Lumena LUXROX 1 User manual

WARNINGS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE COMMENCING ANY WORK
•This is a Class 2 product –no earth required
•This unit must be fitted by a competent person –
if in doubt consult a qualified electrician.
•Install in accordance with IEE wiring regulations
and current Building Regulations.
•To prevent electrocution, switch off mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical
supply without your knowledge.
•This light fitting should be connected to a circuit with a 30Ma RCD fitted.
•When changing the bulb(s), always switch off at the mains & allow the bulb to cool
before handling –LAMP WILL GET HOT WHEN IN USE.
•All connections should be made as watertight as possible to avoid electrical shortage.
•Always use the correct type & wattage of bulb. Never exceed the wattage stated.
•The unit may get warm whilst on for a period of time.
•Cable must NOT be buried –locate on the surface or hook up on fence
•The plug supplied is not waterproof. Connect to a waterproof socket or inside
socket only.
Materials: Fibre Glass
Voltage: 220-240v
Max. Wattage: 20W
Lamp Fitting: E27
Recommended Lamp: LED
IP Rating: IP44
Product Size: Various
Cable: H05RN-F with 3 pin plug (may vary)
✔✔
2 YEAR
GUARANTEE
see website for
more details
Full Range & More Information Online: www.lumenalights.com
LUXROX Rock Light 240v (with plug)
INSTRUCTIONS
LUXROX 1 / LUXROX 2
LUXROX 3 / LUXROX 4

INSTALLATION:
•Approx. 3m length of 240v 3 core rubber cable is supplied with a 3 pin UK mains
plug fitted (H05RN-F –may vary).
•Simply plug the Rock Light into the outdoor waterproof mains socket.
•Install Bulb as per below.
•Mount the Rock Light in desired location with ground spike provided (see overleaf).
NOTES:
•Ensure all cabling is positioned carefully around the edges of the garden and clearly
visible, to avoid damage after installation. Do not bury the cable supplied with this
fitting.
BULB INSTALLATION:
•Turn off the power supply.
•Remove the base by unscrewing the 4 x screws.
•Screw the E27 / ES bulb into the bulb holder –DO NOT exceed maximum wattage
or overtighten.
•Ensure the cables have not become loose when removing the base.
•Replace the base and secure with the 4 x screws. Do not overtighten or this could
damage the outer shell. If there is damage around the predrilled holes, simply drill
new holes in a slightly different location to ensure the base is fitted securely.
Full LUXROX Range & More Information:
TIP:
As the LUXROX uses a standard E27
bulb, this enables more choice when it
comes to selecting the preferred type of
LED bulb; colour and brightness.

GROUND SPIKE INSTALLATION:
IMPORTANT
It is extremely important not to force the ground spike into harder ground as this
can result in broken or damaged lights and will invalidate the warranty. Please
follow the guidelines below
A four-fin anchor spike has been included for securing the
LUXROX into soft ground, measuring 150mm in length and
30mm in diameter.
Mounting into Earth: Soak the area with water until the
spike locations becomes wet mud, to a depth of 170mm.
Attach the spike to the threaded socket provided on the
LUXROX base and gently push into the wet mud. If there is
resistance, add a little more water to soften the earth. Once
dry, the ground spike will be secure.
Mounting into Grass: Remove a small area of turf. Follow the “Mounting into Earth”
instructions above.
Mounting into Gravel or Stones: Dig a hole 100mm in diameter and 170mm deep. Fill with
wet sand. Attach the spike to the threaded socket provided on the LUXROX base and gently
push into the wet sand. Push down on the top layer of sand to ensure it is tightly surrounding
the spike. Once the sand is dry, the light will be secure.
CLEANING:
Occasional cleaning and care is recommended for this product to avoid a build-up of grime
common in an outdoor environment. Simply wipe clean with a damp, soft cloth to remove
excess dirt. Do not scrub the exterior or use abrasive cleaners as this could damage the finish.
Please visit our website for more information on cleaning different materials.
www.lumenalights.com

FOUR DIFFERENT SIZES:
THREE DIFFERENT FINISHES:
RETURNS:
Returns will only be accepted with our prior agreement when a returns number will be issued.
Please contact us prior to returning goods, and include the relevant documents. Please see our
website for more information.
RETURNS, Lumena Lights Ltd, Centre 33 Long March, Daventry, Northants, NN11 4NR
Tel: [phone] Fax: [phone] Email: [email protected]
Producer Registration Number:
WEE/KC3440XY
www.lumenalights.com