Lucent Technologies CIB 3130 User manual

CIB 3130
502B Headset Adapter
CIB 3130
Issue 1

CIB 3130
502B Headset Adapter
The 502B headset adapter allows you to use a headset with a 10-, 22-,
and 34-button voice terminal with your System 25 or MERLIN® II Com-
munications System. This headset adapter (Figure 1) comes with a
D8AC modular cord and may be used to connect a headset with a 2-
prong plug or a modular plug. This headset adapter provides the ability
to answer calls automatically without lifting the handset. For further
information, refer to “Operating the Headset Adapter.”
LED indicator
On/Quiet
button Off
button
Headset jack
(for 2-prong plug)
FIGURE 1 502B Headset Adapter
iss1, cib3130-1

Installing the Headset Adapter
Use the following instructions to install the headset adapter:
Place the headset adapter near the voice terminal to which it will be
connected.
If your headset has a 2-prong plug, insert it into the headset jack on
the front of the adapter (Figure 2).
1
2
LED indicator
On/Quiet
button Off
button
FIGURE 2 Connecting a Headset with a 2-Prong Plug
3If your headset has a modular plug, insert it onto the smaller jack on
the rear of the adapter (Figure 3).
iss1, cib3130-2

Off
button
On/Quiet
button
Terminal
jack LED indicator
Headset jack
(for a modular plug)
FIGURE 3 Connecting a Headset with a Modular Plug
4
5
Plug one end of the modular D8AC cord (provided with the adapter)
into the larger jack on the rear of the adapter (Figure 3).
Plug the other end of this modular cord into the jack labeled OTHER
on the bottom of the voice terminal (Figure 4).
iss1, cib3130-3

LINE
jack
10-Button voice
terminal
(bottom view) To station
jack
On/Quiet
button
OTHER
jack
Modular
(D8AC)
cord
Off
button
Headset (with a
2-prong plug)
FIGURE 4 Connecting Headset Adapter to Your Voice Terminal
OPERATING THE HEADSET ADAPTER
The 502B headset adapter allows you to answer calls automatically or
manually. Before you can use the automatic answering feature with your
headset adapter, you must program a button on your voice terminal for
Auto-Answer (Auto-Answer All for MERLIN II system users).
For programming instructions, refer to the administration information that
came with your system.
NOTE: If you disconnect your headset plug from the headset adapter
while a call is in progress, the call will be disconnected.
iss1, cib3130-4

Automatic Features
To: Do This:
Activate auto-answer
feature Press the programmed Auto-Answer button on your voice terminal.
The green light next to the button goes on.
Answer a call When you hear a beep and the Headset indica-
tor goes on, begin speaking.
Disconnect a call
Deactivate auto-answer
feature (manual opera-
tion)
To:
Place a call ●
●
●
Answer a call **
Disconnect a call
Calls automatically disconnect when the caller
(far-end) hangs up. This feature is available only
to System 25 users. MERLIN II system users
must manually disconnect calls by pressing OFF.
Press the programmed Auto-Answer button on
your voice terminal.
The green light next to the button goes off.
Manual Operation
Do This:
Press On/Quiet.
Listen for the intercom dial tone.
Dial number.
●Press On/Quiet.
●Press Off.
Other Features
To Switch From: Do This:
Handset to headset on Press On/Quiet.
an active call
●
●Hang up the handset.
Headset to handset on ●Lift handset.
an active call
** To answer calls manually, you must first deactivate the Auto-Answer feature.
iss1, cib3130-5