CIS VISION:elite VCC-G60FV11GE Quick start guide

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
5M Pixel B/W Gig-E Camera
VCC-G60FV11GE
Product Specification
& Operational Manual
CIS Corporation
English

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
2
Table of Contents
1. Scope of Application.......................................................................................................................... 3
2. Handling Precautions ........................................................................................................................ 3
3. Product Outline................................................................................................................................. 4
4. Specification..................................................................................................................................... 5
4.1. General Specification .................................................................................................................. 5
4.2. Camera Output Signal Specification.............................................................................................. 7
4.3. CCD Spectral Response (Representative Value) ............................................................................. 8
4.4. Image output format (Coyote Application Setting)......................................................................... 8
5. Function Settings .............................................................................................................................. 9
6. External Connector Pin Assignment ...................................................................................................11
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) ..................................................................11
6.2. RJ-45 Gigabit Ethernet Connector MOD-YSJ88DA03C-CN+ (HONDA TSUSHIN KOGYO CO., LTD) .....12
7. Timing Chart....................................................................................................................................13
7.1. Horizontal Synchronous Signals Timing........................................................................................13
7.2. Full Frame Scan Mode Timing .....................................................................................................13
7.3. Standard Trigger Mode Timing ....................................................................................................14
7.4. Pulse Width Trigger Timing .........................................................................................................15
8. Partial Scan Mode Details .................................................................................................................16
9. Remote Interface Function ...............................................................................................................17
10. Initial Settings ...............................................................................................................................18
11. CCD Optical Axis Accuracy ..............................................................................................................19
12. Dimensions....................................................................................................................................20
13. Cases for Indemnity (Limited Warranty)...........................................................................................22
14. CCD Pixel Defect ............................................................................................................................23
15. Product Support.............................................................................................................................23

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-G60FV11GE, 5M pixels Gig-E B/W CCD Camera. All specifications contained herein
are subject to change without prior notice. Reproduction in whole or in part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply
to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
Do not use or store the camera in the following extreme conditions:
Extremely dusty or humid places.
Extremely hot or cold places (operating temperature –5℃to +40℃)
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Places subject to fluorescent light reflections.
Places subject to unstable (flickering, etc.) lighting conditions.
Places subject to strong vibration.
Remove dust or dirt on the surface of the lens with a blower.
Do not apply excessive force or static electricity that could damage the camera.
Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
Follow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
Confirm the mutual ground potential carefully and then connect the camera to monitors or computers.
AC leaks from the connected devices may cause damages or destroy the camera.
Do not apply excessive voltage.(Use only the specified voltage.) Unstable or improper power supply
voltage may cause damages or malfunction of the camera.
The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
The rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoide noises like chattering when rising.

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
4
2ch output, separated into right and left, CCD is utilized for VCC-G60FV11GE. Image signals for
right half screen and left half screen are output via each independent circuit. Therefore, differences
between right screen and left screen could be seen depending on the usage conditions (shooting
conditions /temeperature conditions and so on). CIS trys its best to adjust this differences but please
be noted it would not be perfect.
In case of abnormal operation, contact the distributor from whom you purchased the product.
3. Product Outline
VCC-G60FV11GE is a Gigabit Ethernet interfaced, high-resolution industrial black and white video camera
module utilizing a 2/3 type PS IT CCD. 5M pixels CCD image sensor with on-chip micro-lenses realizes high
sensitivity and high resolution. At Full Frame Scan Mode, entire pixels can be read out within approx. 1/15s.
Features
□High speed communication, maximum 108MB/s. (Comform to 1000BASE-T)
□The maximum transmission distance is approx. 100m with cable more than CAT5e.
□Camera settings can be set via LAN.
□Software trigger input via LAN or hardware trigger input via 12pin connector at rear is selectable.
□Shutter speed can be set from 1/15sec ～1/30,000sec by 1H.
□At partial scan mode, both capturing start position and capturing width can be set by 3H.
Bundled Items
□Camera
□iPORT Software Development Kit 2.4.1 build 921. ※
□Gig-E Camera Control Software (CamCtlSetup.exe). ※
□Start up manual ※
※Please ask for the details or download it from our web.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms ]
9
8
7
60 70
Power Supply Voltage

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
5
4. Specification
4.1. General Specification
Item
Specification
Pickup device
Device Type
2/3 type Interline Transfer B/W CCD, Sony ICX625ALA
Effective Pixel Number
2456 (H) x 2058 (V)
Unit Cell Size
3.45μm (H) x 3.45μm (V)
Chip Size
9.93mm (H) x 8.70mm (V)
Videooutput frequency
Pixel Clock
60 MHz
Horizontal Frequency
31.185 KHz Pixel Clock: 1924CLK
Vertical Frequency
Full Frame Scan Mode: 2079 lines, approx 15.000Hz
Sync. system
Internal Sync. System
Video output standard
Gigabit Ethernet (Comform to 1000BASE-T) Trasferring speed: 108MB/s (max)
Resolution
2058 TV lines
Resolving power
8bit / 10bit (Note; Real time output is invalid at 10 bit output.)
Sensitivity
F 5.6 400 lx (Shutter speed 1/15s, Gain 0dB)
Minimum illumination
F 1.4 1 lx (Shutter speed 1/15s, Gain Max +18dB)
Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
Power requirements
DC +12V ±10% (Max voltage not to exceed +15V)
Power consumption
5.8 W (At DC +12V IN, normal mode, and full frame scan mode)
6.0W (At DC +12V IN, normal mode, and partial scan mode)
Dimension
Refer to overall dimension drawing (Clause 12)
55mm x 55mm x 60mm (excluding projection)
Mass
Approx. 190 g
Lens mount
C mount (Refer to overall dimension drawing)
Optical axis accuracy
Refer to drawing for CCD Optical Axis Accuracy (Clause 11)
Gain variable range
0～+12dB (Analog Gain; over 0dB～+6dB, Digital Gain; 0dB～+6dB)
Shutter speed
variable range
1/15s (Off) ～1/30000s
Trigger shutter mode
・Standard Trigger Mode ・Pulse Width Trigger Mode

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
6
Item
Specification
Safety/Quality
standards
UL: Conform to UL Standard including materials and others.
RoHS: Conform to RoHS
CE: EN 55022:2006 (Class A) for Emission
EN 61000-6-2:2005 for Immunity
FCC: To be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Durability
Vibration
Acceleration
98 m/s2(10.0G)
Frequency
20～200 Hz
Direction
XYZ 3 directions
Testing time
120 min for each direction
Shock
No mulfunction shall be occurred with 980m/s2(100G) for ±X,
±Y, and ±Z, 6 directions. (without package)
Operation environment
Temperature
Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temeprature: -5℃～+45℃
※All the specifications specified in this manual is guaranteed
under performance guaranteed temperature.
※All the camera functions operate normally under operation
guaranteed temperature
Humidity
RH 20～80% with no condensation
Storage environment
Temperature
-25℃～+60℃
Humidity
RH 20～80% with no condensation
Recommended System
LAN Card
Intel PRO/1000 series
LAN Cable
MOD-YSP-A1AS-SP series (Honda Tsushin Kogyo)
MV series (CEI)
OS
Windows XP, Windows VISTA
Memory
Over 512 MB (over 1GB recommeded)

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
7
180Ω
TTL In(a)
VCC
+3.3V
TTL Out(b)
※(a):0～3
(b):0～2
180Ω
220KΩ
6.6V
6.6V
UDZS TE-17 6.2B
(ROHM)
SN74LV125A(TI)
Vih : Vcc × 0.7(Min)
Vil : Vcc × 0.3(Max)
Voh : 2.48V(Min)
Vol : 0.44V(Max)
4.2. Camera Output Signal Specification
Item
Specification
Video output
data
Video out
2456 (H) x 2058 (V)
At Full Frame Scan Mode
60MHz 2Tap output
Sync. Signal
I/O
LVAL output
LVTTL (3.3V Output)
HR10-10R-12PA
FVAL output
LVTTL (3.3V Output)
※Output pin assignment is
set via iPort SDK. Please
refer to our VCC-G60/F60
GE series startup manual,
section 5.7. Trigger Mode.
DVAL output
LVTTL (3.3V Output)
SP (Exposure Signal)
LVTTL (3.3V Output)
Trigger input
Polarity
POSI/NEGA Selectable
Trigger Pulse width
Min. over 2 HD ～Max. under 4158 HD
Hardware Trigger input
LVTTL (5.0V Tolerant)
HR10-10R-12PA
Software Trigger input
RJ-45
Video output
signal
White Clip Level
Digital 8bit
: FFh
Setup Level
Digital 8bit
: 08h±04h
Dark Shading
Digital 8bit
: Under 08h for both horizontal and vertical
(Conditions: Gain 0dB)
Leval differences
between right and left
Digital 8 bit
: Under 03h (Conditions: Gain 0dB)
※5 secounds shall be waited after turning on power to get proper camera operation.
12 pins circular connector at rear GPIO interface

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
8
4.3. CCD Spectral Response (Representative Value)
※Lens charcteristics and luminous source charcteristics are not considered.
4.4. Image output format (Coyote Application Setting)
・2-Taps , Segmented, Dual Left + Right Inverted Output
・Area of interest Width : 2456 Height : 2058 Offset X : 0 Offset Y : 12

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
9
5. Function Settings
Camera functions can be set with serial communications.
Function
Address
Data
Gain
001
0:
0 dB: Analog Fixed Gain
1:
+3 dB: Analog Fixed Gain
2:
+6 dB: Analog Fixed Gain
3:
+12 dB: Analog Gain (+6dB) + Digital Gain (+6dB)
4:
Manual Gain (Refer to Address 005, 006, 007, and 008)
E-Shutter
002
0:
1/15s(Off)
1:
1/30s
2:
1/60s
3:
1/90s
4:
1/120s
5:
1/150s
6:
1/200s
7:
1/250s
8:
1/500s
9:
1/750s
10:
1/1000s
11:
1/2000s
12:
1/5000s
13:
1/10000s
14:
1/15000s
15:
1/30000s
16:
Manual Shutter (Refer to Address 009 & 010)
Trigger Mode
004
0:
Normal Mode (Trigger Mode Off)
1:
Standard Trigger Mode (Shutter speed can be set with address 002.)
2:
Pulse Width Trigger Mode (Shutter speed can be set with trigger pulse width.)
Manual Analog Gain (Right)
005&006
0～512:
0: 0dB～512: over +12dB (Log Linear)
※Set the address 001 data to 004.
Manual Analog Gain (Left)
007&008
0～512:
0: 0dB～512: over +12dB (Log Linear)
※Set the address 001 data to 004.
Manual Shutter Control
009&010
0～2078:
1/15s (Off)から1/36058s
※Set the address 002 data to 016.
Address 009 MSB and address 010 LSB makes total 16 bit.
Shutter speed = (2078-(009&010)) x 32.07μs + 27.73μs
Max data = 2078
Trigger Polarity
011
0:
Positive Input
1:
Negative Input
Output Data Select
013
0:
8bit Output Data
1:
10bit Output Data
Gamma Mode
014
0:
Gamma Off (1.0)
1:
Gamma On
Partial Scan Mode
015
0:
Full Frame Scan Mode
1:
Partial Scan Mode

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
10
Function
Address
Data
Partial Scan Start Position
016&017
0～685:
Set the address 015 data to 001.
Address 016 MSB and address 017 LSB makes total 16 bit.
Start Position: 3 H/step Min Data: 0 (0H)/Max Data : 685 (2055 H)
Start Position (016&017)+ Effective Line (019&020) <= 685
Partial Scan Effective Line
019&020
0～684:
Set the address 015 data to 001.
Address 019 MSB and address 020 LSB makes total 16 bit.
Effective Line: 3 H /step Min Data: 0 (3 H)/Max Data : 685 (2058 H)
Start Position (016&017)+ Effective Line (019&020) <= 685
Partial Scan Total Line
021&022
0～2078:
Read Only
Total line number at Partial Scan Mode or Full Frame Scan Mode minus 1 is set
Manual Digital Gain (Right)
126&127
256 ～
512:
256: x1(0dB)～512: x2(+6dB)
※Set address 001 data to 004.
Manual Digital Gain (Left)
128&129
256 ～
512:
256: x1(0dB)～512: x2(+6dB)
※Set address 001 data to 004.
Data Save
255
Input 083 or 053 to save the data in EEP-ROM.
Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
11
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE)
TTL In(a) a:0～3・・・Trigger Input etc.
TTL Out(b) b:0～2・・・LVAL, FVAL, DVAL, SP, Pulse Generator etc.
※Pin assignment and functions can be set arbitrarily via iPORT software.
Please refer to iPORT.Software.Coyote.pdf in￥Program Files￥Pleora Technologies Inc￥iPORT
Software￥Documentation.
Pin
No.
Signals which can be controlled by GigE
Camera Control Software
1
GND
2
Power In DC +12V
3
TTL In3
(LVTTL Input 5V Tolerant)
Trigger Input
4
TTL Out2
(LVTTL 3.3V Output)
LVAL, FVAL, DVAL ,SP(Exposure) Output
5
GND
6
TTL In2
(LVTTL input 5V Tolerant)
Trigger Input
7
TTL Out1
(LVTTL 3.3V Output)
LVAL, FVAL, DVAL ,SP(Exposure) Output
8
TTL In1
(LVTTL input 5V Tolerant)
Trigger Input
9
TTL Out0
(LVTTL 3.3V Output)
LVAL, FVAL, DVAL ,SP(Exposure) Output
10
TTL In0
(LVTTL Input 5V Tolerant)
Trigger Input
11
NC
12
NC

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
12
LINK(Green LED) ACT( Yellow LED)
6.2. RJ-45 Gigabit Ethernet Connector MOD-YSJ88DA03C-CN+ (HONDA TSUSHIN KOGYO CO., LTD)
LINK LED: Lighting-off ・・・Unconnected to LAN
Lighting-on ・・・Connected to LAN
Blinking ・・・Transmitting the data
ACT LED: Lighting-off ・・・Unconnected or connected with 10Mbps/100Mbps
Lighting-on ・・・Connected with 1000Mbps

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
13
LVAL Output
696 CLK
Video Output
DVAL Output
696 CLK
FVAL Output
1924CLK
1228CLK
CLK =60MHz
2 Tap Output
1 CLK
LVAL Output
Video Output
DVAL Output
FVAL Output
1 2 3 4 5 6 7 8 9 1020762075 11 12 21 23 24
(CCD Read Out Signal)
9 H
21 H2058 H
12 H
Total = 2079H
207920782077
2058 H
22
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing
7.2. Full Frame Scan Mode Timing

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
14
LVAL Output
Video Output
FVAL Output
DVAL Output
12H
TTL IN(a)
(CCD Read
Out Signal)
1 9
22 2079
2058H
2070H
(Trigger Input)
Exposure Time
TTL IN(a)
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
SP Output
(Exposure Signal)
a
b
3
CLK
81
CLK
a
b
1.40μs
CLK60MHz
nHD × 32.07μs+27.73μs
Delay(Fixed)
※(a):0～3
7.3. Standard Trigger Mode Timing
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to the start of exposure, is 1.40μs at RAW mode.
□Trigger input can be accepted even when the camera is outputting video signals. However, a shutter
timing, to start the next video output before completion of transferring video output for the prior signals,
can not be worked. To input trigger signals when the camera is outputting video signals for the prior
signals, it shall be synchronized with the down edge of camera LVAL output.
□Trigger input during the execution of exposure (exposure time) shall be ignored. (Refer to the “G”below.)
(E)
（Ｂ）
（Ｂ）
(F)
Trigger Invalid
(E)
（Ｆ）
(F) (G)
✖
Standard Trigger Mode
Video Output
TTL IN(a)
(Trigger Input)
DVAL Output
SP Output
(Exposure Signal) Exposure Time (Register Set Value) Exposure Time (Register Set Value)
(Exposure Time)
✖

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
15
LVAL Output
Video Output
FVAL Output
DVAL Output
12H
TTL IN(a)
(CCD Read
Out Signal)
1 9
22 2079
2058H
2070H
(Trigger Input)
Exposure Time
TTL IN(a)
(Trigger Input)
(Sub Pulse)
(CCD Read Out Signal)
SP Output
(Exposure Signal)
a
b
3
CLK
81
CLK
1216
CLK
a
b
532
CLK
Delay(Fixed)
Delay(Fixed)
1.40μs
CLK60MHz
29.13μs
※(a):0～3
7.4. Pulse Width Trigger Timing
□Trigger operation is CLK sync, V-Sync Reset.
Delay time, from detecting the trigger edge to the start of exposure, is 1.40μs. Delay time, from
detecting the trigger edge to completion of exposure, is 29.13μs.
□Trigger input can be accepted even when the camera is outputting video signals. However, a shutter
timing, to start the next video output before completion of transferring video output for the prior signals,
can not be worked. Please refer to the “C”below. To input trigger signals when the camera is
outputting video signals for the prior signals, it shall be synchronized with the down edge of camera LVAL
output.
(A)
(A) (B)
（Ｂ）
(B)
(C)
（Ｂ）
(D)
(D)
Trigger Invalid
Pulse Width Trigger Mode
✖
Video Output
TTL IN(a)
(Trigger Input)
DVAL Output
SP Output
(Exposure Signal)
Exposure Time
(Pulse Width)
Exposure Time
(Pulse Width)
Exposure Time
(Pulse Width)
(Video Output (C))
✖
(Exposure Time)

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
16
LVAL Output
(Normal Scan)
9 H
Video Output
(Normal Scan)
2079 H
VIDEO Output
(Partial Scan)
LVAL Output
(Partial Scan)
9 H
12 H
Total Line(Address 021&022) + 1H
2058 H
Y Offset
12H + Starting Position
(Address016&017)
Effective Line
(Address 019&020)×3+3H
High Speed
Transmit Term
High Speed
Transmit Term
8. Partial Scan Mode Details
Capturing start position and capturing width can be set by 3H via LAN.
Reading out position register (Address 016 & 017): 0(0H) ~685(2055H) 3H/step
Effective line register (Address 019 & 020): 0(3H) ~685(2058H) 3H/step
Total line register (Address 021 & 022): 706Lines + (Effective line register × 2) + 2 (Read Only)
Note: Reading out position and effective line shall meet the following condition.
Reading out position register + Effective line register = < 685
Otherwise, the value, 685 –reading out position register, will be set to the effective line register.
<Example 1> Conditions: Reading out position register (Address 016 & 017) = 000
Effective line register
(Address 019&020)
Effective Lines
Total Lines register
+1 H
Frame rate
0
3 H
709 H
44 fps
・
・
・
・
159
480 H
1027 H
30 fps
・
・
・
・
255
768 H
1219 H
26 fps
・
・
・
・
341
1026 H
1391 H
22 fps
・
・
・
・
399
1200 H
1507 H
21 fps
・
・
・
・
685
2058 H
2079 H
15 fps

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
17
9. Remote Interface Function
Through LAN, the camera can be controlled.
(1) The settings for RS-232C
(2) Control code
・The total control code is 14 bits, which conforms to ASCII code.
・The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1
2
3
4
5
6
7th Byte
8
9
10
11
12
13
14
Camera No.
Process code
Remote controller
address
Remote controller data
CR
000000: fixed
“R”Read mode
Please refer to the
address table of
Section 5. Function
Settings.
000～255
0 Dh
“W”Write mode
“C”Camera mode
Camera No. is fixed with 6 bite numerical strings, “000000”.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall
consists of 14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Section 5. Function Settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.
Baud rate
:9600bps
Data
:8bit
Stop bit
:1bit
Parity
:None
XOn/XOff
:Not controlled

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
18
Remote controller address
Note: Do not write the data into the address other than specified, since it may cause
the damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read control mode.
CR
Be sure to input “CR”to confirm the end of the command.
※Note: When setting the data with 2 Byte, High Byte shall be set first, then Low Byte to the next.
The camera rewrites the internal resister when receiving Low Byte.
10. Initial Settings
Function
Address
Data
Gain
001
0: 0dB
E-Shutter
002
0: 1/15s (Off)
Trigger Mode
004
0: Normal Mode (Trigger Mode Off)
Trigger Polarity
011
0: Positive Input
Output Data Select
013
0: 8 bit Output Data
Partial Scan Mode
015
0: Full Frame Scan Mode
Partial Scan Total Lines
021 & 022
2078: Read Only

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
19
Datum Plane B
55
55
Inclination of optical
axis to datum plane B.
Inclination of optical
axis to datum plane A.
Datum Plane
A
6.3
6011.1
Datum plane A
910-003-00-00
*)Dimensions from datum plane A to the center of lens mount.
The center of effective pixels
shall be within f 0.6??
to the center of lens mount.
Inclination of effective pixels ?
to datum plane A shall be
??±0.5°
(Unit:mm)
90°±0.2°
Under±0.5°
?±0.5°
27.5±0.3(*)
11. CCD Optical Axis Accuracy

VCC-G60FV11GE Rev.900-665-32-00
©2010 CIS Corporation. All rights reserved.
20
28±0.1
28±0.1
55
55
Under R1
60 6.3 11.1
Product Name
Label Position
35±0.1
4.5±0.1 52
GigE DC IN
ACT
LINK
999-500-00-00(1/2)
*2) Screw length from C mount lens surface shall be under 6mm. And protruding portion shall be
lesss than 10mm.
*1) C Mount screws comply with ANSI/ASME B1.1, 1-32UN(2B).
(Unit:mm)
F 29 0
-0.05
4-M3
Depth 4
4-M3
Depth 4
CMount(*)
5 MEGA PIXEL
12. Dimensions