Lucasey PCEC1417A User manual

Philips monitor & base not
included with PCEC1417A
14"
Steps 1-4
(8 PL.) VHB Adhesive Tape, 1 sq. in.
PCEC1417A Bottom Plate
Step 5
1. Determine the appropriate location on the furniture for the
monitor. Mark a parallel line at the front edge of the Philips
monitor base. Mark a second parallel line 8-1/4" back from
the previous line.
2. Clean the furniture surface 2x with an alcohol wipe to
remove any residue on the furniture surface.
3. Peel the plastic liner from the Adhesive Tape on the Bottom
Plate. Avoid any accidental contact between the exposed
adhesive and any objects.
4. Carefully line up the front edge of the Bottom Plate with
the second line marked in step 1.
5. Press the PCEC1417A Bottom Plate down putting pressure
on each of the eight Adhesive Tape Locations.
Component List
PCEC1417A Top Plate
PCEC1417A Bottom Plate
.400" Dia x .150" Tall Plastic Adhesive Buttons
1 ...
1 ...
4 ...
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
PCEC1417A INSTALLATION INSTRUCTIONS Page 1 of 3
©2010 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
PCEC1417A - Adhesive Furniture Mount
Important! Please read all warnings and cautions before installing the mount.
Caution: Improper installation of this mount may void the warranty on your monitor.
Caution: Installation should be performed by qualified installers only, using construction methods prescribed
by authorized architects or engineers that comply to all applicable codes and standards.
The maximum weight of monitor to be installed on the PCEC1417A is 50lbs (22.7 kg)
Inspect all parts to make sure there is no shipping damage. Do not install if any parts are damaged.
Please call 1-800-LUCASEY or 1-510-534-1435 if you have any questions about this installation.
PCEC1417A (05/2010)
for Philips Models: 32HF5581, 37HFL5682L/F7
& 42HFL5682L/F7

(3 PL.) Philips Plastic Insert
Step 6
(3 PL.) Philips display screw
Step 7
PCEC1417 Top Plate
Step 8
4Pl. Replace Feet on 37" or 42" Base with
the provided .4" dia. x .15" tall rubber feet
Philips 37" 37HFL5682L/F7 or
42" 42HFL5682L/F7 Base
Step 10
Step 9
6Pl. 37" & 42" Base Installs Only: Add Feet
to PCEC1417 Top Plate with the provided .4"
dia. x .15" tall rubber feet
6. Remove the three screws from the bottom of the Philips Display Base
and set aside for later use. Leave the three plastic inserts in the holes.
7. Confirm that the plastic inserts that came with the display are still in the
holes. Align the holes in the PCEC1417B Top Plate with the holes in the
display base, placing the raised portions of the PCEC1417B Top Plate
against the display base. Use the the three screws that came with the
display to fasten the PCEC1417B Top Plate onto the display base.
Philips 32" 32HF5581 Base Installation
8. Remove the three screws from the bottom of the Philips Display Base
and set aside for later use. Leave the three plastic inserts in the holes.
Replace the 4 Rubber Feet on the 37" or 42" Philips Base with 4 of the 10
provided Rubber Feet in the locations shown.
9. Add 6 of the 10 provided Rubber Feet to the PCEC1417 Top Plate in the
locations shown.
10. Confirm that the plastic inserts that came with the display are still in
the holes. Align the holes in the PCEC1417B Top Plate with the holes in the
display base, placing the raised portions of the PCEC1417B Top Plate
against the display base. Use the the three screws that came with the
display to fasten the PCEC1417B Top Plate onto the display base.
Philips 37" 37HFL5682L/F7 or
Philips 42" 42HFL5682L/F7
Base Installation
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1 Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
PCEC1417A INSTALLATION INSTRUCTIONS Page 2 of 3
©2011 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com PCEC1417A (08/2011)

PCEC1417K Release Key
Align the Release Key slightly off-center as shown and slide between the
Top Plate Assembly and the Bottom Plate.
Once the Release Key is inserted all the way, the top and bottom plates
will release from each other by lifting up and back with the monitor
attached to the PCEC1417B Top Plate.
Monitor Release
Step 11
11. Align the slots on the Top Plate Assembly with the rivets on the Bottom
Plate and pull forward on the Top Plate Assembly to lock the two plates
together. Double check that all of the rivets have properly seated by lifting
up on the corners of the Top Plate Assembly and by pushing the Top Plate
Assembly back.
Note: Do not align the Top Plate Assembly with the monitor attached to the
monitor base.
Attach the AOC Monitor to the Monitor Base. Follow the manufacturer's
instructions for attaching the Monitor Base to the AOC Monitor, using the
screws that came with the monitor.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
©2011 0 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com PCEC1417A (08/2011)
PCEC1417A INSTALLATION INSTRUCTIONS Page 3 of 3