Lumascape LS5030 User manual

LS5030 INSTALLATION INSTRUCTIONS
UNDERWATER LUMINAIRE
SURFACE MOUNT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
1 / 4
IN0191US N180207
READ ALL SAFETY INSTRUCTIONS FIRST
› Follow instructions carefully, failure to do so will void
warranty.
› Ensure installation complies with local law and
applicable standards.
› Input voltage is 30 V DC
› Only use Lumascape power supply, control equipment
and accessories.
› Ensure mains input power is surge protected.
› Never make connections whilst the power is
connected.
› Do not make modifications or alter the product.
› Luminaire is factory sealed; opening will void warranty.
LS5030
Fountain Light
WARNING
Install in accordance with
National Electric Code, ANSI/NFPA 70 or
the Canadian Electrical Code,
Part I (CEC), CSA C22.1

LS5030 INSTALLATION INSTRUCTIONS
UNDERWATER LUMINAIRE
SURFACE MOUNT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
2 / 4
IN0191US N180207
11.2” (285 mm)
2.7” (70 mm)
2.5” (63 mm)
100º
20º
Ø8.5” (217 mm)
Overview
Luminaire Assembly
Luminaire Mounting Foot
1.7” (44 mm)
3/8” (M10)
1/4” (M6)
30º
30º
Step 1 Screw the mounting foot to the luminaire body, Please note that the mounting foot can be reversed if required.

LS5030 INSTALLATION INSTRUCTIONS
UNDERWATER LUMINAIRE
SURFACE MOUNT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
3 / 4
IN0191US N180207
Step 2
Step 3 Step 4
Place the luminaire in the mounting position and mark the anchor points you wish to use.
Drill holes for mounting bracket as marked. Adjust luminaire rotation and secure
luminaire to mounting surface.
Mount Luminaire

LS5030 INSTALLATION INSTRUCTIONS
UNDERWATER LUMINAIRE
SURFACE MOUNT
LUMASCAPE ASIA PACIFIC Brisbane Technology Park, 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
LUMASCAPE NORTH AMERICA 1300 Industrial Road, Unit #19, San Carlos, CA 94070, USA
Phone [phone] | Fax [phone] | Email: [email protected] | www.lumacape.com
Products and specifications are subject to change without notice.
USA I Australia I Asia I Middle East I Europe
4 / 4
IN0191US N180207
Step 5
Step 6
Adjust luminaire tilt and tighten screw to lock in tilt.
Connect Luminaire to suitable 30 V DC power supply or low voltage PowerSync™master.
Ensure electrical connection is in accordance with local electrical code.
Power up the circuit to test the installation.
Tilt Adjustment
Tighten screw to lock
luminaire tilt into place.
Wiring Diagram
Wire Colour Designation
Black Power –
Red Power +
Orange* Data +
Grey* Data –
* Do not connect if not required
Data Signal Wires
Incorrect wiring will damage
luminaire and void warranty.
Do not Hi-Pot test. Isolate
these conductors if data
injector is not in use.
QUESTIONS Contact us at details below.