Lyfco Allarp 166-1-63 User manual

ASSEMBLY MANUAL
BRUKSANVISNING
Model name: Allarp
Modellnamn: Allarp
SKU: 166-1-63
Konsumentkontakt
Arc E-commerce AB
Box 3124
13603 Haninge
XX-YYWW
Please don’t remove the batch code sticker at back side of this product!
Any feedback please take picture of this batch code for traceablity purpose
NOTE: 50% TIGHTEN BEFORE FIXING ALL BOLTS
VIKTIGT – LÄS MONTERINGSANVISNINGARNA NOGA INNAN DU BÖRJAR
Ta inte bort ettiketten med batchnummer som finns på möbeln. Om du behöver hjälp med service eller reklamation av din möbel –
ange möblensbatchnummer till återförsäljaren, så att du kan få rätt reservdelar till just din möbel.

Attention! Please note that at rst all screws should be inserted slightly by hand!
Turn 2-3 times so that the screw grips on its own and connects all elements loosely. The screws
must only be driven in tightly when all elements are connected with each other in this way.
Otherwise the setup won´t be possible. Only by driving them in tightly afterwards, small
deviations of the borehole or the welded joints, which always occur with handcrafted products,
can be compensated.
Notes on an optimized assembly:
Before you completely tighten the screws, check carefully all the screws and tighten them
(only) to the extent that the product remains (especially chairs or loungers) still under load. If
you are sure that your product can withstand load, place it on a solid, level ground and put
some weight on it, please carefully and always with cushions. The various components can then
align with each other. Then tighten completely the screws. Thus you achieve and optimal
alignment of the product and prevent wobbling. Don’t sit, nd some weight.
Your new product was made by hand.
Slightly irregularities are rather seen as a
quality attribute than as a reason for
complaints.
Tip: Always fully insert the hex key inside
designated notch of screw.
If you don´t do that and slip out of the
screw, the screw will suffer damage and it
can caused the screw head to become
round inside you won´t be able to nd grip
with the hex key anymore!
VIKTIGHT
Don´t use this product if parts are missing, damaged or
worn down.
Don´t use any electronic tools to set up these product.
The high energy of these electronic tools will cause
screw overg ten and therefor they won’t grid.
Don´t overg ten screwws or bolts. Only ten the
screws enely aaer the product is completely set up.
You shouldn’t sit or stand on it.
Don´t let your product stand in the rain. Protect it from
weather impacts. In mes of feeze and over the
winter, we suggest you to store the product in a
covered dry place.
Var uppmärksam! Sätt först i samtliga skruvar löst. Dra inte åt, för då nns risk att skruvhålen inte
passar.
Innan du drar åt skruvarna helt, gör såhär för bästa resultat:
Ställ möbeln på en helt slät yta och lägg ett tillräckligt tungt föremål (ca 10-15kg) på den, så att
alla ben nuddar marken. Skruva därefter i skruvarna helt. Obs – använd inte din kroppstyngd, då
det är för mycket vikt. Om du följer dessa råd, blir din möbel stabil.
Om du inte följer dessa instruktioner kommer möbeln att bli ostadig och ”vickig” då produkten
upplevs ojämn.
Din nya möbel är handgjord. Små avvikelser
kan därför förekomma och är ett
kvalitetsattribut snarare än ett fel.
Tips: Var noga att alltid sätta in insexnyckeln
helt ner i skuven.
Om du inte gör det nns risk att insexnyckeln
slinter, vilket skadar skruven.
Skruvenkandåbliobrukbar.
Använd inte den här produkten om delar saknas,
är skadade eller utslitna.
Använd inte elektriska skruvdragare för att
montera produkten. Den höga kraften i elektriska
verktyg kommer dra åt skruvarna för hårt vilket
kan skada gängorna.
Spänn inte skruvar eller muttrar för hårt. Dra åt
alla skruvar efter att hela möbeln monterats.
Stå eller sitt inte på bordet.
För att förlänga livslängden på möbeln, undvik
att låta den stå i regn. Under vintertid
rekommenderar vi att möbeln förvaras inomhus,
i torr miljö.
DONT’S

Component
A
B
C
D
E
F
Right Seat Frame
Right Front Frame
Side Frame
1 pc
1 pcs
1 pc
1 pc
1 pc
1 pc
Right Frame
Bottom Frame
Right Back Frame
Hardware
1
2
3
4
5
6
Bolt M6x40mm
Bolt M6x25mm
14 pcs
54 pcs
40 pcs
Washer M8x10 mm
Sofa Leg
1 pc
4 pcs
18 pcs
Bolt M6x30mm
Washer M8x2 mm

Component
G
H
I
K
Left Seat Frame
Left Front Frame
1 pc
1 pc
1 pc
1 pc
Left Frame
Left Back Frame
Hardware
8
9
7
L
Side Frame 1 pc
Box Cover Frame Table Glass
M
10
11
12
Rain cover
Sofa Leg 2 pcs
Seat Cushion 4 pcs
Back Cushion 4 pcs
Fabric 1 pc
1 pc
1 pc
1 pc

Component
N
O
Q
1 pc
1 pc
1 pc
1 pc
1 pc
Allen key
Box Bottom Frame
Box Left Frame
Box Right Frame
Box Front Frame
Box Behind Frame
Table Big Side Frame
P
R
S
1 pc
2 pcs
T
U
Table Small Side Frame
Table Top 1 pc
2 pcs
V
Inner Frame 1 pc
13
Component

STEP 1
Connect Right frame (A) & Right back frame (B) with Bolt (1)
B
A
1
1
1
1
1
1
1
1C
STEP 2
Connect part from STEP 1 & Right seat frame (C) with Bolt (1)

D
2
2
2
E
STEP 3
Connect part from STEP 2 & Front frame (E)
STEP 4
Connect part from STEP 3 & Side frame (D) with Bolt (2)

11
STEP 5
Connect part from STEP 4 & Rain cover (11). Tie the ropes to the round holes
F
1
1
1
1
1
1
STEP 6
Connect part from STEP 5 & Bottom frame (F) with Bolt (1)
11

STEP 7
Connect part from STEP 6 & Sofa leg (6), (7) with Bolt (3)
3
3
3
3
7
6
8
9
STEP 8
Put on Seat cushion (8) & Back Cushion (9) to complete right bench

STEP 9
Connect Left Back Frame (H) & Left Seat Frame (I) with Bolt (2)
2
2
2
2
I
H
STEP 10
Connect part from STEP 9 & Left Frame (G) with Bolt (2)
2
2
2
G
G
H

STEP 11
Connect part from STEP 10 & Side Frame (L) with Bolt (2)
L
2
2
K
2
2
2
2
22
STEP 12
Connect part from STEP 11 & Left Front Frame (K) with Bolt (2)

STEP 13
Connect part from STEP 12 & Inner Frame (V) with Bolt (2)
V
2
2
STEP 14
Connect part from STEP 13 & Sofa Leg (6) with Bolt (3)
3
3
6

STEP 15
Put on Seat Cushion (8) & Back Cushion (9) to complete left bench
P
Q
2
2
STEP 16
Connect Box Right Frame (P) & Box Front Frame (Q) with Bolt (2)
9
8

N
2
2
2
STEP 17
Connect part from STEP 16 & Box Bottom Frame (N) with Bolt (2)
O
STEP 18
Connect part from STEP 17 & Box Left Frame (O) with Bolt (2)
2
2
2

R
2
STEP 19
Connect part from STEP 18 & Box Behind Frame (R) with Bolt (2)
2
2
2
2
3
36
STEP 20
Connect part from STEP 19 & Sofa Leg (6) with Bolt (3)

2
4
2
M
2
STEP 21
Connect part from STEP 20 & Box Cover Frame (M) with Bolt (2) & Washer M8 (4)
STEP 22
Connect part from STEP 21, Gaslift & Washer M8 (5) with Bolt (2)
25

STEP 23
Connect part from STEP 22 & Fabric (10) to complete cushion box.
10
STEP 24
Connect Table Big Side Frame (S), Table Small Side Frame (T) & Table Top (U) with Bolt (2)
2
2
2
2
S
T
U

STEP 25
Connect part from STEP 24, Table Big Side Frame (S) & Table Small Side Frame (T)
with Bolt (2)
2
1
2
2
2
T
S
STEP 26
Connect part from STEP 25 & Sofa Leg (6) with Bolt (3)
3
36

STEP 27
Put on Table Glass (12) to complete table
12