LTV SUPER DNR3 HIGH RESOLUTION User manual

Color Box Camera
Owner’s Manual
Super DNR3 High Resolution
www.ltv-cctv.ru
www.ltv-cctv.ru

Caution 2
Features 3
Warning 4
Components 5
Main Parts 6
Drawing 8
Installation 9
Connection 12
Camera Operation 14
Menu 14
Settings 15
LENS 16
EXPOSURE 17
SENS UP 18
AGC(Auto Gain Control) 18
SHUTTER
18
WHITE BALANCE CONTROL 19
BACKLIGHT COMPENSATION 20
RETURN 18
DNR3 22
DAY / NIGHT 24
IMAGE ADJ 26
CAM TITLE 28
MONITOR 27
SYNC 29
MOTION DET 30
PRIVACY 31
COMM ADJ 32
SPECIAL 25
EXIT 32
LANGUAGE 32
RETURN 32
Troubleshooting 33
Specifications 36
12

1) Do not install the camera in extreme temperature condition.
Only use the camera under conditions where temperatures are between
-10C and +50C. Be especially careful to provide ventilation when operating
under high temperatures.
2) Do not install or use the camera in a environment where the
humidity is high.
It can cause the image quality to be poor.
3) Do not install or use the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
4) Do not touch the front lens of the camera.
This is one of the most important parts of the camera. Be careful not to leave fingerprints
on the lens cover.
5) Do not drop the camera or protect it from physical shocks.
It can cause malfunctions to occur.
6) Never keep the camera pointed directly at strong light.
It can damage the CCD.
7) Do not expose the camera to radioactivity.
If exposed to radioactivity the CCD will fail.
8) The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
9) Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
10) Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
11) Do not hold plug with wet hands.
It could cause an electric shock.
12) Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
13) Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
4
3
Ultra High Resolution
By adopting a diagonal 410,000 (PAL) pixel
Sony CCD, the camera produces clear picture
quality with a horizontal resolution of 600 TV
lines for color, and 700 TV lines for B/W.
Wide Dynamic Range (WDR) Option
By adopting a proprietary WDR DSP chip, the
camera delivers clear, high quality pictures
even in backlight, by increasing exposure in
dark areas while decreasing it in bright areas;
a corrected image with clear details results.
Excellent Sensitivity
Adopting a Diagonal 6mm (1/3"), highly
sensitive CCD and digital signal processing
technology, it can clearly distinguish the outline
and color of a subject in an extremely low
luminance environment – even.
DNR3 (Super Noise Reduction) Function
The high performance W-V DSP chip
dramatically reduces the gain noise in digital
image processing, producing clear, sharp
images in low lighting environments.
True Day & Night
The camera identifies whether it is day or
night and automatically switches to the
appropriate mode, depending on its
environment. By day, the camera switches to
color mode in order to maintain optimal color.
At night, it switches to B/W mode so as to
obtain better picture definition.
Vari-focal Lens Built-in
With built-in vari-focal lens, the camera can
control the focal distance easily from 2.8 to
12mm.
DIS (Digital Image Stabilizer)
The DIS function compensates for any camera
movement, to produce more stable pictures.
Sub Monitor Function
The sub monitor function enables easy
adjustment of the camera angle within the
monitoring range during its installation.
RS-485 Communication (Option)
Control Support
Remote OSD menu control via an RS-485
interface is supported.
OSD
The camera control is convenient by using
different foreign language O.S.D.
- NTSC : Korean, English, Spanish, Japanese
French, Portuguese, Taiwanese
- PAL : English, French, German, Spanish,
Italian, Chinese, Russian, Czech, Polish,
Romani, Serbian, Swedish, Danish,
Turkish, Portuguese
Additional Functions
SYNC(INT/LL), SENS-UP, FREEZE,
FLIP(H/V-REV), D-ZOOM, SHARPNESS,
MOTION DETECTION and PRIVACY functions
are provided.

56
Overview
1) Lens
We support a variety of DC Iris or Video Auto Iris type lenses. Use the
appropriate switch setting for the type of lens you are using.
2) Camera Body
This houses the electronics module, back PCB and Dual PCB.
3) Rear Panel
Connectors and OSD functions are located here.
4) Mount Adapter
Use this bracket to affix the camera to the desired support bracket. You can
mount the support bracket on either side Top or bottom.
Overview
1) 2) 3)
4)
Allen-WRENCH

78
Backview
1) Auto IRIS Lens Connector
This is the connection terminal for the auto iris lens.
2) Auto IRIS Lens selection switch
Please change the mode to DC or VIDEO depending on the type of the auto
iris lens being used.
3) VIDEO output terminal
Sends video signals and connects to the video input terminal of the monitor.
4) Power Lamp
Lights up when the correct is supplied to the camera.
5) SETUP Switch
This switch is used to set the function or property. When this switch is pressed
and the MAIN MENU appears.
Left/Right) : By pressing this switch left or right, you can move left or right(
on the menu or change the displayed value.
Up/Down) : By pressing this switch up or down, you can move up or(
down on the menu.
: When you press this switch in the menu, the selected function is
confirmed. To enter a submenu, press this button.
6) Power Connection Port
This is connected to the Power cable. And now we sported DC12V only and
DC12V/AC24V 2types.
Drawing (mm)
IRIS LENS FRONT
BODY
BACK
1) 2) 3)
4)
6)
5)
Assembly

910

11 12
- As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
- If necessary, you can connect the monitor to the REMOTE jack on the back of
your camera.
- Only connect the cable when the power is turned off.
- Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.
1) Connection to Monitor
2) Connection to Power
Connect the adaptor to the power input connector as shown in the following figure .
The Standard voltage for camera operation : DC 12V ± 10%, AC 24V±10%.
AC 230V
Note
AC-230V
AC 230V

13
Menu ltem Option
LENS
(selection) ◇DC ◇VIDEO ◇Manual
EXPOSURE ◇BRIGHTNESS ◇SHUTTER ◇AGC
◇SENS-UP(x 512) ◇RETURN
WHITE BAL.
(White Balance)
◇ATW ◇OUTDOOR ◇INDOOR
◇MA NUA L ◇AWC-SET
SSDR ◇ON ◇OFF
BACKLIGHT ◇OFF ◇BLC ◇HLC
DNR3 ◇ON ◇OFF
DA Y / NIGHT ◇COLOR ◇B/W ◇AUTO ◇EXTENA L
SPECIAL
◇IMA GE A DJ ◇MONITOR ◇CA M TITLE
◇SYNC ◇MOTION DET ◇PRIV A CY
◇COMM A DJ ◇LANGUAGE ◇RETURN
EXIT ◇SAV E ◇NOT SA V E ◇RESET
SET UP M e n u
14
3) Connection to RS-485 (Option)
RED
WHITE
Control Cable
Spec
Red (TRX+)
White (TRX-)
RS-485+
RS-485-
Using a RS-485 communication, it will be able to control the OSD menu at the
System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside camera
and serial cable
EX) SERIAL PORT OF THE PC(COM1) SERIAL CABLE RS-485
→→
CONVERTER RS-485 CONTROL CABLE→
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control
boards which are connected with the DVR or System Controller.
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL RED (TRX+)
(- ) CONNECTION TERMINAL WHITE (TRX-)
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
ENABLE
çRS-485 Communication establishment initial value
When you connecting to RS-485 control cable, please peel off the outer skin-
inside the RS-485 control cable.

16
15
UP
RIGHT
DOWN
LEFT
UP
RIGHT
DOWN
LEFT
SET
OSD Board
Settings can be made using the 5 buttons located on the nearby of the camera.
UP BUTTON
RIGHT BUTTON
DOWN BUTTON
LEFT BUTTON
SET BUTTON
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
1.LENS DC
ATW
OFF
4

18
4SHUTTER : You can select either auto or manual shutter.
- --- : The shutter speed is fixed.(NTSC mode l: 1/60 sec, PAL model : 1/50 sec)
- ESC : Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient illumination
of the subject.
- MANUAL : You can control shutter speed manually.
Select this when you experience picture flicker, which can happen when- A.FLK :
there is a clash with the frequency of the installed lighting.
• If you press the Function Setup switch in ‘AUTO’ mode, You can adjust brightness
by increasing or decreasing the shutter speed. (X2~X512)
• Note that the higher the zoom level, the brighter the screen, but the more likely it
is that an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation
when the zoom level is increased, this is normal.
• To produce better results with A.FLK, do not use it in conjunction with the WDR
mode of the BACKLIGHT menu.
• When the SHUTTER is set to A.FLK mode, SENS-UP will be disabled.
4AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
Deactivates the AGC function.- OFF :
Allows automatic gain control from 0 to 30dB.- LOW :
Allows automatic gain control from 0 to 42dB.- HIGH :
4SENS-UP :
When it is night or dark, the camera automatically
detects the light level and maintains a clear picture
if this mode is activated.
Deactivates the SENS-UP function.- OFF :
Activates the SENS-UP function.- AUTO :
4RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
LIMIT
Press SET to Return
AUTO X2
4
17
1. When the SETUP menu screen is displayed, select EXPOSURE by using the
Function Setup switch so that the arrow indicates EXPOSURE .
2. Select a desired mode using the Function Setup switch.
EXPOSURE
Manual : manual lens selection
VIDEO : Auto iris lens selection , pin connection please refer to before LENS use.
DC : You can adjust the minimum shutter and maximum value of ESC shutter mode.
EXPOSURE SETUP
3.AGC HIGH
OFF
4.SENS-UP
5.RETURN
2.SHUTTER
1.BRIGHTNESS
___
4
•
• FOCUS ADJ : To adjust the DC lens focus correctly, you must activate
the focus Settings mode under each lens menu. Activate the Focus
Setting mode, adjust the lens focus, and then deactivate the settings
mode.
DC LENS
2.IRIS SPEED
3.FOCUS ADJ
4.RETURN
1.BRIGHTNESS
425
3
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4
25

19
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSNR
1.LENS DC
ATW
OFF
4
4 INDOOR : Select this when the color temperature is between 4500°K and 8500°K.
4 OUTDOOR : Select this when the color temperature is between 1800°K and
10500°K. (sodium light inclusion).
WB MANUAL
RGAIN
4
529
BGAIN 532
Press SET to Return
4
4
20
4
4SET
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
1.LENS DC
MANUAL
4
SSDR(Samsung Super Dynamic Range)
SSDR illuminates darker sports of an image white retaining the same light level
for brighter spots to even out the overall brightness of image with high contrast
between bright and dark spots.
1. When the SETUP menu screen is displayed, select "SSDR" by using the switch
so that the arrow indicates "SSDR".
2. Use the switch to change the SSDR level according to the contrast between
bright and dark areas.
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSNR
1.LENS DC
ATW
ON
4
SSDR SETUP
LEVEL
4
8
Press SET to Return
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
1.LENS DC
ATW
OFF
OFF
4

21
BLC :
Enables a user to directly select a desired area from a picture, and to view
the area more clearly.
4
HLC ( High Light Compensation ) :
if there is a high light installed in a limited environment such as an apartment
parking garage or others entrance, removing the high light makes it possible
to view car number efficiently.
4
-- Day : In normal daylight conditions, the HLC is not activated.
-- Night : if a high light that is larger than a certain size is present on the screen,
remove the high light to see the license plates clearly.
4
BLC ON
HLC ON
BLC OFF
HLC OFF
HLC MASKING AREA
3. Select a desired mode using the Function Setup switch and press.
BLC SETUP
MIDDLELEVEL
4
TOP 38
BOTTOM 109
LEFT 54
RIGHT 121
Press SET to Return
BLC HLC
22
• You cannot use the WDR mode when MANUAL or A.FLK mode in ‘SHUTTER’
menu is selected.
• Since the following symptoms may occur according to the ambient illumination
when WDR is selected, set it to OFF.
1) Color or screen changes unnaturally.
2) Noise appears in the bright part of the screen.
• Since the performance of the WDR function may be affected by the area of the
bright part of the screen, optimize the installation angle for the best WDR
performance.
• If you increase LIMIT, the screen display may be distorted.
DNR3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ’DNR3’ by using the Function
Setup switch so that the arrow indicates ’DNR3’ .
• When you use WDR module,WDR
function can be use .
Please select WDR to adjust the WDR
LIMIT and LEVEL.
Adjust the WDR Sensitivity by- LIMIT :
selecting LOW, MIDDLE, or HIGH.
- LEVEL : Adjust the WDR Brightness
by controlling the bar from 0 to 100.
WDR LIMIT
LIMIT
4MIDDLE
LEVEL 50
Press SET to Return
HLC SETUP
NIGHT ONLYLIMIT
BLACKMASK COLOR
MASK TONE
MIDDLELEVEL
4
TOP 5
1
BOTTOM 120
LEFT 35
RIGHT 172
Press SET to Return
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4

24
DAY/NIGHT
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the
Function Setup switch so that the arrow indicates DAY/NIGHT .
2. Select a desired mode using the Function Setup switch according to the picture
display you want.
The picture is always displayed in color.4COLOR :
The picture is always displayed4B/W :
in black and white.
The mode is switched to Color in a4AUTO :
normal environment, but switches to
B/W mode when ambient illumination
is low. To set up the switching time or
speed for AUTO mode, press the
Function Setup switch.
— You can turn on or off the burstBURST MODE :
signal on B/W mode.
— You can select brightness ofDURATION :
illumination about changing the
day/night mode.
— You can select the duration timeDWELL TIME :
about changing the day/night
mode. 3s, 5s, 7s, 10s, 15s, 20s,
30s, 40s, 60s.
BW MODE SETUP
AUTO SETUP
2. RETURN
2. COLO R B/W
BURATION
DWELL TIME
3. B/W CO LOR
4. RETURN
BURATION
DWELL TIME
1. BURST MODE ON
ON
FAST
3 SEC
FAST
10 SEC
4
1. BURST MODE
4
Press SET to Return
Press SET to Return
23
3. Set the DNR3 mode to ‘ON’ and press the Function Setup switch. Then you can
adjust the noise reduction level.
DNR3
LEVEL
4
10
Press SET to Return
• You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE
menu is ‘OFF’.
• When adjusting the noise reduction level of the DNR3 mode, remember that the
higher the level set, the more the noise level will be reduced but that after image
may also occur.
2. Select a desired mode using the Function Setup switch.
Deactivates DNR3. Noise is not reduced.4OFF :
Activates DNR3 so that noise is reduced.4ON :
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4

25
4EXTERN : This mode allows you to apply a desired filter to external signals.
• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu
is ‘OFF’.At this time, the exchange between DAY mode and NIGHT mode operates
as like selecting ‘COLOR’ mode.
• The OSD key does not work for 3 seconds when switching to Color or B/W, to
ensure stable camera operation.
• The camera may focus less well under infrared illumination than under normal
illumination.
Color B/W→
Fast
Slow
B/W Color→
2.5 Lux 5 Lux
1 Lux 10 Lux
26
SPECIAL
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates ‘SPECIAL’.
MAIN SETUP
2.EXPOSURE
3.WHITE BAL.
4.SSDR
5.BACKLIGHT
8.SPECIAL
9.EXIT
7.DAY/NIGHT
1.LENS
6.DNR3
DC
ATW
OFF
OFF
ON
AUTO
SAVE
4
2. Select a desired mode using the Function Setup switch.
SPECIAL
2.MONITOR
OFF
LCD
OFF
OFF
ENGLISH
INT
3.CAM TITLE
4.SYNC
5.MOTION DET
6.PRIVACY
7.COMM ADJ
8.LANGUAGE
9.RETURN
1.IMAGE ADJ
4
4 IMAGE ADJ.
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the
Function Setup switch so that the arrow indicates ‘IMAGE ADJ.’
SPECIAL
2.MONITOR
OFF
LCD
OFF
OFF
ENGLISH
INT
3.CAM TITLE
4.SYNC
5.MOTION DET
6.PRIVACY
7.COMM ADJ
8.LANGUAGE
9.RETURN
1.IMAGE ADJ
4
2. Select a desired mode using the Function Setup switch.
IMAGE SETUP
OFF
OFF
WHITE
ON
OFF
OFF
1.V-REV
2.H-REV
3.D-ZOOM
5.FONT COLOR
6.SHARPNESS
7.RETURN
4.DIS
4
SPECIAL
2.MONITOR
OFF
LCD
OFF
OFF
ENGLISH
INT
3.CAM TITLE
4.SYNC
5.MOTION DET
6.PRIVACY
7.COMM ADJ
8.LANGUAGE
9.RETURN
1.IMAGE ADJ
4

27
4CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so
that the arrow indicates ‘CAM TITLE’.
2) Set it to ‘ON’ by using the Function Setup switch.
28
When the CAM TITLE menu is ‘OFF’,
no title will be displayed on the
monitor screen even if you enter one.
- V-REV : You can flip the picture vertically on
the screen.
- H-REV : You can flip the picture horizontally on
the screen.
- D-ZOOM : You can use a digital zoom of
x1~x16.
- This function mitigatesDIS (Digital Image Stabilizer) :
any picture movement due to external factors
such as wind.
- You can change the OSD font color.FONT COLOR :
(White, Blue, Red, Green, Yellow, )
- SHARPNESS :
As you increase this value, the picture outline
becomes stronger and clearer. Adjust this value
appropriately depending on the sharpness of
the picture.
- Select this to save the settings for the IMAGE ADJ. menu and toRETURN :
return to the SETUP menu.
MONITOR :4Please change the settings value of video
appropriate to your monitor.
- LCD :Please select this menu item when using a LCD monitor.
- CRT : Please select this menu item when using a CRT monitor.
- USER :Please use this menu item when using a monitor other than standard ones.
You can change the gamma, PED level, and color gain in the sub menus.
D-ZOOM LEVEL
D-ZOOM
41.0
Press SET to Return
• When H-REV or V-REV is selected, any text in the picture also will be flipped
horizontally or vertically.
• If you increase the SHARPNESS level too high, the picture may become distorted
or noise may appear.
SHARPNESS
LEVEL
415
Press SET to Return
Press SET to Return Press SET to Return
LCD MONITOR
0.55
GAMMA
PED LEVEL
COLOR GAIN
RESET
4
17
50
CRT MONITOR
4
PED LEVEL
COLOR GAIN
RESET
17
50
SPECIAL
2.MONITOR
OFF
LCD
OFF
INT
3.CAM TITLE
4.SYNC
5.MOTION DET
1.IMAGE ADJ
4

29
4
-
-
LINE LOCK
PHASE
MODE OFF
4
15
Press SET to Return
4MOTION DET:
If you connect an alarm device to this
camera, you can monitor activity
more efficiently, because a signal is
generated by the camera whenever
motion is detected.
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the arrow indicates ‘MOTION DET’.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
Determines the coordinate of the horizontal axis for SEL POS.- XPOS :
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- FILL SET :
→Fills in a selected MD area. Fills in a selected MD area. The color of filling
is sequentially selected as brown, orange, blue, cyan, yellowish green,
yellow and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the
SPECIAL menu.
MOTION DET
2.AREA MODE
L-TO P
AREA1
ON
3.SEL POS
5.YPOS
4.XPOS
6.FILL SET
→
7.RETURN
1.SCNSITIVITY
4
3
5
30

31
• MD areas show only MOTION DET menu. Therefore, MD areas don’t display on
the monitor screen.
• When motion is detected, “MOTION DETECTION” expression is displayed on the
screen.
4PRIVACY :
Hide an area you want to hide on the
screen.
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates ‘PRIVACY’.
2) Set up the mode using the Function Setup
switch.
- AREA : You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area
selected in the AREA.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
PRIVACY
2.MODE OFF
GREEN3.MASK COLOR
AREA11.AREA
4
9.RETURN
4.MASK TONE 1
5.TOP 39
6.BOTTOM 79
7.LEFT 13
8.RIGHT 52
32
COMMUNICATION SETUP
2.BAUD REAT
8-N-1
1
9600
3.UART MODE
4.RET PKT
1.CAM ID
4
5.DISP ID
6.PROTOCOL
7.RETURN
ENABLE
OFF
SAMSUNG-T
4COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the
camera through an external control device.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch
so that the arrow indicates ‘COMM ADJ’.
2) Set up the mode using the Function Setup switch.
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the controller device
when a communication control command is sent to the camera.
- DISP ID : Display camera title on top left corner of the screen.
- PROTOCOL : You can select one of various protocols. SAMSUNG-T, SAMSUNG-E,
PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYWELL.
öInitial value of communication adjustment
4LANGUAGE : You can select the menu language according to your requirements.
4RETURN : Select this to save the SPECIAL menu settings and return to the
SPECIAL menu.
Select a desired EXIT mode using the Function Setup Switch.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language,
Communication and Monitor Settings are not initialized.
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
ENABLE

33 34

35
RS-485
Communication fails.
Check the polarity between RS-485 Control Port
and RS-485 cable.
Check the RS-485 Communication establishment
initial value
RS-485 Communication establishment initial valueö
We recommend that you make ground connect
between camera and controller in order to maintain
safety communication control.
Isn’t DAYNIGHT function setting up the color mode?
Please change the AUTO or B/W mode.
485 Control Board Connection Port RS-485 Control Port
(+) CONNECTION TERMINAL (TRX+) 485+
( - ) CONNECTION TERMINAL (TRX-) 485-
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
ENABLE
36
0.4 Kg
Diagonal 6mm (1/3") Sony HAD CCD
Color : 600 TV Lines B/W : 700 TV Lines
RS-485 (2400, 4800, 9600, 19200, 38400, 57600 bps selectable)
Coaxial(Pelco), RS-485(SAMSUNG-T, SAMSUNG-E, PELCO-P,
PELCO-D, VICON, PANASONIC, BOSCH, HONEYWELL)
Coaxial, RS-485
Communication
52 dB (AGC Off)
DNR3
V-REV(Mirror)
H-REV(Flip)
DIGITAL ZOOM
SHARPNESS
DIS
CAMERA TITLE
DAY / NIGHT
Back-light Compensation
0.15 Lux (Color at F1.2), 0.0 Lux (IR ON) , 0.0003 Lux(Sens-up X512)
Fixed (1/60 or Flickerless Mode) Fixed (1/50 or Flickerless Mode)
AUTO / OFF (Selectable limit x2 ~ x512)
ON / OFF (8 Zones)
ON / OFF (Level adjustable)
COLOR / Black & White / AUTO / EXTERN
DC drive Lens
ON / OFF (12 Zone)
ON / OFF
ON / OFF
ON / OFF(x1 ~ x16)
ON / OFF
ON / OFF (Displayed 15 characters)
ON / OFF (Level Adjustable)
ATW / Outdoor / Indoor / Manual / AWC (1700°K ~11,000°K)
LOW / HIGH / OFF
BLC / HLC OFF
170 mA
IR LED isn't lighted