lumishore LUX DL50 User manual

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
1
LUX Downlight DL50 Installation Guide
Full spectrum color tuneable lighting, including cold and warm white light
Please read the following pages before attempting installation
Before you start…
• Always ensure that the vessel’s power source and battery are disconnected or isolated prior
to installation.
• A qualied professional should carry out both the electrical and mechanical installation.
• The Lux Downlight Is designed to be used in conjunction with the Lumishore Lux
Downlight module (see diagram below). Do not connect to any other 3rd party lighting
control products or dimmers.
• The lux downlight is fully sealed and can be installed inside or outside, it can be installed in
wet areas but is not designed to be permanently submerged in water.
• Choose a location – the light must be mounted on a at – not curved surface.
• The rear of the light may get warm to touch, it will not cause damage to the mounting
surface.
45-0146-Rev1
LUX Downlight Control Module Installation Guide

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
2
Basic Dimensions:
HOLE CUT-OUT
NOTE: The Lumishore Lux downlight DL50 requires connection to the Lumishore Lux Downlight
Module. For full electrical installation and wiring diagrams please refer to the Lux Downlight
Module installation guide.
Power rating = 4.5watts per light
Typical current draw = 0.37A @ 12Volt / 0.18A @24Volt
Installation Diagram
(1.11in)
28.30mm
(1.93in)
49mm
(0.079in)
2mm (2.520in)
ø 64mm
(2.00in)
ø 50.80mm

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
3
Mechanical Installation:
Using a hole saw cut a 2in hole, always cut the hole smaller than needed and le to the correct size to
ensure a snug t. For indoor installations use the supplied spring clips, gently pull back the spring clips
and feed the light into the hole, releasing the spring clips as the light is positioned.
For exterior installations or wet areas it is recommended that the light is xed in place using a suitable
marine sealant / adhesive. Remove the spring clips from the xture and dispense a small amount of
adhesive around the glass bezel. Push into place using a slight rotation of the light to spread the adhe-
sive evenly. Clean any excess adhesive using a soft cloth and soap and water – DO NOT USE CHEMICAL
CLEANERS.
Warranty
LUMISHORE Ltd warrants the LUX Downlight DL50 to be free from defects in workmanship and materials
for a period of two years, starting from the date of original purchase. Misuse, abuse, improper installation,
neglect, improper shipping, damage caused by disasters such as re, ood, and lightning, installation by
unqualied personnel, unauthorized repair or modication will void this warranty. For the avoidance of
confusion and doubt, non-compliance with all installation, maintenance and operating instructions in this
document constitute non-conformance with warranty terms.
The LUX Downlight Control Module is designed to work with Lumishore LUX strip lighting products
ONLY, do not use with other Strip light brands, this will invalidate the warranty.
MARINE SEALANT