Ludlum Measurements 44-150-3 User manual

LUDLUM MODEL 44-150-3
GAMMA GM DETECTOR
May 2021

LUDLUM MODEL 44-150-3
GAMMA GM DETECTOR
May 2021
LUDLUMMEASUREMENTS,INC.
501 OAK STREET, P.O.BOX810
SWEETWATER, TEXAS 79556
325-235-5494,FAX:[phone]

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. May 2021
Model 44-150-3

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. May 2021
Table of Contents
Introduction 1
Unpacking and Repacking 2
Specifications 3
Operating Procedures 4
Safety Considerations 5
Parts List 6
Energy Response Curve 7
Drawing 8

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 1 May 2021
Introduction
The Model 44-150-3 is a high-sensitivity Geiger-Mueller (GM)
gamma survey detector that can be used with any portable ratemeter,
scaler instrument, or area monitor that provides 900 Vdc with an
input sensitivity of 30 +10 mV.
Note:
The detector does not contain any consumable materials.
Note:
If the detector is used in a manner not intended by the
manufacturer, the detector may not function properly.

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 2 May 2021
Unpacking and Repacking
Remove the calibration certificate or detector functional check
certificate and place it in a secure location. Remove the
detector(s) and accessories (if applicable) and ensure that all
items listed on the packing list are in the carton. If multiple
detectors are included, refer to the calibration certificates for
serial number (SN) matches. The Model 44-150-3 serial
number is located on the side of the detector.
To return an instrument or detector for repair or calibration,
provide sufficient packing material to prevent damage during
shipment and affix appropriate warning labels to promote
careful handling.
Every returned instrument must be accompanied by an
Instrument Return Form, which can be downloaded from
the Ludlum website at www.ludlums.com. Find the form by
clicking the “Support” tab and selecting “Repair and
Calibration” from the drop-down menu. Then choose the
appropriate Repair and Calibration division where you will find
a link to the form.

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 3 May 2021
Specifications
RECOMMENDED OPERATING VOLTAGE: 900 V
ENERGY RESPONSE (60 keV-1.3 MeV): within 30%
SENSITIVITY (137Cs Gamma): ≈ 13,500 cpm/mR/hr
BACKGROUND: ≈ 300 cpm
INPUT SENSITIVITY: 30 mV +10 mV
DEAD TIME: typically 50 microseconds
LINEARITY WITH DEAD TIME CORRECTION: 0.01 mR/hr to 80
mR/hr
LINEARITY WITHOUT DEAD TIME CORRECTION: 0.01 mR/hr to 8
mR/hr
TUBE: 30 mg/cm2stainless steel (Halogen quench) GM
TEMPERATURE RANGE: -15 to 50 °C (5 to 122 °F)
SIZE: 4.8 x 36.2 cm (1.9 x 14.3 in.) (Dia x L)
CONSTRUCTION: aluminum housing with beige powder-coat finish
WEIGHT: 0.9 kg (2 lb)
CONNECTOR: series “C”

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 4 May 2021
Operating Procedures
CONNECTING TO AN INSTRUMENT
Connect one end of the cable provided to the
detector by firmly pushing the connector
together while twisting clockwise ¼ turn until
latched. Repeat the process in the same
manner with the other end of the cable and the
instrument.
TESTING THE DETECTOR
1. Ensure that the instrument high voltage (HV) is at the
proper setting for the detector (900 volts).
2. Connect the detector to the instrument and check for a
proper background reading (≈ 300 cpm).
3. Expose the detector to a check source and verify that the
instrument indicates within 20% of the check source
reading from the last calibration. Alternatively, expose the
detector to a source of known value and verify that the
detector detects greater than or equal to the efficiency
listed in the specification section of this manual.
4. Instruments and detectors, which meet these criteria, are
ready for use. Failure to meet these criteria may indicate a
malfunction in the detector.

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 5 May 2021
Safety Considerations
ENVIRONMENTAL CONDITIONS FOR NORMAL USE
1. Indoor or outdoor use (in a dry environment)
2. No maximum altitude
3. Temperature range of -15 to 50 °C (5 to 122 °F); May be
certified for operation from -40 to 65 °C (-40 to 150
°F).
4. Maximum relative humidity of less than 95% (non-
condensing)
5. Pollution Degree 3 (Occurs when conductive pollution
or dry nonconductive pollution becomes conductive due
to condensation. This is typical of industrial or
construction sites.)
CLEANING INSTRUCTIONS AND PRECAUTIONS
The detector may be cleaned externally with a damp cloth,
using only water as the wetting agent. Do not immerse the
instrument in any liquid. Observe the following precautions
when cleaning:
1. Turn the instrument electronics OFF.
2. Allow the instrument to sit for one minute.
3. Disconnect the detector cable before cleaning the
detector.

Model 44-150-3 Gamma GM Detector
Ludlum Measurements, Inc. Page 6 May 2021
Parts List
Reference Description Part Number
UNIT Completely Assembled
Model 44-150-3 Gamma
Detector 47-4039
3 EA GM TUBE (LND 719/TGM) 01-5015
3 EA SOCKET-AMPH 78-S3S 01-5024
3 EA RES –3.3 MEG ¼ W, 5% CR 25 10-7044
1 EA 0 RING-2-029 16-8317
1 EA LUG-#14 N/L 1HL 1497 18-8766
1 EA Model 44-150-3 BODY ASSY 2002-1130
25 IN. WIRE-TEFLON WHT #22 HV 21-8993
24 IN. WIRE #22 BLACK UL1430 21-9413
11.7 IN. SHRINK-3/16 INCH BLACK 22-9504
1 EA CONNECTOR SERIES “C” 4478-011
8 EA Model 44-3, 44-2, 43-5 SPNG 7002-029-05
2 EA Model 44-150-3 TIN SLEEVE 7002-1127