Lucci CONNECT 299045 User manual

Installation Instructions
1 | P a g e V 1 . 0 ( 0 9 / 2 0 1 9 )
Lucci Connect Wall Switch
SKU#299045, 299046, 299047
Rated Voltage 220V - 240V~ 50Hz
Thank you for purchasing this quality Lucciproduct. To ensure correct function and safety, please read and follow all
instructions carefully before assembly, installation and use of this product. Please keep the instructions for future
reference.
Warranty
•This product is covered by 12 months warranty.The warranty is from date of purchase, not the date of installation.
•If this product is not assembled and installed by a licensed electrician the warranty will be void.
•Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
•Warranty will be void if there is any damage due to improper usage or modification to the product.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation Requirements
•The switch must be installed by a licensed electrician.
•All wiring and installation of this product must adhere to latest local and national wiring rules.
eg. AS/NZS 3000 Electrical installations in Australia.
•Check thepower rating of the light fittings which would be installed with this switch before commencing the
installation. The total powerof each circuit MUST NOT exceed rated circuit power (Max.300W) of the switch.
•This switch must NOT be used for a circuit with any motor speed control unit.
•Select a suitable location for installation:
−This product is suitable for indoor use only.
−Ensure this product is not installed in direct line of an air vent/system.
−If installing the product in an area prone to moisture, ensure that the area is well ventilated and an appropriately
rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as
such is not covered under warranty.
•Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
•If parts are missing, return the complete product to the place of purchase for inspection or replacement.
•Check whether the product has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
•Remove all packaging material from the product and be careful not to throw away accessories that may be hidden
within the packaging material.
Installation of the Receiver
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within
the packaging material.
NOTE:The switch includes 3 parts –Main body, Faceplate (Sold separately –SKU# 299055 One gang frost glass,
299056 two gang frost glass, 299057 three gang frost glass, 299065 one gang black glass, 299066 two gang black glass,
299067 three gang black glass), and Spacer for surface mounting box (Sold with the Faceplate). (Fig.1) Please select
and install according to your need.
WARNING: Switch OFF the electrical power of your circuit breaker on the switchboard before
commencing installation.

Installation Instructions
2 | P a g e V 1 . 0 ( 0 9 / 2 0 1 9 )
Installation to the wall mounting bracket:
1. Connect the power cables to the switch according to wiring diagram. (Fig.2)
NOTE:The earth terminal is not for protective earthing. It is optional and for termination purpose only.
2. Install the switch onto the appropriate wall mounting bracket by the 2 screws provided. (Fig.3)
3. Secure the faceplate (Sold separately) onto the switch. (Fig.3) Check and ensure the faceplate is covered firmly.
NOTE:Do not turn on the mains power until the faceplate is covered securely.
NOTE:Use a screw driver to remove the faceplate if it requires to be replaced. (Fig.4) Turn off the electrical power of
your circuit breaker on the switch board before attempting to replace the faceplate.
Installation to the surface mounting box:
If the switch is required to be install on the surface mounting box, the spacer will be required to be placed between the
mounting box and the switch. (Fig.5) Repeat the step 1 –3 to complete the installation.
Operation:
Turn on the mains power then set up the WIFI control according to the ‘Lucci CONNECT user guide’. The switch can also
be turnedon/off manually by touching the‘ ’ on the faceplate.

Installation Instructions
3 | P a g e V 1 . 0 ( 0 9 / 2 0 1 9 )
Safety Tips
•Exercise extreme caution when installing the switch, and always turn off electrical power at the main circuit breaker
before installing, removing the switch or replacing faceplate.
•Young children should be supervised to ensure that they do not play with the switch.
•Select a suitable location away from liquids and hazards.
•Do NOT soak or immerse the product in water or other liquids.
•Ensure that the product does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
SKU #
299045
299046
299047
Rated Voltage
220 - 240V~ 50Hz
Rated Load
300W Max.
600W Max. (2 x 300W Max. each
gang)
900W Max. (3 x 300W Max. each
gang)
Suitable Load
Incandescent / Halogen lamps, Fluorescent lamps, LED lamps, Motor
Weight
0.1kg / Set
Dimensions (With faceplate)
L:118mm W:72mm H:42mm E:9mm
Frequency
WIFI frequency: 2.4GHz