LUMAHAWK LMM-PRO400 Manual

Introducon
Welcome to the world of LUMAHAWK LCD On-Camera Monitors.
The LMM-PRO400 is designed for composing and focusing images directly from your
DSLR or DV camera as well as viewing images and video clips from it. It’s simple
to use and accepts a variety of popular input formats. To take advantage of all the
features and to ensure safe operaon, please read through this instrucon manual.
Instrucons for Set-up of the
LMM-PRO400 On-Camera LCD Monitor
Front Panel Controls
The most frequently used monitor controls are directly accessed with the front panel
buons. These are:
V -Check Field Display
Push the ‘V’ buon to step through the RED, GREEN, BLUE and MONOCHROME check
elds.
Ʌ - Peak Focus Assist
Push the ‘Ʌ’ buon to toggle Peak Focus assist o and on.
> – Monitor Speaker Volume
Push the ‘>’ buon to increase speaker volume. While the Volume window is displayed,
you can also push ‘<’ to decrease speaker volume. Aer adjusng volume, push MENU
buon to hide the Volume window.
< – Screen Marker Display
Push the ‘<’ buon to adjust the viewnder perimeter indicator between 80%, 85%,
90%, 93%, 96% and O.
MENU
Display and hide OSD menu.
MODE
Select input sources HDMI or composite VIDEO. The source’s name will be displayed
briey when the buon is pushed.
CAMERA
Toggle the input source signal o and on.
Powering the LMM-PRO400
The LMM-PRO400 can be powered with either the supplied AC adaptor or with an F-style
DV baery such as the LUMAHAWK F-550 Li Ion Baery.
NOTE: Remove the baery from the monitor when not in use to ensure maximum baery
life.
Aaching the sun hood
Always close the sun hood before aaching it to or removing it from the monitor.
• To aach the sun hood to the monitor insert the two teeth towards the boom on
the hood’s frame into the two slots on the front of the monitor, just above the control
buons. With the teeth inserted all the way in, apply rm pressure on the top of the
hood’s frame and slide it down into the slot.
• To open the hood, li the top panel up followed by the le panel out and then the right
panel out (i.e starng with the top panel, open in a counter-clockwise order.)
• To close the hood, start with the right panel going in, then the le and nally the top (i.e
opposite order from opening)
• To remove the hood, rst close it. Then push the hood frame upwards towards the top of
the monitor and li away from the monitor face.
Turning Monitor on and selecng signal source
The power switch is located on the back of the monitor. Once the monitor is turned
on, the screen will turn blue and display the LUMAHAWK logo. The power indicator
LED on the front will also turn red.
Push the MODE buon to select the signal source. The LMM-PRO400 will display
signals from HDMI and composite video. When the monitor is receiving a signal from
the selected source, the image will appear on the screen and the power indicator LED
will turn green.
• Select HDMI to display a source connected to the monitor’s HDMI input.
• Select VIDEO to display a source connected to the monitor’s composite Video and
Audio inputs.
Cauon
• Only use the supplied power supply when not powering the monitor with a baery.
• Remove the baery when not using the monitor.
• Do not expose the monitor to extreme heat or humidity.
• Do not use harsh chemicals to clean the monitor. Gently wipe the screen with a clean
cloth to remove smudges and ngerprints.
• This monitor does not contain any user-serviceable parts inside. Do not aempt to
open the casing, as this will void your warranty. If service is required, please contact the
LUMAHAWK oces directly.
Troubleshoong
It’s normal for the screen to go dark for a few seconds when turning the camera or signal
source on or when toggling between dierent sources. It’s also normal for bright lines to
briey appear on the screen when the monitor is turned on.
Image displayed is black and white
• Check that the hue and saturaon levels are properly set.
• Set the Check Field to None.
• Ensure that cables running from the camera to the monitor are securely and properly
connected.
Image displayed is an abnormal or distorted color
• Check that the hue and saturaon levels are properly set.
• Set the Check Field to None.
• Ensure that cables running from the camera to the monitor are securely and properly
connected.
No image being displayed
• Check that both monitor and camera are turned on.
• Ensure that cables running from the camera to the monitor are securely and properly
connected.
• Check that the correct signal source is selected with the MODE buon.
• Check that power LED is green, indicang that the camera is sending a signal to the
monitor.
No Sound
• Check that volume on monitor is turned up.
• Ensure that cables running from the camera to the monitor are securely and properly
connected.
• Check that the correct signal source is selected with the MODE buon.
Included Accessories
• 5.6” LCD HD Camera Monitor
• F Style DV Baery Plate
• Shoe Mount Ball Head
• AC/DC Adapter
• Folding Sun Hood
• Mini HDMI to HDMI Cable
Front
1. Sun hood slot
2. Speaker
3. Screen marker display
4. Speaker volume
5. OSD MENU display
6. Check Field Display
7. Peak Focus Assist
8. MODE selecon
9. CAMERA power
10. Power LED
1
2
1
345678910
Side
18
19
Back
11
13
14
16
17
12
15
11. HDMI output
12. HDMI input
13. Composite video input
14. Analog audio input
15. Power switch
16. DC power input
17. Baery plate
18. Firmware port
19. Headphone jack

About Nadel Enterprises and Lumahawk
Nadel Enterprises and the Lumahawk brand are recognized worldwide as the leading
brand of high quality equipment for both professional and amateur photographers.
Using the most innovave photo-electronic technology coupled with simplicity of use,
Lumahawk products are specically designed for today’s digital studio and on-locaon
photography.
When it comes to capturing the image, Lumahawk exceeds the photographer’s demands
for reliability and versality.
Warranty
This product is warranted against poor workmanship and defecve materials for a
period of one (1) year from the date of purchase. This warranty does not include abuse,
careless handling, collateral damage and / or normal wear and tear. It is considered
normal for a minimal amount of pixels, to a maximum of three (3), to fail on the display
acve viewing area. Nadel Enterprises Inc. reserves the opon to refuse service for
display pixel failure if deemed unobtrusive to eecve use of the monitor by our
technicians.
It is Nadel Enterprises Inc.’s opon and discreon whether to repair or replace or reject
the warranty claim.
To apply for a warranty claim, return your product with proof of purchase to your dealer.
You can also contact us at 416.745.2622, 9 a.m. to 5 p.m. EST or via e-mail at
[email protected]om.
We reserve the right to change warranty terms without noce.
Using OSD to adjust monitor sengs
Push the MENU buon to show the OSD (On Screen Display).
This will then display the main OSD screen where you can access and make
adjustments to all the monitor’s features.
• To access a specic funcon, scroll through the four main secons (Color, OSD,
Funcon, Sound) using the ‘Ʌ’ and ‘V’ buons.
• When the desired funcon appears in the right column of the OSD, push the ‘>’
buon.
• Now use the ‘Ʌ’ and ‘V’ buons to scroll up or down unl the funcon is
highlighted in green. Refer to the following secons for individual funcon control
buons and opons.
• Aer making the adjustment, push the MENU buon to conrm the adjustment.
This will also return you to the OSD home screen where you can scroll through the
four main secons.
• To hide the OSD, push the MENU buon again.
Depending on the signal source, addional informaon about the image will be
displayed at the boom of the OSD window. In HDMI mode, the image resoluon is
indicated. In composite Video mode, the image standard (NTSC or PAL) is indicated.
LCD Panel TFT LCD 5.6” / 3072000 pixels
Resoluon 1280x800
Maximum resoluon 1920x1440
Brightness 350 cd/m²
Contrast rao 500:1
Viewing angle 85°/85 (L/R), 85°/85° (U/D)
Video signal input range 0.7~1.4Vp-p/75Ω
Supported input frequency H:30~60kHz V:60~75Hz
HDMI supported formats 480i, 480p, 576i, 576p, 720/ 50p /60p,
1080/ 50i/ 60i/ 50p/ 60p
Video color system NTSC-3.58 ; PAL-4.43
Backlight LED
Signal input channel HDMI / Composite Video
Input power voltage range DC6V-24V
Power consumpon ≤7 W
Standby current ≤50 mA
Working temperature -20~55°c
Storage temperature -30~65°c
Dimensions 163mm X 117mm X 44mm
Weight .3kg
Specicaons
www.lumahawk.com
Color
• Brightness
Adjust monitor image brightness
using ‘<’ and ‘>’ buons.
• Contrast
Adjust monitor image contrast using
‘<’ and ‘>’ buons.
• Hue
Adjust monitor image hue using ‘<’
and ‘>’ buons.
• Saturaon
Adjust monitor image saturaon using ‘<’ and ‘>’ buons.
• Check Field
Select Check Field to be displayed. Use ‘Ʌ’ and ‘V’ to select O, Red, Green, Blue or
Monochrome.
• Color Temp
Adjust the color temperature of the monitor image.
Use ‘Ʌ’ and ‘V’ to select 9300K, 7500K, 6500K or USER.
If USER color is selected, use ‘Ʌ’ and ‘V’ to scroll through R,G and B sengs and use
‘<’ and ‘>’ to increase or decrease specic values. Aer the desired color has been
set, push the MENU buon to return to the main Color Temperature list.
Funcon
• Reset
Return monitor to default factory
sengs using ‘<’ and ‘>’ buons.
• Display Rao
Toggle display rao between 16:9 and
4:3 using ‘<’ and ‘>’ buons.
• Screen Markers
Adjust Viewnder perimeter indicator
from 80%,85%,90%,93%,96% and O
using ‘Ʌ’ and ‘V’ buons.
• Centre Markers
Toggle cross hairs in the centre of the screen O and On using ‘<’ and ‘>’ buons.
• LR
Flip screen horizontally using ‘<’ and ‘>’ buons.
• UD
Flip screen vercally using ‘<’ and ‘>’ buons.
OSD
• Language
Select OSD language. Use ‘Ʌ’ and
‘V’ to choose from English, Chinese,
French, Italian, German, Spanish,
Japanese, Korean, Russian or
Portuguese.
• H Posion
Adjust the horizontal posion of the
OSD display using ‘<’ and ‘>’ buons.
• V Posion
Adjust the vercal posion of the OSD display using ‘<’ and ‘>’ buons.
• OSD Timeout
Adjust the length of me the OSD is displayed aer any buon is pushed using ‘<’
and ‘>’ buons.
• Camera
Toggle the signal from the camera o and on using ‘<’ and ‘>’ buons.
• Transparent
Adjust the background transparency of the OSD display using ‘<’ and ‘>’ buons.
HDMI Pass-through
The LMM-PRO400 features an HDMI output port that allows for HDMI pass-though. This
means that an addional HDMI monitor can be aached to the PRO400 via the HDMI
output port. This addional monitor will display the unmodied image (e.g. no centre
markers or check eld display) from the original HDMI source (i.e the source aached to
the PRO400 HDMI input)
Sound
• Volume
Adjust monitor speaker volume
using ‘<’ and ‘>’ buons.
• Focus
Toggle Focus indicator O and On
using ‘Ʌ’ and ‘V’ buons.
• Ver
Monitor’s rmware version.