Lucasey TH100200W User manual

TH100200W Wall Plate
3Pl. #14 x 2-1/2" Lag Screws
(For metal stud walls, use WMATB3 toggle bolt kit
for concrete walls, use WMAAB3 anchorbolt kit,
sold separately)
Wall Plate Installation
5/16"-18 x 1-7/8"
Hex Flanged Head Screw
5/16"-18 Nylock Nut
5/16" Flat Washer
5/16" Belleville Washer
(Curved Side Facing Down)
Wall Arm Installation
3Pl. 5/16" Belleville Washer
(Curved Side Facing Up)
1 ...
1 ...
1 ...
1 ...
1 ...
1 ...
1 ...
1 ...
2 ...
1 ...
4 ...
3 ...
4 ...
6 ...
4 ...
4 ...
4 ...
Component List
TH100200W Wall Plate with Knuckle
TH100200W 6" Projection Wall Arm
TH100200W 3-1/2" Projection Wall Arm
TH100200W 100/200mm Adapter
TH100200W 75/100mm VESA Plate
5/16"-18 x 1-7/8" Hex Flanged Head Screw
5/16"-18 x 2" Hex Button Head Screw
1/4"-20 x 2" Hex Button Head Screw
5/16"-18 Nylock Nuts
1/4"-20 Nylock Nut
5/16" Flat Washers
1/4" Belleville Washers
5/16" Belleville Washers
6mm x 12mm Phillips Pan Head Screws
1/4" Flat Washers
8mm x 20mm Phillips Pan Head Screws
8mm Flat Washers
Wall Plate Installation
Measure from the floor and ceiling to the centerline for
where the screen needs to be mounted on the wall.
Make sure that appropriate clearance under the screen is
maintained by subtracting the distance from the bottom
of the screen to the center of the VESA mounting pattern.
Align the center of the TH100200W Wall Plate with the
centerline measurement for the screen. Use the
TH100200W Wall Plate as a template to mark the
locations to drill pilot holes. Make sure that the
TH100200W Wall Plate is level while marking the
pilot hole locations.
For wood studs, drill 1/8" holes 2-1/2" deep. (For metal
studs & concrete anchor bolts, consult the appropriate
fastener installation guide for the hole diameter needed)
Attach the TH100200W Wall Plate with the provided
#14 x 2-1/2" Lag Screws.
Adjust the TH100200W Wall Plate level and tighten
all 3 screws.
Wall Arm Installation
Attach the TH100200W Wall Arm to the TH100200W
Wall Plate with the 5/16"-18 x 1-7/8" Flanged Head
Screw, Washers & Nylock Nut as shown in the
illustration.
Tighten the pivot screw for the desired pivoting tension.
Note: The curved 5/16" Belleville Washers should be
installed with the curve facing towards the welded
knuckle (Top washer facing down and bottom washers
facing up) to facilitate smooth pivoting action.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
TH100200W INSTALLATION INSTRUCTIONS Page 1 of 3
©2013 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
TH100200W Wall Mount Installation
TH100200W_Ins (5/13)

THDVDW1217 Adapter
(Sold Separately)
TH100200W 100/200mm
Adapter Plate
TH100200W 75/100mm
Plate
4Pl. Acorn Nuts
4Pl. Washers
4Pl. #10-24 x 1/2"
Carriage Bolts
Optional THDVDW1217
Hanging Equipment Mount
Optional THDVDW1217 Installation
Attach the THDVDW1217 to the TH100200W
75/100 VESA Plate or TH100200 Adapter Plate
with screws going through the adapter into
the back of the screen. The THDVDW1015 adapter
is trapped between the screen and the mounting plate.
Adding the THDVDW1217 may require longer
monitor attaching screws. 4mm, 5mm & 6mm
longer setscrews, hex nuts & washers
are provided with the THDVDW1217 mount.
Optional Height Adjustment
Optional Height Adjustment
The TH100200W 100/200mm Adapter Plate can be mounted
to the TH100200W 75/100mm Plate either above or below
the mount center line to allow for height adjustment
up or down up to 1-1/2".
Attach the TH100200W Adapter Plate with the desired
set of 100mm x 100mm square holes using the
#10-24 x 1/2" Carriage Bolts, Washers & Acorn Nuts.
Adjust the TH100200W Adapter Plate level with the
TH100200W 75/100mm Plate and tighten all four
Acorn Nuts
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
TH100200W INSTALLATION INSTRUCTIONS Page 3 of 3
©2013 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
TH100200W Wall Mount Installation
TH100200W_Ins (5/13)
with Optional THDVDW1015 - Hanging Equipment Mount

1/4"-20 Nylock Nut
Tilt Screw Installation
TH100200W Wall Arm
4Pl. 1/4" Belleville Washers
(Curved Side Facing Out)
2Pl. 1/4" Flat Washer
1/4"-20 x 2"
Hex Button Head Screw
VESA Plate Tilt Slot
Shown with 32" screen using a
200mm x 200mm mounting pattern
(Screen Not Included with Mount)
Screen Installation
TH100200W Mount
4Pl. 6mm x 12mm
or 8mm x 20mm
Phillips Screws
2Pl. 1/4" or 8mm
Flat Washers
TH100200W Short Arm
Pivot Screw
Optional Short Arm Installation
Tilt Screw Installation
Install the 1/4"-20 Hex Head Screw through the VESA Plate
Tilt Slot with the Washers and Nylock Nut oriented as shown
in the illustration.
Tighten both the pivot and tilt screws with enough torque
for the desired ilt angle and tilting tension. These screws
can be left loose enough to allow the screen to be tilted
after installation or tight enough to prevent the screen tilt
from being adjusted after installation.
Note: The curved 1/4" Belleville Washers should be installed
with the curved side facing out (away from the wall arm) to
facilitate smooth tilting action.
Screen Installation
(Check with the monitor manufacturer's documentation
to make sure that the provided 6mm x 12mm screws or
8mm x 20mm screws are suitable for installation. Longer
or shorter screws may be needed. Setscrews with washers
and nuts can also be used for screens with recessed
threaded inserts when needed. Contact Lucasey
Manufacturing if a different size and/or
length of monitor attachment screw is needed.)
Screw the top two Phillips screws into the back of the
screen leaving a 1/4" gap between the back of the screen
and the screw head.
Hang the screen onto the TH100200W VESA Plate with the
top top screws.
Attach the bottow two holes with Phillips Screws &
Washers.
Tighten the top two screws.
Optional Short Arm Installation
If installing the TH100200W Short Arm, remove the Pivot
Screw and replace the 6" projection wall arm with the
shorter 3-1/2" projection wall arm.
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
TH100200W INSTALLATION INSTRUCTIONS Page 2 of 3
©2013 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
TH100200W Wall Mount Installation
TH100200W_Ins (5/13)