LuxHome LHR100SU User manual

LuxHome
433MHz Wire Free Remote Control
Installation and Operating Instructions
These instructions should be read in conjunction with
your System Installation and Operating Instructions
and be retained for future reference.
Introduction
The LuxHome Remote Control is designed for use
with LuxHome Wire Free Intruder Alarm systems
operating on 433MHz only.
Tr ansmit LED
Any number of Remote Controls can be used with your
system, providing they are all coded with the same
system House Code.
The Remote Control is powered by a CR2032 type
Lithium Cell battery which under normal conditions will
have a typical life up to 1 year. Under normal battery
conditions the LED on the Remote Control will only
illuminate when a button is pressed. However, under
low battery conditions the LED will flash every time
the button is pressed. When this occurs the battery
should be replaced as soon as possible.
Arm
Part-Arm/
Delay-Arm*
Disarm
Slide up
to operate
Personal Attack
Setting the Remote Control
The Remote Control has no Tamper Protection
1. Remove the front cover by undoing the small screw on
the rear of the Remote Control.
* Part Arm with Control Unit
Systems or Delay-Arm with
Siren only systems
The Remote Control Unit is used to Arm and Disarm
the
system. The Remote will activate the Instant Arm, Part-
Arm/Delay-Arm or Disarm functions dependent upon which
System it will be used with (refer to your System
Installation and Operating Manual).
The Remote Control also incorporates a Personal Attack
Switch (PAS). Activating the PAS will immediately initiate a Full
Alarm condition whether the system is Armed or Disarmed,
(unless the system is in Service, Test or Program mode).
House Code
Dip Switches
Jumper Link
Battery Clip
Battery
2. Located above the battery cover is a row of 8 DIP
switches. These switches set the House Code for the

Remote Control and must be set to the same ON/OFF
combination as the House Code DIP switches in all
other System Devices.
3. The Jumper Link is used to enable/disable the Personal
Attack Switch (PAS) dependent on which type of Alarm
System is in use.
If used with a Siren-controlled Alarm System (i.e. a
system without a separate Control Panel), the jumper
link located immediately below the House Code DIP
switches must be removed for the PAS to work.
If your System has a separate Control Panel then this
link must be fitted in place for the PAS to work.
4. Remove the battery from its packaging and insert it under
the clip, ensuring that the + terminal faces upwards away
from the PCB.
5. Replace the rear cover and fixing screw.
Testing the Remote Control
System in normal operating mode
The operation of the Remote Control should be tested with
the system in normal operating mode to ensure that the
new Remote Control will successfully communicate with the
system and the Arm and Disarm functions operate
correctly. Also check by activating the PAS on the Remote
to initiate an alarm condition.
Refer to your System Installation and Operating Manual for
further details on operating and testing the system.
Disposal and Recycling
Disposal of this product is covered by the
Waste Electrical or Electronic Equipment
(WEEE) Directive.
It should not be disposed of with other
household or commercial waste.
At the end of its useful life the packaging and product should
be disposed of via a suitable recycling centre. Please
contact your local authority or the retailer from where the
product was purchased for information on available facilities.
Guarantee
The product is guaranteed for one year from the date of
purchase against faulty materials and workmanship. No liability
can be accepted for any problems caused by fair wear and
tear, buyer’s negligence, improper fitting or use, wilful or
accidental damage, or any consequential loss or damage
howsoever caused. This guarantee does not affect your statutory
rightsandisvalid forUK and EIREonly.
If you believe the product to be faulty or in the unlikely event of
the product developing a fault during the warranty period, then
please contact yoursupplierfor product assistance. Product repair or
replacement will be offered for faulty products only with our prior
agreement. Should you need to return a product then:
1. Contact your supplier and obtain a Return Authorisation
Number.
2. Adequately package your product to prevent damage in transit
and include the following:
a. A copy of your original invoice/receipt.
b. A covering letter giving your full contact details, including
email address (if applicable).
c. A description of the fault or problem.
LuxHome Alarm Systems
Manufactured by Everspring
Copyright 2013. All Rights Reserved.
Everspring Industry Co., Ltd.
3F., No. 50, Sec 1, Zhonghua Rd., Tucheng Dist.,
New Taipei City 23666, Taiwan
TEL: [phone] FAX: [phone]
Website: www.everspring.com
Service Support: [e-mail]