Luminite OCULi HD LO15HD4GE User manual

OCULi HD
LO15HD4GE
Wireless HD 4G PIR Camera with a
15m x 90° Lens and 105° Field of View
2a Bellevue Road, Friern Barnet,
London N11 3ER
[e-mail]
020 8368 7887
Luminite Electronics Ltd.
www.luminite.co.uk
• Geng started
• oculi.online web portal
• iOS & Android app
V1

2 3www.luminite.co.ukwww.luminite.co.uk
Table of Contents Acvang your SIM
Acvang your SIM 3
How do our SIMs work? 4
SIM terms & condions 4
Creang an oculi.online account 5
Powering up the unit 6
Installing the speaker 8
Installing the solar panel 8
Events tab acons 9
Adding new units in the web portal 10
Adding new sites in the web portal 12
Adding new users in the web portal 14
Checking SIMs in the admin tab 15
Before you can use your OCULi unit, you will need an acve SIM card. To
acvate your SIM card, please contact Luminite to set up a direct debit
for your SIM.
We use BT UK SIMs that are non-network specic and will make use of
whichever network has the strongest signal, including the EE network.
The tari prices are inclusive of cloud server connecon charges.
To acvate your SIM card, please email [email protected] with the
following details:
Name:
Company:
Email address:
SIM Number:
Required Tari:
You will receive a Direct Debit mandate through GoCardless. Once the
mandate is lled in, you will be billed for your SIM tari monthly. For
queries regarding SIM taris and billing, email [email protected]
* * * OCULi will not work without an active SIM card * * *
Tari Descripon Cost per Month
50 Mb £6.50
100 Mb £10
250 Mb £12
512 Mb £15
1 GB £20

4 5www.luminite.co.ukwww.luminite.co.uk
How Do Our SIMs Work? Creang An oculi.online Account
OCULi Terms & Condions
Before you can use your OCULi unit, you will need an acve SIM card. To
acvate your SIM card, please contact Luminite to set up a direct debit
for your SIM.
We use BT UK SIMs that are non-network specic and will make use of
whichever network has the strongest signal, including the EE network.
SIMs on the same site do not pool their data or minutes.
There are a variety of taris as outlined on page 3.
Luminite reserves the right to cancel acvated SIMs at their discreon
with 1 week’s noce should the end user exceed their set data or voice
minutes allowance.
It is the responsibility of the end user to ensure that any computer, tablet
or smart phone is data compable and that data is turned on in order to
connect to the cloud server and view footage.
It is the responsibility of the end user to ensure that the OCULi unit is
sited in an area with good 3G / 4G cellular signal.
Direct Debit details must be provided to Luminite* before the SIM is
assigned to the end user. (*see Acvang Your Unit, page 3)
Visit www.luminite.co.uk/oculi to view the full Terms & Condions.
By using OCULi, you agree to the Terms & Condions by default.
To use the web portal to control and monitor your OCULi units, you
need to create an account on oculi.online.
Go to www.oculi.online and click Register in the top right corner.
Fill in the following elds, making sure to use your correct company
name as this is how the account will be idened.
• Company Name
• First Name
• Last Name
• Phone Number
• Email
• Conrm Email
• Password
• Conrm Password
Once you have registered your oculi.online, your acvated SIMs can
be assigned to your account. To have your SIMs assigned, please email
[email protected] or call us on 020 8368 7887 with your SIM card
number.
Once the SIMs are assigned to the portal, they can be ed into the
OCULi unit along with the baeries.

6 7www.luminite.co.ukwww.luminite.co.uk
Powering Up The Unit
If using rechargeable baeries and a solar panel, t them in series as shown
below using the solar adaptor kit:
If using SAFT lithium D cells, t them in series as shown below:
*Please note that rechargeable baeries will not work without the baery adaptor
Powering Up The Unit
Undo the unit using the allen key provided and remove the back cover.
Insert your acvated and assigned SIM card into the slot as indicated on
the diagram on page 7. OCULi can either use 2 x non-rechargeable SAFT
lithium D cells OR 2 x rechargeable baeries with a solar panel.
• LED 4 will illuminate 15-30 seconds aer start-up to indicate that the
unit is iniang a connecon to the server
• LED 6 will illuminate shortly aer to show that the modem has started
correctly
• LED 5 will ash whilst the modem searches for a network, and will
stay lit aer the connecon has been established
Once the connecon to the server is established, the OCULi unit will take
a series of images and upload them to the server as an Inialisaon event,
which will be viewable in the web portal.

8 9www.luminite.co.ukwww.luminite.co.uk
Events Tab AconsInstalling The Speaker
Installing The Solar Panel
To mark an event as ‘read’ and stop it from ashing in the list of events,
click on the dropdown arrow next to ‘Clear event, enter an oponal log
message’ above the event footage and select ‘Mark as read’.
Stop and start the event footage by pressing Start Video and Stop Video.
Change the brightness and contrast of the video by moving the sliders
underneath the event footage.
Save the event as sll frame images by clicking Save as Images, or save
the event as a video clip by clicking Save as Video.
View individual frames by clicking them on the scrollbar at the boom
of the screen.
Remove the grey screwcap from the boom of the units back cover and
insert the cable gland. Push the wires through the cable gland and screw
them into the 5-way terminal block as shown in the diagram on page 7.
Tighten the gland around the cables.
If using alongside the Solar Panel make sure each cable is ed through
a separate gland to ensure a snug, waterproof t.
Fit the speaker securely. If the speaker falls it may cause damage to the
OCULi processor board.
Remove the grey screwcap from the boom of
the units back cover and insert the cable gland.
Push the wires through the cable gland and
screw them into the 2-way terminal block as
shown in the diagram on page 7. Tighten the
gland around the cables.
If using alongside the Speaker, make sure each
cable is ed through a separate gland to ensure
a snug, waterproof t.
Ensure that the solar panel is sited in an area
with good south facing light that isn’t shady otherwise you may have
low power issues with the rechargeable baeries.
Fit the solar panel securely using an appropriate bracket, which is
available separately if required. If the solar panel falls it may cause
damage to the OCULi processor board.
Event Types
Red Detecon
Green Tamper
Orange External
Purple Cloak On
Olive Cloak O
Maroon Move
White Day
Black Night
Yellow Inialisaon
Blue Heartbeat

10 11www.luminite.co.ukwww.luminite.co.uk
Adding New Units In The Web Portal
Once a unit has made a successful connecon to the server, it will
self-populate in the Units tab. Once the unit has been created, you can
change the name, which site it is assigned to, power saving sengs and
PIR sensivity.
The Heartbeat frequency of the unit determines how oen it will make a
connecon to the server to update its sengs and status. Any changes
that you make to arming schedules or unit sengs will not be updated
on the device unl it has made its next Heartbeat connecon.
If the unit is using a Solar Kit, then ‘Stay Online’ mode may be acvated.
In Stay Online mode, the modem remains acve in low power and can
listen for changes made in the server. This means that any sengs or
arming schedule changes can be made quickly without waing for the
next Heartbeat and is important to note when inially seng up a unit.
Always remember to hit Save at the boom of the page aer making
changes to your site.
My unit has had an initialisation event but won’t detect anything
If your unit won’t detect anything aer it’s inial connecon, you need
to check both the units’ individual arming schedule, and the arming
schedule of the site it’s assigned to. If the unit or site is set so that the
unit is disarmed at the me of installaon, change the arming schedule
to allow the unit to be armed. Next, change the Heartbeat so that it is
set to ‘Every hour’. This will enable the unit to check in with the server
every 10 minutes to update its sengs.
Once the unit has updated its sengs, you will be able to test the
detecons. Leaving the unit armed more oen or seng the Heartbeat
to happen more frequently will aect the baery life and use data, so
remember to change the sengs back once you have tested the unit.
Adding New Units In The Web Portal
My unit hasn’t had an initialisation event but the SIM has made a
connection in the Admin tab
Open the OCULi unit and press the pink reset buon to restart the
board. Once the modem makes a connecon to the server, you should
see the inialisaon event appear in the Events tab.
Sll no event? The unit may not have a good cellular connecon. Try
changing the locaon of the OCULi unit and pressing the pink reset
buon again.
My unit hasn’t had an initialisation event and the SIM hasn’t made
a connection in the Admin tab
Is your SIM card acve? Your OCULi unit cannot make a connecon if
the SIM card hasn’t been acvated. Contact us to discuss acvang your
SIM card.
Has your SIM card been linked to your account? In the Admin tab, check
your list of SIM numbers to see whether your SIM number appears in
the list. If the SIM number doesn’t show up, speak to us to link your SIM
number to your oculi.online account.
If your SIM has been linked to your account but hasn’t made a
connecon yet, you should check your baery level. You should only
use the recommended SAFT lithium D cell baeries in your OCULi as
other brands may be unstable. Are your baeries ed correctly? Check
to make sure that the baeries are ed in series as shown on the
diagram on page 6. If you’re using rechargeable baeries, make sure that
they’re ed correctly as shown in the diagram on page 6 and that your
connected solar panel is geng a good amount of light.

12 13www.luminite.co.ukwww.luminite.co.uk
Adding New Sites In The Web Portal
Once a unit has made a successful connecon to the server, a default
site will be created in the Sites tab. This default site is designed to be
used as a template for creang other sites. Change the sengs in the
default site and then scroll to the boom of the page to save the default
site as another site.
If you want the site to have a master arming schedule that overpowers
the arming schedule of individual units, make sure that ‘Site has Master
Schedule’ is cked underneath the ‘Overrides individual units’ secon.
Enable your site to update with release rmware, not beta rmware.
If you want to integrate with a CMS plaorm such as IMMIX, select the
plaorm from the drop-down menu in the Plaorm Integraon secon
and click the green Integraon box. In the pop-up window, ll in the
required elds (click the blue Info box to show which values need to be
entered in which box) and then hit Save.
To assign a new user to a site, select their name from the list of Users
underneath ‘Assign A User To Site’ and then click on ‘Add role to
site’. One a user is added, you can click on Sengs to choose which
nocaons they will receive to the web portal, their email address and/
or the mobile phone app.
Always remember to hit Save at the boom of the page aer making
changes to your site.
Adding New Sites In The Web Portal
The Save Site button isn’t working
Refresh the web portal by hing F5 on your keyboard, and if that
doesn’t x the issue, log out of your oculi.online account and log back in
again. If the Save Site buon sll doesn’t work, clear the cookies cache
in your web browser, refresh the page and try it again.
I’m not getting any notifications from my site
Make sure that you assign yourself to the site in order to receive
nocaons. Click on your user details in the ‘Assign Site to Users’ box
and click ‘Add Role To Site’.
Have you enabled nocaons in the sengs window? Once you’re
added a user on a site, click the yellow ‘Sengs’ box and make sure that
the relevant nocaons that you want to receive are cked. Make sure
that you click Save Site aer any changes.

14 15www.luminite.co.ukwww.luminite.co.uk
Adding New Users In The Web Portal
When you make your oculi.online account, the rst user created will
be made with the details you used to sign up and will be assigned the
Manager role by default. To add a new user, go into the Users tab and
hit the ‘Add New User’ buon underneath User Management.
New users can have separate logins for the same registered account
and can be assigned dierent roles. Admin and Manager roles have full
control over units and sites within the portal, whereas Operators can
only view events and receive nocaons.
I can’t create a new user
Go to another oculi.online tab such as the Events tab, then go back to
the Users tab and click on the Add New User buon without clicking
anything else. You can also try refreshing the web portal by hing F5
on your keyboard, and if that doesn’t x the issue, log out of your oculi.
online account and log back in again.
The new user login options are populated with my user details
Go to another oculi.online tab such as the Events tab, then go back to
the Users tab and click on the Add New User buon without clicking
anything else. You can also try refreshing the web portal by hing F5
on your keyboard, and if that doesn’t x the issue, log out of your oculi.
online account and log back in again.
Checking SIMs In The Admin Tab
You can see which SIMs have been assigned to your account underneath
‘Available SIMs’.
SIMs that have made a connecon will be visible underneath ‘SIMs and
Units with valid SIMs’. You will be able to see the unit’s name and last
connecon to the server.
Underneath ‘Pending SIM list’, you are able to request SIM acvaon
by typing your SIM number into the box and clicking on ‘Request SIM
acvaon’. Please not that this will only request the SIM to be assigned
to your oculi.online account and will not acvate the SIMs data plan. In
order to acvate a SIM, you must contact Luminite at support@luminite.
co.uk. Pending SIMs will show underneath this.
I can’t see any SIMs underneath ‘Available SIMs’
Have you requested that your SIM is assigned to your portal? Either
follow the step above to assign your SIM, or contact support@luminite.
co.uk with your details.

2a Bellevue Road, Friern Barnet,
London N11 3ER
[e-mail]
020 8368 7887
Luminite Electronics Ltd.
www.luminite.co.uk