Lucasey PCEC2410B User manual

3-1/2"
3/8"
1/8"
Top Plate
Socket Head Screws
(Provided with Monitor)
Glass Base
Bottom Plate
(10Pl.) Rivets
(6Pl.) Phillips Tapping Screws
PCEC2410B INSTALLATION INSTRUCTIONS
PCEC2410B_Install (8/08) ©2008 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
Page 1 of 2
1 ...
1 ...
2 ...
4 ...
6 ...
6 ...
Top Plate
Bottom Plate
Long Security Screws
Short Security Screws
Flat Washers
#10 x 1/2" Philips Screws
Component List
1.
2.
3.
4.
5.
Determine the appropriate location on the furniture
for the monitor. Mark the front edge of the monitor's
glass base on the countertop Mark a parallel line
1/8" back from the previous line.
Align the Bottom Plate with the second line and mark
each of the 6 screw hole locations.
Drill each of the marked screw locations with a 1/16"
drill bit 3/4" deep.
Attach the Bottom Plate with the provided Phillips Tapping
Screws
Attach the Top Plate to the Glass Base using three
Socket Head Screws from the bottom of the base.
for Philips Models: 37HFL5560, 42HFL5886 & 42HF7945
PCEC2410B - Bolt Down Furniture Mount

Holes for Steel Yoke
B
DETAIL B
(2Pl.) Washers
(2Pl.) 5mm x 25mm Security Screws
A
Steel Yoke
Glass Base
DETAIL A
(4Pl.) Washers
(4Pl.) Short Security Screws
Top Assembly
Bottom Plate
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
Page 2 of 2
PCEC2410B INSTALLATION INSTRUCTIONS
PCEC2410B_Install (8/08) ©2008 Lucasey Manufacturing Corporation, Oakland, California www.lucasey.com
Attach the Steel Yoke to the swivel on the Glass
Base using the Short Security Screws and Flat
Washers. See Detail A.
Be careful not to damage the Glass Base while
attaching the Steel Yoke.
Take the Top Assembly from Step 7 and align with
the rivets on the Bottom Plate. Slide the Top
Assembly forward until the Top and Bottom Plates
are locked together. Make sure all of the tabs on
the Top Assembly are engaged by pushing back and
forth to make sure Top Assembly is locked in place.
This step requires two workers.
Hold the Steel Yoke so that it does not move and
lower the monitor onto the arms as indicated in
the monitor user manual. The curved edge of the
Steel Yoke faces the front.
Secure the monitor to the Steel Yoke by screwing
the two Long Security Screws with Washers
into the holes indicated in Detail B.
6.
7.
8.
9.