Lutron Electronics MAESTRO MS-OPS2 User manual

Custom Settings for Maestro®Occupancy Sensing Switches
Application Note #461
Revision B
August 2012
1 Technical Support — 800.523.9466
Model Numbers
MS-OPS2 MS-VPS2
MS-OPS5M MS-VPS5M
MS-OPS6M2-DV MS-VPS6M2-DV
MS-OPS6M2N-DV MS-VPS6M2N-DV
Overview
Maestro®Occupancy sensing switches have custom settings that can be adjusted to the user’s preference. The
settings include Timeout, Sensor Mode, and Advanced Settings (see the Custom Settings section for descriptions of
these settings).
General Instructions
Setting options vary depending on model number. Use the model number to identify which options are available and
then follow the instructions under each Custom Settings table.
Read all instructions before proceeding.
1. Press and hold the button(s) indicated in the picture below.
2. The lens will flash once at each setting; it will always start at setting 1.
3. The setting will be saved after releasing the button(s).
On/Off Button
Auxiliary Button
Lens

Application Note #461
2 www.lutron.com
Custom Settings
Select your preferred settings from the instructions on the following pages before proceeding; default settings are
shown in bold.
Note: User is required to remove the wallplate in order to gain access to the Auxiliary button.
Timeout
• Timeout is the delay until light turns off after a room is vacated.
• Test Mode is a temporary, short timeout (less than 15-seconds) that can be used to test the sensor’s coverage. After
entering test mode, the device will exit test mode automatically after 5 minutes, or when any button is pressed. If no
motion is detected for more than 15 seconds, the light will turn off. If motion is detected, the light will turn on and
continue to stay on for as long as motion is detected. The lens will flash periodically, indicating that motion has been
detected.
Model Numbers
MS-OPS2 MS-VPS2
MS-OPS5M MS-VPS5M
Number
of flashes
1Test mode
21 minute
35 minutes
415 minutes
530 minutes
Example 1a: Changing the Timeout to 15 minutes
1. Press and hold the On/Off button.
2. Release the button after the lens flashes for the fourth
time.
Model Numbers
MS-OPS6M2-DV MS-VPS6M2-DV
MS-OPS6M2N-DV MS-VPS6M2N-DV
Number
of flashes
1Test mode
21 minute
35 minutes
415 minutes
530 minutes
Example 1b: Changing the Timeout to 30 minutes
1. Press and hold the On/Off button.
2. Release the button after the lens flashes for the fifth
time.

Application Note #461
3 Technical Support — 800.523.9466
Sensor Mode
• Auto-On Daylight Sensing is the mode in which the light turns on only if natural light in the room is low. If the switch
turns on when there is enough natural light, or if the switch does not turn on when there is not enough natural light,
press the On/Off button within 5 seconds of entering the room. Over time, this interaction will “teach” the switch your
preferred setting.
• Manual Off-While-Occupied is a feature that can be enabled or disabled to accommodate different lighting scenarios.
– Enabled: When the occupancy sensing switch is manually turned off, the light will turn off and remain off while the
room is occupied (e.g., during the viewing of a presentation in a conference room or classroom).
– Disabled: When the occupancy sensing switch is manually turned off, the light will turn off. After 25 seconds have
elapsed, the light will turn on and remain on for as long as the occupancy sensor detects motion in the room.
Manual Off-While-Occupied Actions
Sequence of Events Enabled Disabled
Room is occupied Light is ON Light is ON
Occupancy sensing switch is manually turned off Light turns OFF Light turns OFF
Room remains occupied Light remains OFF Light turns ON after 25seconds
Room is vacated Light remains OFF Light remains OFF
Timeout period expires Light remains OFF Light turns OFF
Room becomes occupied Light turns ON Light turns ON
Model Numbers
MS-OPS6M2-DV
MS-OPS6M2N-DV
Number
of flashes
1Auto-On and Auto-Off (Occupancy mode);
Off-while-occupied ENABLED
2Manual-On and Auto-Off (Vacancy mode)
3Auto-On daylight sensing and Auto-Off;
Off-while-occupied ENABLED
4Auto-On and Auto-Off (Occupancy mode);
Off-while-occupied DISABLED
Model Numbers
MS-OPS2
MS-OPS5M
Number
of flashes
1Auto-On and Auto-Off (Occupancy mode);
Off-while-occupied DISABLED
2Manual-On and Auto-Off (Vacancy mode)
3Auto-On daylight sensing and Auto-Off;
Off-while-occupied ENABLED
4Auto-On and Auto-Off (Occupancy mode);
Off-while-occupied ENABLED
Example 2: Changing the Sensor Mode to Auto-On Daylight Sensing and Manual Off-While-Occupied enabled.
1. Press and hold the Auxiliary button.
2. Release the button after the lens flashes for the third time.

Application Note #461
4
Advanced Settings
Model Numbers
MS-OPS2 MS-VPS2
MS-OPS5M MS-VPS5M
MS-OPS6M2-DV MS-VPS6M2-DV
MS-OPS6M2N-DV MS-VPS6M2N-DV
Number
of flashes
1Motion sensitivity low
2Motion sensitivity high
3Return all settings to default
Example 3: Changing to Low Sensitivity
1. Press and hold On/Off and Auxiliary buttons simultaneously.
2. Release both buttons after the lens flashes for the first time.
Lutron Contact Numbers
Maestro is a registered trademark of Lutron Electronics Co., Inc.
WORLD HEADQUARTERS
USA
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
TEL: [phone]
FAX: [phone]
Toll-Free: 1.888.LUTRON1
Technical Support: 1.800.523.9466
[email protected]
North & South America
Technical Hotlines
USA, Canada, Caribbean:
1.800.523.9466
Mexico:
+1.888.235.2910
Central/South America:
+1.610.282.6701
EUROPEAN HEADQUARTERS
United Kingdom
Lutron EA Ltd.
6 Sovereign Close
London, E1W 3JF United Kingdom
TEL: [phone]
FAX: [phone]
FREEPHONE (UK): 0800.282.107
Technical Support: +44.
(0)20.7680.4481
[email protected]
ASIAN HEADQUARTERS
Singapore
Lutron GL Ltd.
15 Hoe Chiang Road
#07-03, Tower 15
Singapore 089316
TEL: [phone]
FAX: [phone]
Technical Support: 800.120.4491
[e-mail]
Asia Technical Hotlines
Northern China: 10.800.712.1536
Southern China: 10.800.120.1536
Hong Kong: 800.901.849
Indonesia: 001.803.011.3994
Japan: +81.3.5575.8411
Macau: 0800.401
Taiwan: 00.801.137.737
Thailand: 001.800.120.665853
Other Countries: +65.6220.4666
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 U.S.A.
P/N 048461 Rev. A8/2012