives
CTS2600-24 and 620j for 2.5"
drives
This section describes the branding specifications for the CTS2600-24 and 620j for 2.5"
drives.
CTS2600-24 and 620j drive canister Figure 3 shows the drive canister and LED displays of the CTS2600-24 and the 620j for
24 2.5" drives. Figure 4 shows the drive lever badge. Figure 5 shows the drive lever
badge assembly and its branding specifications.
Figure 3: Drive canister and LED display of the CTS2600-24 and 620j
Figure 4: Drive lever badge of the CTS2600-24 and 620j

LSI Corporation Confidential | ***Release Date*** Page 5
Branding Guide for the LSI 2600, LSI 620j. and LSI 630j CTS2600-24 and 620j for 2.5" drives
Figure 5: Drive lever badge assembly of the CTS2600-24 and 620j
12. FOR ALL PARTS PURCHASED TO THE MECHANICAL DRAWING, EACH SHIPMENT MUST HAVE
A CERTIFICATE OF COMPLIANCE LISTING THE MATERIAL LISTED BELOW AND THE
PURCHASE PART NUMBER.
11. PART IDENTIFICATION:
BAG AND TAG WITH PART NUMBER, REVISION AND DATE.
10. RADII: EDGES AND CORNERS REPRESENTED SHARP IN 3D DATABASE MAY BE FILLETED
UPON APPROVAL.
9. SECONDARY OPERATIONS: NONE.
8. FINISH: PART MUST BE FREE FROM IMPERFECTIONS, SCRATCHES. NO FLASH OR
TRIM MARKS ON SURFACE MARKED.
7. MATERIAL:
A.LCR530 RESIN WITH DK900 CATALYSIS 1.78 .25MM THICK ALTERNATE : LCR 54C
RTF RESIN WITH DK124 HV CATALYST 1.78 .25MM THICK.
B.13MM THICK POLYESTER. ARTWORK PRINTED DIRECTLY ON THE TOP SURFACE.
C.BACKING ADHESIVE MATL : 3M 200MP ADHESIVE, ALTERNATE :3M 9172MP
ADHESIVE.
6. 3D DATABASE FEATURES TAKE PRECEDENCE OVER 2D DRAWINGS. REFER TO 3D
DATABASE FILES(S)
5. DIMENSIONS ON ASSEMBLY DRAWINGS ARE REFERENCE DIMENSIONS. TOLERANCES ON
THOSE DIMENSIONS NORMALLY REPRESENT VALUES ARRIVED AT THROUGH A STANDARD
RSS TOLERANCE ANALYSIS. THEY ARE GOVERNED BY THE PROCESS CAPABILITY
SECTION OF ENG STD 3-03-02.MEETING THE ASSEMBLY DIMENSION DOES NOT
ABSOLVE THE REQUIREMENT THAT ALL PIECE PARTS MEET TOLERANCE AS WELL.

Page 6 LSI Corporation Confidential | ***Release Date***
Branding Guide for the LSI 2600, LSI 620j. and LSI 630jCTS2600-24 and 620j for 2.5" drives
4. SEE ENGINEERING STANDARD 3-03-02 FOR STANDARD TOLERANCES, APPEARANCE
STANDARDS AND OTHER MATERIAL / PROCESS REQUIREMENTS.
3. CERTIFICATE OF COMPLIANCE WITH EUROPEAN ROHS STANDARD SHALL BE INCLUDED
WITH EACH LOT OF PARTS PURCHASED TO THIS DRAWING.
2. DIMENSIONS CIRCLED ARE CRITICAL DIMENSIONS, AND SHALL BE KEPT UNDER SPC.
1. DIMENSIONS SHOWN ARE TO BE CONSIDERED INSPECTION DIMENSIONS AND SHALL BE
USED FOR THE INSPECTION PROCESS AND REPORTING. PART TO BE BUILT TO 3D
SOURCE FILE, WHICH TAKES PRECEDENCE OVER 2D DRAWING. STANDARD TOLERANCES
APPLY TO ALL 3D SOURCE FILE FEATURES PER ENGINEERING STANDARD 3-03-02
(AGILE 23564-00). UNDIMENSIONED FEATURES MUST MEET THESE TOLERANCE
REQUIREMENTS.
NOTES:
CTS2600-24 and 620j end caps Figure 6 and Figure 8 show two views of the right end cap of the bezel of the
CTS2600-24 and the 620j. Figure 8 shows the left end cap of the CTS2600-24 and the
620j.
Figure 6: Right end cap of the bezel of the CTS2600-24 and the 620j

LSI Corporation Confidential | ***Release Date*** Page 7
Branding Guide for the LSI 2600, LSI 620j. and LSI 630j CTS2600-24 and 620j for 2.5" drives
Figure 7: Right end cap of the Bezel of the CTS2600-24 and the 620j (cont.)
NOTES:(UNLESS OTHERWISE SPECIFIED)
1. ALL MATERIALS MUST COMPLY WITH 2002/95/EC
2. DRAWINGS FOR INSPECTION PURPOSES ONLY, ACTUAL PART SHALL CONFORM TO 3D
ELECTRONIC DATABASE. DO NOT SCALE DRAWING
3. MATERIAL: ABS+PC, EcoTech Polymers PC/ABS PCABSFR401e MATERIAL MUST BE UL
RECOGNIZED COMPOMENT PLASTIC MATERIALS, NOTED 94V-0 MINIMUM.
4. COLOR : BLACK
5. FINISH : NONE
6. TEXTURE TO MATCH MT-1055-1: TEXTURE ON INDICATED EXTERNAL SURFACES,
TEXTURE TRANSITIONS BETWEEN TEXTURED SURFACES. ALL TEXTURED SUFACES TO BE
GRADE B-2 OR BETTER PER SPI COSMETIC SPECIFICATION
7. MOLD FINISH ON INTERIOR (NON-APPEARANCE) SURFACES TO BE: SPI/SPE#3.
8. DRAFT PER 3D PART MODEL UNLESS OTHERWISE SPECIFIED IN DRAWING.
+ DIMENSION INCREASES WITH DRAFT
- DIMENSIONS DECREASES WITH DRAFT
9. MOLD: PARTING LINE MISMATCH AND/OR FLASH NOT TO EXCEED 0.2MM. MOLD DESIGN
TO MINIMIZE EJECTION PIN MARKS, WELD LINES, AND GATE BLUSH.
■INDICATES CTF(CRITICAL TO FIT/FUNCTION) DIMENSIONS.
●INDICATES QC(QUALITY CONTROL) DIMENSIONS.
10. SEE ENGINEERING STANDARD 3-03-02 FOR APPEARANCE STANDARDS.
11. ASSEMBLY AND DISASSEMBLY MUST COMPLY WITH 2002/96/EC.

Page 8 LSI Corporation Confidential | ***Release Date***
Branding Guide for the LSI 2600, LSI 620j. and LSI 630jCTS2600-24 and 620j for 2.5" drives
Figure 8: Left end cap of the CTS2600-24 and the 620j

LSI Corporation Confidential | ***Release Date*** Page 9
Branding Guide for the LSI 2600, LSI 620j. and LSI 630j CTS2600-24 and 630j for 3.5" drives
CTS2600-24 and 630j for 3.5"
drives
CTS2600-12 and 630j drive canister Figure 9 shows the drive canister and LED displays of the CTS2600-12 and the 630j for
12 3.5" drives. Figure 10 shows the drive lever badge. Figure 11 shows the drive lever
badge assembly and its branding specifications.
Figure 9: Drive canister and LED display of the CTS2600-12 and 630j
Figure 10: Drive lever badge of the CTS2600-12 and 630j


Page 10 LSI Corporation Confidential | ***Release Date***
Branding Guide for the LSI 2600, LSI 620j. and LSI 630jCTS2600-24 and 630j for 3.5" drives
Figure 11: Drive lever badge assembly of the CTS2600-12 and 630j
CTS2600-12 and 630j end caps Figure 12 shows the right end cap of the CTS2600-12 and the 630j. Figure 13shows the
left end cap of the CTS2600-12 and the 630j.