GVI Security GV-SCS530 User manual

GVI Security
2801 Trade Center Dr., Suite 120 • Carrollton, TX 75007 • Toll Free: 888-595-2288 • www.gviss.com
GVI Security
2801 Trade Center Dr., Suite 120 • Carrollton, TX 75007 • Toll Free: 888-595-2288 • www.gviss.com
GV-SCS530 Users Manual
v.11.06.08
INTEGRATED PTZ POSITIONING
SYSTEM, 36X OPTICAL ZOOM, WDR,
D/N, INDOOR OUTDOOR CAMERA
before installing and using the camera, please read these instructions
thoroughly and retain them for later reference.

SUMMARY
The “Smart Camera System” GV-SCS530 is a high-performance, integrated positioning sys-
tem featuring a 530TV Lines resolution, 36x optical zoom camera, lens and complete PTZ unit.
Made from die-cast aluminum construction, with an IP66 rated weather-resistant design. The
GV-SCS530 has a built-in heater, wiper, window defroster, sun-shield, anti-fogging, dust-proof
and frost protection function. It can withstand high winds, offers complete 360-degree panning
with tilt ranges of +33 degrees and -83 degrees from the horizontal. What’s more, the camera is
equipped with a number of convenient functions such as Spherical Privacy Zone Masking with
Mosaic Effect, Video Motion Detection, Multi-Line On-Screen Display, E-ip, and Picture Freeze.
The GV-SCS530 is also compatible with many popular control protocols.
FEATURES
• 1/4 Inch type ExView HAD CCD
• 530TV Lines Resolution
• Minimum Scene Illumination: 1.4 lux @ 1/60s shutter speed, 0.1 lux @ 1/4s shutter speed
• 36x Optical Zoom (12x Digital zoom, 432x total)
• True Day/Night with IR Filter Removal
• Wide Dynamic Range
• E-ip
• Picture Freeze
• Advanced Spherical Privacy Zone Masking Function with Mosaic Effect
• Video Motion Detection
• Multi Line On-Screen Display
• Electronic shutter / slow shutter
• Internal / External synch (V-lock)
• Die-cast Aluminum construction, high temperature resistant
• Weather resistant, dust proof design, protection grade IP66
• 360° continuous panning
• Tilt range +33°~-80°
• Auto pan function between 2 presets
• 128 presets 6 tracks
• Anti fogging and frost protection function
• Wiper
• Factory presets
• Register set command
• RoHS-compliant
• Multi Protocol Control
• Included Wall Mount
NoTES

I. NOTES FOR ATTENTION
1. Read the manual carefully before installing the product.
2. Power Supply: 220V/110V/24V, refer to the sticker on the product.
3. Avoid incorrect shipping methods such as overstacking or strong vibration during the course
of transportation, storage and installation, as the product could be damaged.
4. Do not dismount components inside the product to avoid occurrence of trouble. There are no
user serviceable parts inside the camera.
5. Observe all electric safety standard in use and installation and use power supply attached
to the product. RS-485 and video signal should keep enough distance with the high voltage
devices and cable during the course of transmission, and take protection measures such as
anti-lightning and surging if necessary.
6. Do not use the product under conditions which exceeds the temperature, humidity or speci-
cations of power supply.
7. Do not aim the camera at the sun or very bright object or to monitor bright and still object,
whether the power supply is switched on or off.
8. Do not clean the product with strong or abrasive detergent. Clean out dirt with dry cloth or mild
detergent if dirt is not easily removed.
9. Take care to set up the product to avoid collision or vibration. Improper application can cause
damage.
10. Install the product in a location that is capable of supporting the Camera PTZ system weight.
11. Wipe dust on the lens with special lens paper.
WARNING:
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufcient magnitude to consti-
tute a risk of electric shock to persons.
SPECIFICATIONS
Model GV-SCS530
Image sensor 1/4” EX view HAD CCD
Number of total pixels Approx. 380,000 pixels
Lens 36x optical zoom,f=3.4 mm(wide)to 122.4 mm (tele), F1.6 to F4.5
Digital zoom 12x (432x with optical zoom)
Angle of view (H) 57.8° (wide end) to 1.7° (tele end)
Minimum object distance 320 mm (wide end) to 1,500 mm (tele end)
Sync system Internal / External (V-lock)
Minimum illumination 1/60s mode: 1.4 lux (typical)(F1.6, 50 IRE): 1/4s mode: 0.1 lux (typical)(F1.6, 50 IRE)
Horizontal Resolution 530TV Lines
Day & Night Yes, True D/N, IR Cut Filter Removal
S/N ratio More than 50dB
Electronic shutter 1/1 to 1/10,000s, 22 steps
White balance Auto, ATW, Indoor, Outdoor, One-push, Manual
Gain Auto / Manual (-3 to 28 dB, 2 dB steps)
AE control Auto, Manual, Priority mode (shutter priority & iris priority), Bright, EV compensation, Backlight
compensation, Slow AE
Wide Dynamic Range On / O: Wide-D, 128x
Backlight compensation On / O
Privacy zone masking On / O (8 masks per view/24 masks presets in the entire viewing range when integrated into a PTZ
camera - 14 colors, mosaic)
Character generator Mode display/Multi-line OSD (OSD has priority over Mode display)
Flicker cancel Auto
Focusing system Auto (Sensitivity: normal, low), One-push AF, Manual, Innity, Interval AF, Zoom Trigger AF
Picture eects E-Flip, Black & White, Mirror Image, Picture Freeze, Mirror
Image
Camera operation switch Zoom tele, Zoom wide
Video output VBS: 1.0 Vp-p (sync negative), Y/C
Dimensions (WxHxD) 16.14 x 13.38 x 6 in / 410 x 340 x 152 mm
Pan Preset speed 100°/s (wind speed low 50 mile/hour)
Tilt preset speed 30°/s (wind speed low 50 mile/hour)
Pan speed 0°~40°/ S
Tilt speed 0°~20°/ S
Pan range 360° continuously
Tilt range +33° ~-80°
Preset, track 128 presets, 6 tracks
Control way Multi-protocol, Baud rate from 2400Bps to 19200Bps, RS485 Control
Operating Temperature -35° ~ 55°C / -31° ~ 131° F
Relative humidity 90% Non Condensing
IP grade IP66
Power supply 24VAC
Power consumption 70VA
Weight 23.1 lb / 10.5 Kg
Protocols Pelco P, D, SAMSUNG
RISK OF ELECT RI C SHOCK
DO NOT OPE N
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK. NO
USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
CAUTION:
To prevent electric shocks and
risk of re hazards do NOT use
other than specied power
source.
12 1

1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
II. INTRODUCTION OF FUNCTIONS
1. Unlimited rotation 360° horizontally and from +33° to -80° vertically.
2. The horizontal speed is 0 - 40°/sec while the vertical speed is 0 - 20°/sec (wind speed less
than 50 miles/hour).
3. At the preset position, the horizontal speed is 0 - 100°/sec while the vertical speed is 0 - 40°/
sec (wind speed less than 50 miles/hour).
4. Automatic control of constant temperature, manual rain wiper/defroster control.
5. IP grade IP66.
6. The bearable maximum wind speed is 130 miles/hour.
7. 128 preset positions in memory and 6 groups of programmable patrol loci, as well as linear
scan between two points with adjustable speed and variable direction,
8. 16 common protocols integrated, four kinds of baud rate 2400/4800/9600/19200 bps available
and 1024 addresses are supported (0 - 1023).
III. QUICK GUIDE OF INSTALLATION
1. Modify the Protocol and the Address (jump over this section if no modication)
Remove the small metal cover on the bottom shown as dotted-lined part on Figure 3.1.1 to
expose DIP switch of the address and the protocol shown as Figure 3.1.2. The detailed draw-
ing is shown as in Figure 3.1.1.
Shown as Figure 3.1.3, the 10-bit DIP stands for the addresses which can be from 0 to 1023.
The 6-bit DIP stands for the protocols in which bits 1-4 mean the protocol while bits 5-6 means
the baud rate. Push the DIP downward means ON otherwise it means OFF. For example
the address in the gure means 1 while the protocol means PELCO-D with the baud rate of
2400bps which can be found from the table.
Shown as Figure 3.1.3, the 10-bit DIP stands for the addresses which can be from 0 to 1023.
The 6-bit DIP stands for the protocols in which bits 1-4 mean the protocol while bits 5-6 means
the baud rate. Push the DIP downward means ON otherwise it means OFF. For example
the address in the gure means 1 while the protocol means PELCO-D with the baud rate of
2400bps which can be found from the table.
The top line and the bottom line display prompt message, and the middle area displays infor-
mation of each locus, one line shows data of two points. Move the cursor by PAN LEFT/RIGHT
and modify data by TILT UP/DOWN. Press the button down for 1 second to accelerate. Press
CLOSE button to exit the edit state and store modication. In above gure, the program stores
four patrol points. The settable range of POS is from 1 to 63 or 65 to 128. In case POS is “---“,
it means the skip this point. The settable range of SP is from 0 to 8 (0 and 1 are same at the
highest speed while grade 8 has the lowest speed). The settable rage of TM is from 0 to 99
seconds.
Operation of the Title of Preset under Edit State
After entering into the edit state, the screen show as
the drawing. You can nd current setup is the preset 1
with the title “NO TITLE”. Move the cursor by PAN LEFT/
RIGHT and modify data by TILT UP/DOWN. Press the
button down for 1 second to accelerate. Press CLOSE
button to exit the edit state and save modication. The
title of preset can contain 8 characters such as 0~9, A~Z,
+, - and blank. Note: the rst letter should be 0~9 or A~Z
otherwise it means to delete the title of the presets and it
shall only show “NO.XXX” without the title when preset
points.
V. SPECIAL OPERATION
The preset 51 to 60 are used for special functions. It has special meanings to set or call these
points. Therefore these points should not be used in functions of automatic operation of the
pan/tilt such as multiple points patrol, external alarm linkage etc. so as to avoid error actions.
Preset Set Preset Call Preset
51 Wiper ON Wiper OFF
52 Defroster ON Defroster OFF
53 Auxiliary Output AC24V ON Auxiliary Output AC24V OFF
54 Linkage of External Alarm 1 ON Linkage of External Alarm 1 OFF
55 Linkage of External Alarm 2 ON Linkage of External Alarm 2 OFF
56 Reserved Reserved
57 Reserved Reserved
58 Reserved Reserved
59 Reserved Reserved
60 Reserved Reserved
Figure 3.1.1 Figure 3.1.1 Figure 3.1.3
211

Table 1 Table of Addresses in DIP Switch
Ad-
dress
of PT
Status of DIP Switch
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9 DIP-10
1ON OFF OFF OFF OFF OFF OFF OFF OFF OFF
2OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
3ON ON OFF OFF OFF OFF OFF OFF OFF OFF
4OFF OFF ON OFF OFF OFF OFF OFF OFF OFF
5ON OFF ON OFF OFF OFF OFF OFF OFF OFF
6OFF ON ON OFF OFF OFF OFF OFF OFF OFF
7ON ON ON OFF OFF OFF OFF OFF OFF OFF
8OFF OFF OFF ON OFF OFF OFF OFF OFF OFF
9ON OFF OFF ON OFF OFF OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF OFF OFF
... ... ... ... ... ... ... ... ... ... ...
1023 ON ON ON ON ON ON ON ON ON ON
Examples
PROGRAM
AUTO PAN START POS: to set the start point of the Au-
toPan. After entering, move the PT by the joystick. Push
CLOSE button to save the current position and return.
AUTO PAN END POS: to set the end point of the Auto-
Pan. After entering, move the PT by the joystick. Push
CLOSE button to store the current position and return.
RUN AUTO PAN: to run the AutoPan. Please set the
start point and the end point rst. If the start position and
the end position is the same position, the PT shall make
360°AutoPan. The speed of the AutoPan is divided into
six grades: FAST/NORMAL/SLOW/ -FAST/-NORMAL/-
SLOW. The rst three grades are the AutoPan less than
180° while the latter three grades are the AutoPan larger
than 180°. The speed can be adjusted by PAN LEFT/
PAN RIGHT. Push OPEN button to run and exit the menu. The start point and the end point
are set from options 1 and 2 on this menu.
SET TITLE: to edit the titles of preset. Only rst 63 presets may have their titles and the preset
number can be selected by PAN LEFT/PAN RIGHT. Press OPEN button to enter into the edit
state and press CLOSE button to exit the edit state. Operations under the edit state can be
seen thereafter.
SET PATROL: to edit patrol data. Select the number of patrol by PAN LEFT/PAN RIGHT.
Press OPEN button to enter into the edit state and press CLOSE button to exit the edit state.
Operations under the edit state can be seen thereafter.
RUN PATROL: to run patrol function. Select the number of patrol by PAN LEFT/PAN RIGHT.
Press OPEN button to run and exit the menu.
RECORD PATTERN: to recode pattern. It can remember PTZ operation for 40 seconds. Com-
plete the edit when 40 seconds are up or push CLOSE button.
RUN PATTERN: to playback pattern. You can also control the joystick to stop running.
RETURN: return to the main menu.
3. APPENDIX
Operation of Patrol under the Edit State
After entering into the edit state, the screen shows as follows:
NO – serial number of patrol
POS – number of preset
SP – leaving speed
TM – dwelling time
Enter into edit state, display on screen is as follows:
Edit Area, one line shows data of two point .
SEQ: 01 – it means current set patrol 1
CLOE: EXIT – push CLOSE to exit edit state
10 3

Type of Pro-
tocols
Selection of Communication Protocols
Common Baud Rates
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6
SAMSUNG ON OFF OFF OFF OFF ON
B01 ON OFF OFF OFF OFF ON
NEON ON OFF OFF OFF OFF ON
Santachi OFF ON OFF OFF OFF ON
PELCO-D ON ON OFF OFF OFF OFF
PELCO-P/4800
OFF OFF ON OFF
ON OFF
PELCO-P/9600 OFF ON
PANASONIC ON OFF ON OFF OFF ON
Longcomity OFF ON ON OFF OFF ON
HUNDA600 ON ON ON OFF OFF ON
LILIN OFF OFF OFF ON OFF ON
VICON ON OFF OFF ON ON OFF
MOLYNX OFF ON OFF ON OFF ON
KALATEL ON ON OFF ON ON OFF
VCL OFF OFF ON ON OFF ON
Reserved ON OFF ON ON OFF ON
ALEC OFF ON ON ON OFF ON
Ultrak ON ON ON ON OFF ON
Table 2 Table of Protocols in DIP Switch
Some protocols and their common baud rates in DIP switch are as follows:
2.2 DISPLAY SETUP
ID DISPLAY: When this option is set at ON, the monitor shall
display the address of the camera such as “CAM 001”.
ID POS: To set up the display location of the address, which
can be displayed at TOP-L (top left), TOP-R (top right),
BOTT-R (bottom right) and BOTT-L (bottom left).
TITLE DIS: when this option is set at ON, the title of the
presets can be displayed on the left of the screen when the
preset is called, such as “NO.001 ABCDEFGH”. If no title is
set, then only “NO. 001” is displayed. The modication of the
title of the preset is set on the PROGRAM option.
TITLE POS: to set the display location of the title of the preset, which can be from Line 1 to Line
10. The Line 1 is on the top of the screen.
CAM DISPLAY: when this option is set at ON, the display screen of the camera can be dis-
played.
RETURN: to exit the main menu.
CAMERA SETUP
SLOW SHUTTER: Slow Shutter function with Man/Auto options.
When the option be AUTO, ASS shall be displayed on the moni-
tor.
BACK LIGHT: Backlight Compensation ON/OFF.
ICR SHOT: Low Illumination, ON–open/AUTO–automatic.
IRIS: Automatic Exposure, AUTO–automatic/MANU–manual.
D-ZOOM: Digital Zoom, ON–open/OFF–close.
FOCUS: Automatic focusing, AUTO–automatic/MANU–manual.
WB SET: White Balance, ATW /INDOOR /OUTDOOR /ONE-
PUSH /AUTO /MANU
MENU OF CAM: this option is empty.
RETURN: return to the main menu.
CONTROL SETUP
WIPER: rain wiper control.
DEFROSTER: defroster control.
RESERVED AUX: auxiliary switch control.
ALARM1: external alarm 1 control.
LINKAGE1: set linkage with external alarm 1.
ALARM2: external alarm 2 control.
LINKAGE2: set linkage with external alarm 2.
HOME OPTION: enter the submenu of automatic
home function.
AUTO HOME: when this option is set at ON, home
position function is opened. This means the PT shall
return home position if user has no any action in a
period of time. The PT cannot return home position
automatically if it is under the patrol state. If no home
returning is needed under the stop state, please set
this option at OFF.
HOME POS: set home position. HOME POS can be
sat from preset 1 to preset 63, or preset 65 to preset
128.
DWELL TIME: set the time for home position, which means the PT shall go to home position
if no any control occurs within the set time from 1 to 99 minutes.
RETURN: return to the menu one level up.
RETURN: return to the main menu.
4 9

Baud Rates of
Communication
Setup of Baud Rates
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6
2400 bps - - - - OFF OFF
4800 bps - - - - ON OFF
9600 bps - - - - OFF ON
19200 bps - - - - ON ON
Table 3 Table of Baud Rates
View inward from the small hole on the bottom shown as in Figure 3.2.1, you can nd a 4-bit
DIP whose No.1 is the switch of the terminal resistor 120Ω, shown as in Figure 3.2.2. Set
No.1 of DIP at ON, then between Line A and Line B on 485 bus there is a terminal resistor
120Ωconnected. The default setup is at OFF which means the terminal resistor is opened.
Figure 3.2.1 Figure 3.2.2
3. Sizes
4. Wall Mounting
Step 1: Mount the bracket on the wall as shown in Figure 3.4.1. Figure 3.4.2 is the drawing of
sizes of mounting holes.
Figure 3.4.1 Figure 3.4.2
Red
Green
White
Blue
Red Alarm Input 1
Yellow Alarm Input 1
Green, Blue Alarm Common Terminal
The alarm input should be switch signal otherwise internal circuit shall be damaged.
The alarm shall be linked with the presser point, which should be set in the menu. In case two
channels have alarm signals simultaneously, the pan/tilt shall response upon two channels
one by one with the time interval of 2 seconds.
In case the alarm signal is inputted, the PT shall have no response upon functions such as
“AUTO PAN”, “Patrol” and “Pattern” and so on.
IV. DESCRIPTION OF MENU FUNCTIONS
1. Basic Operations on the Menu
Open the main menu by the control keyboard or the matrix via the instruction of “Call Preset
64”. In addition the main menu can be also opened by “Call Preset 1” twice within 4 seconds.
When the menu is displayed on the screen, operate “TILT UP”, “TILT DOWN” to move the cur-
sor to the options to be set up, and operate “PAN LEFT”, “PAN RIGHT” to modify the content
or the instruction to enter into this option.
The operation can be accelerated in case the joystick is pushed towards one direction for
more than 1 second.
All setups of the menu shall not be lost even after power failure.
The application under special cases can be seen in the instruction of functions of the menu.
2. Setup of the Menu
2.1 Main Menu
DISPLAY SETUP: Enter into the submenu to setup display on
the screen, such as ID DISPLAY, TITLE DISPLAY and CAM-
ERA DISPLAY.
CAMERA SETUP: Enter into the submenu of normal data of the
camera.
CONTROL SETUP: Enter into the submenu of the control data
of the PT.
PROGRAM: Enter into the submenu to setup enhanced func-
tion of the PT.
CAM DEFAULT SET: Restore camera default settings.
RESET PT: Reset of the PT.
EXIT: Exit the main menu.
5.2”
132mm
4.3”
110mm
5.9”
150mm
15.4” / 392mm
8.7” / 220mm
5.3”
135mm
7.4”
190mm
13.4”
340mm
7.1”
180mm
13.6” / 345mm
11.2” / 285mm
16.1” / 410mm
3.7”
95mm
2.8”
70mm
ø 0.4”
ø 9.0mm
3.0”
76mm
85

It is recommended to mount the system with M8 screw.
Step 1: There is a mobile plate on the underside of the support bracket. The plate can be
opened when the screws on the front are removed. Lead the wires of the system into the
bracket for connection.
Step 2: Put the pan/tilt unit on the support bracket and tighten screws upward beneath the
support, shown as in Figure 3.4.3.
Step 3: Using the M6×20 screws connect the output wires of the pan/tilt unit and the system,
wrap the joints with insulation tape and close the mobile plate under the support.
It should be like what Figure 3.4.4 shows.
Figure 3.4.3 Figure 3.4.4
5. Base Plate Mounting
Step 1: Drill holes on the ground, referring to the positions of holes on the mounting plate. The
sizes of holes are shown as in Figure 3.5.1.
Step 2: Fix the mounting plate on the bottom of the pan/tilt by M6×20 screw.
Figure 3.5.1
Figure 3.5.2
Step 3: Fix the mounting plate with the pan/tilt on the ground. Take care that wires are put into
the groove under the mounting plate to prevent the wires from being compressed. It is shown
as Figure 3.5.3
Figure 3.5.3
6. CONNECTIONS
Please refer to the descriptions of following drawing.
1) System Wires
RED Input of AC Power Supply
BLACK Input of AC Power Supply
YELLOW Control Wire RS485-（B（
ORANGE Control Wire RS485+（A（
VIDEO OUT Video Output
4.9” / 124.5mm
4.9”
125mm
3.6”
90.5mm
6.5” / 165mm
6 7

It is recommended to mount the system with M8 screw.
Step 1: There is a mobile plate on the underside of the support bracket. The plate can be
opened when the screws on the front are removed. Lead the wires of the system into the
bracket for connection.
Step 2: Put the pan/tilt unit on the support bracket and tighten screws upward beneath the
support, shown as in Figure 3.4.3.
Step 3: Using the M6×20 screws connect the output wires of the pan/tilt unit and the system,
wrap the joints with insulation tape and close the mobile plate under the support.
It should be like what Figure 3.4.4 shows.
Figure 3.4.3 Figure 3.4.4
5. Base Plate Mounting
Step 1: Drill holes on the ground, referring to the positions of holes on the mounting plate. The
sizes of holes are shown as in Figure 3.5.1.
Step 2: Fix the mounting plate on the bottom of the pan/tilt by M6×20 screw.
Figure 3.5.1
Figure 3.5.2
Step 3: Fix the mounting plate with the pan/tilt on the ground. Take care that wires are put into
the groove under the mounting plate to prevent the wires from being compressed. It is shown
as Figure 3.5.3
Figure 3.5.3
6. CONNECTIONS
Please refer to the descriptions of following drawing.
1) System Wires
RED Input of AC Power Supply
BLACK Input of AC Power Supply
YELLOW Control Wire RS485-（B（
ORANGE Control Wire RS485+（A（
VIDEO OUT Video Output
4.9” / 124.5mm
4.9”
125mm
3.6”
90.5mm
6.5” / 165mm
6 7

Baud Rates of
Communication
Setup of Baud Rates
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6
2400 bps - - - - OFF OFF
4800 bps - - - - ON OFF
9600 bps - - - - OFF ON
19200 bps - - - - ON ON
Table 3 Table of Baud Rates
View inward from the small hole on the bottom shown as in Figure 3.2.1, you can nd a 4-bit
DIP whose No.1 is the switch of the terminal resistor 120Ω, shown as in Figure 3.2.2. Set
No.1 of DIP at ON, then between Line A and Line B on 485 bus there is a terminal resistor
120Ωconnected. The default setup is at OFF which means the terminal resistor is opened.
Figure 3.2.1 Figure 3.2.2
3. Sizes
4. Wall Mounting
Step 1: Mount the bracket on the wall as shown in Figure 3.4.1. Figure 3.4.2 is the drawing of
sizes of mounting holes.
Figure 3.4.1 Figure 3.4.2
Red
Green
White
Blue
Red Alarm Input 1
Yellow Alarm Input 1
Green, Blue Alarm Common Terminal
The alarm input should be switch signal otherwise internal circuit shall be damaged.
The alarm shall be linked with the presser point, which should be set in the menu. In case two
channels have alarm signals simultaneously, the pan/tilt shall response upon two channels
one by one with the time interval of 2 seconds.
In case the alarm signal is inputted, the PT shall have no response upon functions such as
“AUTO PAN”, “Patrol” and “Pattern” and so on.
IV. DESCRIPTION OF MENU FUNCTIONS
1. Basic Operations on the Menu
Open the main menu by the control keyboard or the matrix via the instruction of “Call Preset
64”. In addition the main menu can be also opened by “Call Preset 1” twice within 4 seconds.
When the menu is displayed on the screen, operate “TILT UP”, “TILT DOWN” to move the cur-
sor to the options to be set up, and operate “PAN LEFT”, “PAN RIGHT” to modify the content
or the instruction to enter into this option.
The operation can be accelerated in case the joystick is pushed towards one direction for
more than 1 second.
All setups of the menu shall not be lost even after power failure.
The application under special cases can be seen in the instruction of functions of the menu.
2. Setup of the Menu
2.1 Main Menu
DISPLAY SETUP: Enter into the submenu to setup display on
the screen, such as ID DISPLAY, TITLE DISPLAY and CAM-
ERA DISPLAY.
CAMERA SETUP: Enter into the submenu of normal data of the
camera.
CONTROL SETUP: Enter into the submenu of the control data
of the PT.
PROGRAM: Enter into the submenu to setup enhanced func-
tion of the PT.
CAM DEFAULT SET: Restore camera default settings.
RESET PT: Reset of the PT.
EXIT: Exit the main menu.
5.2”
132mm
4.3”
110mm
5.9”
150mm
15.4” / 392mm
8.7” / 220mm
5.3”
135mm
7.4”
190mm
13.4”
340mm
7.1”
180mm
13.6” / 345mm
11.2” / 285mm
16.1” / 410mm
3.7”
95mm
2.8”
70mm
ø 0.4”
ø 9.0mm
3.0”
76mm
85

Type of Pro-
tocols
Selection of Communication Protocols
Common Baud Rates
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6
SAMSUNG ON OFF OFF OFF OFF ON
B01 ON OFF OFF OFF OFF ON
NEON ON OFF OFF OFF OFF ON
Santachi OFF ON OFF OFF OFF ON
PELCO-D ON ON OFF OFF OFF OFF
PELCO-P/4800
OFF OFF ON OFF
ON OFF
PELCO-P/9600 OFF ON
PANASONIC ON OFF ON OFF OFF ON
Longcomity OFF ON ON OFF OFF ON
HUNDA600 ON ON ON OFF OFF ON
LILIN OFF OFF OFF ON OFF ON
VICON ON OFF OFF ON ON OFF
MOLYNX OFF ON OFF ON OFF ON
KALATEL ON ON OFF ON ON OFF
VCL OFF OFF ON ON OFF ON
Reserved ON OFF ON ON OFF ON
ALEC OFF ON ON ON OFF ON
Ultrak ON ON ON ON OFF ON
Table 2 Table of Protocols in DIP Switch
Some protocols and their common baud rates in DIP switch are as follows:
2.2 DISPLAY SETUP
ID DISPLAY: When this option is set at ON, the monitor shall
display the address of the camera such as “CAM 001”.
ID POS: To set up the display location of the address, which
can be displayed at TOP-L (top left), TOP-R (top right),
BOTT-R (bottom right) and BOTT-L (bottom left).
TITLE DIS: when this option is set at ON, the title of the
presets can be displayed on the left of the screen when the
preset is called, such as “NO.001 ABCDEFGH”. If no title is
set, then only “NO. 001” is displayed. The modication of the
title of the preset is set on the PROGRAM option.
TITLE POS: to set the display location of the title of the preset, which can be from Line 1 to Line
10. The Line 1 is on the top of the screen.
CAM DISPLAY: when this option is set at ON, the display screen of the camera can be dis-
played.
RETURN: to exit the main menu.
CAMERA SETUP
SLOW SHUTTER: Slow Shutter function with Man/Auto options.
When the option be AUTO, ASS shall be displayed on the moni-
tor.
BACK LIGHT: Backlight Compensation ON/OFF.
ICR SHOT: Low Illumination, ON–open/AUTO–automatic.
IRIS: Automatic Exposure, AUTO–automatic/MANU–manual.
D-ZOOM: Digital Zoom, ON–open/OFF–close.
FOCUS: Automatic focusing, AUTO–automatic/MANU–manual.
WB SET: White Balance, ATW /INDOOR /OUTDOOR /ONE-
PUSH /AUTO /MANU
MENU OF CAM: this option is empty.
RETURN: return to the main menu.
CONTROL SETUP
WIPER: rain wiper control.
DEFROSTER: defroster control.
RESERVED AUX: auxiliary switch control.
ALARM1: external alarm 1 control.
LINKAGE1: set linkage with external alarm 1.
ALARM2: external alarm 2 control.
LINKAGE2: set linkage with external alarm 2.
HOME OPTION: enter the submenu of automatic
home function.
AUTO HOME: when this option is set at ON, home
position function is opened. This means the PT shall
return home position if user has no any action in a
period of time. The PT cannot return home position
automatically if it is under the patrol state. If no home
returning is needed under the stop state, please set
this option at OFF.
HOME POS: set home position. HOME POS can be
sat from preset 1 to preset 63, or preset 65 to preset
128.
DWELL TIME: set the time for home position, which means the PT shall go to home position
if no any control occurs within the set time from 1 to 99 minutes.
RETURN: return to the menu one level up.
RETURN: return to the main menu.
4 9

Table 1 Table of Addresses in DIP Switch
Ad-
dress
of PT
Status of DIP Switch
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9 DIP-10
1ON OFF OFF OFF OFF OFF OFF OFF OFF OFF
2OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
3ON ON OFF OFF OFF OFF OFF OFF OFF OFF
4OFF OFF ON OFF OFF OFF OFF OFF OFF OFF
5ON OFF ON OFF OFF OFF OFF OFF OFF OFF
6OFF ON ON OFF OFF OFF OFF OFF OFF OFF
7ON ON ON OFF OFF OFF OFF OFF OFF OFF
8OFF OFF OFF ON OFF OFF OFF OFF OFF OFF
9ON OFF OFF ON OFF OFF OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF OFF OFF
... ... ... ... ... ... ... ... ... ... ...
1023 ON ON ON ON ON ON ON ON ON ON
Examples
PROGRAM
AUTO PAN START POS: to set the start point of the Au-
toPan. After entering, move the PT by the joystick. Push
CLOSE button to save the current position and return.
AUTO PAN END POS: to set the end point of the Auto-
Pan. After entering, move the PT by the joystick. Push
CLOSE button to store the current position and return.
RUN AUTO PAN: to run the AutoPan. Please set the
start point and the end point rst. If the start position and
the end position is the same position, the PT shall make
360°AutoPan. The speed of the AutoPan is divided into
six grades: FAST/NORMAL/SLOW/ -FAST/-NORMAL/-
SLOW. The rst three grades are the AutoPan less than
180° while the latter three grades are the AutoPan larger
than 180°. The speed can be adjusted by PAN LEFT/
PAN RIGHT. Push OPEN button to run and exit the menu. The start point and the end point
are set from options 1 and 2 on this menu.
SET TITLE: to edit the titles of preset. Only rst 63 presets may have their titles and the preset
number can be selected by PAN LEFT/PAN RIGHT. Press OPEN button to enter into the edit
state and press CLOSE button to exit the edit state. Operations under the edit state can be
seen thereafter.
SET PATROL: to edit patrol data. Select the number of patrol by PAN LEFT/PAN RIGHT.
Press OPEN button to enter into the edit state and press CLOSE button to exit the edit state.
Operations under the edit state can be seen thereafter.
RUN PATROL: to run patrol function. Select the number of patrol by PAN LEFT/PAN RIGHT.
Press OPEN button to run and exit the menu.
RECORD PATTERN: to recode pattern. It can remember PTZ operation for 40 seconds. Com-
plete the edit when 40 seconds are up or push CLOSE button.
RUN PATTERN: to playback pattern. You can also control the joystick to stop running.
RETURN: return to the main menu.
3. APPENDIX
Operation of Patrol under the Edit State
After entering into the edit state, the screen shows as follows:
NO – serial number of patrol
POS – number of preset
SP – leaving speed
TM – dwelling time
Enter into edit state, display on screen is as follows:
Edit Area, one line shows data of two point .
SEQ: 01 – it means current set patrol 1
CLOE: EXIT – push CLOSE to exit edit state
10 3

1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
1 2 3 4 5 6
DIP ON
1 2 3 4 5 6 7 8 9 10
DIP ON
II. INTRODUCTION OF FUNCTIONS
1. Unlimited rotation 360° horizontally and from +33° to -80° vertically.
2. The horizontal speed is 0 - 40°/sec while the vertical speed is 0 - 20°/sec (wind speed less
than 50 miles/hour).
3. At the preset position, the horizontal speed is 0 - 100°/sec while the vertical speed is 0 - 40°/
sec (wind speed less than 50 miles/hour).
4. Automatic control of constant temperature, manual rain wiper/defroster control.
5. IP grade IP66.
6. The bearable maximum wind speed is 130 miles/hour.
7. 128 preset positions in memory and 6 groups of programmable patrol loci, as well as linear
scan between two points with adjustable speed and variable direction,
8. 16 common protocols integrated, four kinds of baud rate 2400/4800/9600/19200 bps available
and 1024 addresses are supported (0 - 1023).
III. QUICK GUIDE OF INSTALLATION
1. Modify the Protocol and the Address (jump over this section if no modication)
Remove the small metal cover on the bottom shown as dotted-lined part on Figure 3.1.1 to
expose DIP switch of the address and the protocol shown as Figure 3.1.2. The detailed draw-
ing is shown as in Figure 3.1.1.
Shown as Figure 3.1.3, the 10-bit DIP stands for the addresses which can be from 0 to 1023.
The 6-bit DIP stands for the protocols in which bits 1-4 mean the protocol while bits 5-6 means
the baud rate. Push the DIP downward means ON otherwise it means OFF. For example
the address in the gure means 1 while the protocol means PELCO-D with the baud rate of
2400bps which can be found from the table.
Shown as Figure 3.1.3, the 10-bit DIP stands for the addresses which can be from 0 to 1023.
The 6-bit DIP stands for the protocols in which bits 1-4 mean the protocol while bits 5-6 means
the baud rate. Push the DIP downward means ON otherwise it means OFF. For example
the address in the gure means 1 while the protocol means PELCO-D with the baud rate of
2400bps which can be found from the table.
The top line and the bottom line display prompt message, and the middle area displays infor-
mation of each locus, one line shows data of two points. Move the cursor by PAN LEFT/RIGHT
and modify data by TILT UP/DOWN. Press the button down for 1 second to accelerate. Press
CLOSE button to exit the edit state and store modication. In above gure, the program stores
four patrol points. The settable range of POS is from 1 to 63 or 65 to 128. In case POS is “---“,
it means the skip this point. The settable range of SP is from 0 to 8 (0 and 1 are same at the
highest speed while grade 8 has the lowest speed). The settable rage of TM is from 0 to 99
seconds.
Operation of the Title of Preset under Edit State
After entering into the edit state, the screen show as
the drawing. You can nd current setup is the preset 1
with the title “NO TITLE”. Move the cursor by PAN LEFT/
RIGHT and modify data by TILT UP/DOWN. Press the
button down for 1 second to accelerate. Press CLOSE
button to exit the edit state and save modication. The
title of preset can contain 8 characters such as 0~9, A~Z,
+, - and blank. Note: the rst letter should be 0~9 or A~Z
otherwise it means to delete the title of the presets and it
shall only show “NO.XXX” without the title when preset
points.
V. SPECIAL OPERATION
The preset 51 to 60 are used for special functions. It has special meanings to set or call these
points. Therefore these points should not be used in functions of automatic operation of the
pan/tilt such as multiple points patrol, external alarm linkage etc. so as to avoid error actions.
Preset Set Preset Call Preset
51 Wiper ON Wiper OFF
52 Defroster ON Defroster OFF
53 Auxiliary Output AC24V ON Auxiliary Output AC24V OFF
54 Linkage of External Alarm 1 ON Linkage of External Alarm 1 OFF
55 Linkage of External Alarm 2 ON Linkage of External Alarm 2 OFF
56 Reserved Reserved
57 Reserved Reserved
58 Reserved Reserved
59 Reserved Reserved
60 Reserved Reserved
Figure 3.1.1 Figure 3.1.1 Figure 3.1.3
211

I. NOTES FOR ATTENTION
1. Read the manual carefully before installing the product.
2. Power Supply: 220V/110V/24V, refer to the sticker on the product.
3. Avoid incorrect shipping methods such as overstacking or strong vibration during the course
of transportation, storage and installation, as the product could be damaged.
4. Do not dismount components inside the product to avoid occurrence of trouble. There are no
user serviceable parts inside the camera.
5. Observe all electric safety standard in use and installation and use power supply attached
to the product. RS-485 and video signal should keep enough distance with the high voltage
devices and cable during the course of transmission, and take protection measures such as
anti-lightning and surging if necessary.
6. Do not use the product under conditions which exceeds the temperature, humidity or speci-
cations of power supply.
7. Do not aim the camera at the sun or very bright object or to monitor bright and still object,
whether the power supply is switched on or off.
8. Do not clean the product with strong or abrasive detergent. Clean out dirt with dry cloth or mild
detergent if dirt is not easily removed.
9. Take care to set up the product to avoid collision or vibration. Improper application can cause
damage.
10. Install the product in a location that is capable of supporting the Camera PTZ system weight.
11. Wipe dust on the lens with special lens paper.
WARNING:
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufcient magnitude to consti-
tute a risk of electric shock to persons.
SPECIFICATIONS
Model GV-SCS530
Image sensor 1/4” EX view HAD CCD
Number of total pixels Approx. 380,000 pixels
Lens 36x optical zoom,f=3.4 mm(wide)to 122.4 mm (tele), F1.6 to F4.5
Digital zoom 12x (432x with optical zoom)
Angle of view (H) 57.8° (wide end) to 1.7° (tele end)
Minimum object distance 320 mm (wide end) to 1,500 mm (tele end)
Sync system Internal / External (V-lock)
Minimum illumination 1/60s mode: 1.4 lux (typical)(F1.6, 50 IRE): 1/4s mode: 0.1 lux (typical)(F1.6, 50 IRE)
Horizontal Resolution 530TV Lines
Day & Night Yes, True D/N, IR Cut Filter Removal
S/N ratio More than 50dB
Electronic shutter 1/1 to 1/10,000s, 22 steps
White balance Auto, ATW, Indoor, Outdoor, One-push, Manual
Gain Auto / Manual (-3 to 28 dB, 2 dB steps)
AE control Auto, Manual, Priority mode (shutter priority & iris priority), Bright, EV compensation, Backlight
compensation, Slow AE
Wide Dynamic Range On / O: Wide-D, 128x
Backlight compensation On / O
Privacy zone masking On / O (8 masks per view/24 masks presets in the entire viewing range when integrated into a PTZ
camera - 14 colors, mosaic)
Character generator Mode display/Multi-line OSD (OSD has priority over Mode display)
Flicker cancel Auto
Focusing system Auto (Sensitivity: normal, low), One-push AF, Manual, Innity, Interval AF, Zoom Trigger AF
Picture eects E-Flip, Black & White, Mirror Image, Picture Freeze, Mirror
Image
Camera operation switch Zoom tele, Zoom wide
Video output VBS: 1.0 Vp-p (sync negative), Y/C
Dimensions (WxHxD) 16.14 x 13.38 x 6 in / 410 x 340 x 152 mm
Pan Preset speed 100°/s (wind speed low 50 mile/hour)
Tilt preset speed 30°/s (wind speed low 50 mile/hour)
Pan speed 0°~40°/ S
Tilt speed 0°~20°/ S
Pan range 360° continuously
Tilt range +33° ~-80°
Preset, track 128 presets, 6 tracks
Control way Multi-protocol, Baud rate from 2400Bps to 19200Bps, RS485 Control
Operating Temperature -35° ~ 55°C / -31° ~ 131° F
Relative humidity 90% Non Condensing
IP grade IP66
Power supply 24VAC
Power consumption 70VA
Weight 23.1 lb / 10.5 Kg
Protocols Pelco P, D, SAMSUNG
RISK OF ELECT RI C SHOCK
DO NOT OPE N
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK. NO
USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
CAUTION:
To prevent electric shocks and
risk of re hazards do NOT use
other than specied power
source.
12 1

SUMMARY
The “Smart Camera System” GV-SCS530 is a high-performance, integrated positioning sys-
tem featuring a 530TV Lines resolution, 36x optical zoom camera, lens and complete PTZ unit.
Made from die-cast aluminum construction, with an IP66 rated weather-resistant design. The
GV-SCS530 has a built-in heater, wiper, window defroster, sun-shield, anti-fogging, dust-proof
and frost protection function. It can withstand high winds, offers complete 360-degree panning
with tilt ranges of +33 degrees and -83 degrees from the horizontal. What’s more, the camera is
equipped with a number of convenient functions such as Spherical Privacy Zone Masking with
Mosaic Effect, Video Motion Detection, Multi-Line On-Screen Display, E-ip, and Picture Freeze.
The GV-SCS530 is also compatible with many popular control protocols.
FEATURES
• 1/4 Inch type ExView HAD CCD
• 530TV Lines Resolution
• Minimum Scene Illumination: 1.4 lux @ 1/60s shutter speed, 0.1 lux @ 1/4s shutter speed
• 36x Optical Zoom (12x Digital zoom, 432x total)
• True Day/Night with IR Filter Removal
• Wide Dynamic Range
• E-ip
• Picture Freeze
• Advanced Spherical Privacy Zone Masking Function with Mosaic Effect
• Video Motion Detection
• Multi Line On-Screen Display
• Electronic shutter / slow shutter
• Internal / External synch (V-lock)
• Die-cast Aluminum construction, high temperature resistant
• Weather resistant, dust proof design, protection grade IP66
• 360° continuous panning
• Tilt range +33°~-80°
• Auto pan function between 2 presets
• 128 presets 6 tracks
• Anti fogging and frost protection function
• Wiper
• Factory presets
• Register set command
• RoHS-compliant
• Multi Protocol Control
• Included Wall Mount
NoTES

GVI Security
2801 Trade Center Dr., Suite 120 • Carrollton, TX 75007 • Toll Free: 888-595-2288 • www.gviss.com
GVI Security
2801 Trade Center Dr., Suite 120 • Carrollton, TX 75007 • Toll Free: 888-595-2288 • www.gviss.com
GV-SCS530 Users Manual
v.11.06.08
INTEGRATED PTZ POSITIONING
SYSTEM, 36X OPTICAL ZOOM, WDR,
D/N, INDOOR OUTDOOR CAMERA
before installing and using the camera, please read these instructions
thoroughly and retain them for later reference.