Luxium ZR30 User manual

Product/Service Information
Luxium Lighting
Bring out your Colors!
Luxium Lighting
7624SE 7th Ave.
Portland, OR 97202
Phone: [phone]
E-mail: [email protected]
ZR30
Adaptable-Color
DMX Lamp
WARNING: The ZR30 is powered by a
switching power supply and is not intend-
ed to be dimmed by a line-voltage dim-
mer. Socket should be wired directly to
the power-line mains.
Accidental connection of RJ45 jacks to
non-DMX512 equipment (e.g., an Ether-
net Hub at a patch bay) may result in
damage to equipment.
RJ45 jacks for
DMX in/out
DIP Switch for DMX addressing
and built-in functions Attachment of
optional diffusers
Edison screw base
for AC power
Installation
The LuxiumTM ZR30 is a self-contained
PAR-30 size LED lighting solution capa-
ble of DMX512 or stand-alone operation.
It has a wide input power supply, so will
operate on any voltage that your likely to
find on an E26/E27 “medium screw
base” lamp socket.
The ZR30 has five operating modes that
are selected via an 8-position DIP switch
on the side of the lamp.
The ZR30 may be connected to a
DMX512 controller via the RJ45 jack,
also on the side of the lamp. Multiple
ZR30s may be daisy-chained onto a sin-
gle DMX512 cable.
If installed in a fixture please leave at
least ½ inch (12mm) of clear space sur-
rounding the ZR30 housing to facilitate
air flow.
Voltage: 90VAC … 250VAC, 50/60Hz
Power: 25W (at maximum output)
Environmental: 5C … 45C, 10-90%RH
non-condensing.
Control Input: DMX512-A on RJ45 con-
nector as described in ANSI E1.11-2008
Optional Diffuser Kit
The LuxiumTM DK1 Optical Diffuser Kit is
a set of 5 different filters that are used to
adjust the beam angle of the ZR30.
This is an excellent option for creating a
smooth and uniform beam with the ZR30
lamp. These filters are easy to install on
the front of the lamp and are held in place
by the bezel ring.
Useful for situations that require a more
diffuse beam that spreads out over a wid-
er angle than the standard narrow beam
spot light.
Beam spread can be adjusted from 30
degrees to 60 degrees depending on
the chosen insert.
Install diffuser film under tabs around
lamp bezel. Use slight pressure to gen-
tly bend diffuser film and snap into
place.
Copyright - Luxium Lighting 2016Specifications subject to change without notice

Operating modes, sequences and DMX ad-
dress for the ZR30 are set via an 8-position DIP
switch on the side of the lamp.
Selectable-White Mode
Switches: 1000 cccc
Lamp displays calibrated white CCTs
Ballyhoo Mode
Switches: 1011 0bbb
In this mode, the ZR30 will run one of 8 pre-
defined color sequences.
Color-Mixer Mode
Switches: 1010 uuuu
Each internal LED string assigned to a DMX
channel so each color adjusted individually
without using internal blending algorithms.
DMX address is computed as: Address=
((unit x 6) + 1)
Selectable-Color Mode
Switches: 1001 cccc
Lamp displays a single color at full intensity.
DIP Switch Setting
0000 six-color, medium speed
0001 six-color, slow speed
0010 seven-color
0011 salsa
0100 traffic
0101 x-mas
0110 winter wonderland
0111 sunset
0000 No output
0001 Red
0010 Green
0011 Yellow
0100 Blue
0101 Magenta
0110 Cyan
0111 Blended White RGBY - 6500K
1000 B.A. Bastard Amber
1001 Special Lavender
1010 Steel Blue
1011 Violet
1100 Blue-Green
1101 Orange
1110 Tungsten
1111 All White, RGBW - 4000K
MODE SWITCHES SETTINGS
Blended-Color, 4-ch DMX512 0uuu uuuu uuu uuuu = binary unit number (0…127)
Color-Mixer, 6-ch DMX512 1010 uuuu uuuu = zero-based unit number (1...15)
Selectable-White, Static CCTs 1000 cccc cccc = CCT selector (0…15) from table
Selectable-Color, Static RGBW 1001 cccc cccc = Color selector (0...15) from table
Ballyhoo Mode 1011 0bbb bbb = Ballyhoo pattern selector (0...7)
Orientation
Hold the ZR30 lamp with the lens up and the
screw base down, the switch will be correctly
oriented. A switch shown with the value of ‘1’
is a switch that is in the up position (toward the
lens) and a switch that is shown with a value of
‘0’ is a switch that is in the down position.
Connecting DMX512
The ZR30 includes RJ-45 connectors to inter-
face with a DMX console and other DMX
lamps. A CAT5 cable or XLR is used for con-
trol. A wireless ZR30-AX1 receives DMX from
a Wi-DMX transmitter. When pairing or switch-
ing to wired only mode the ZR30 must first be
reset to factory conditions. See wireless trans-
mitter instructions for details. DO NOT CON-
NECT ETHERNET OR PEO TO RJ-45 INPUT
OR THE LAMP WILL BE DAMAGED!
Blended-Color Mode
Switches: 0uuu uuuu
A ZR30 occupies 4 slots on the DMX512 net-
work. In this mode the ZR30 receives four
DMX512 channels, assigned to Red, Green,
Blue, and White, in that order. Output colors
are expertly blended based on the color re-
quest implied by the DMX512 input levels.
uuu uuuu = Zero-based binary unit number.
The address for the ZR30 is computed as:
DMX512 Address = ((unit x 4) + 1). For exam-
ple: 0000 0001 = DMX 5, 0000 0010 = DMX 9.
‘1’ = on
‘0’ = off
See operation guide for full list of DMX settings
0000 No output 1000 4000K
0001 2400K 1001 4500K
0010 2700K 1010 5000K
0011 2850K 1011 5600K
0100 3000K 1100 6500K
0101 3250K 1101 Half RED
0110 3500K 1110 Half BLUE
0111 3850K 1111 Max White
Used to set DMX and modes