
Attention! Please note that at first all screws should be inserted slightly by hand!
Turn 2-3 times so that the screw grips on its own and connects all elements loosely. The screws
must only be driven in tightly when all elements are connected with each other in this way.
Otherwise the setup won´t be possible. Only by driving them in tightly afterwards, small
deviations of the borehole or the welded joints, which always occur with handcrafted products,
can be compensated.
Notes on an optimized assembly:
Before you completely tighten the screws, check carefully all the screws and tighten them
(only) to the extent that the product remains (especially chairs or loungers) still under load. If
you are sure that your product can withstand load, place it on a solid, level ground and put
some weight on it, please carefully and always with cushions. The various components can then
align with each other. Then tighten completely the screws. Thus you achieve and optimal
alignment of the product and prevent wobbling. Don’t sit, find some weight.
Your new product was made by hand.
Slightly irregularities are rather seen as a
quality attribute than as a reason for
complaints.
Tip: Always fully insert the hex key inside
designated notch of screw.
If you don´t do that and slip out of the
screw, the screw will suffer damage and it
can caused the screw head to become
round inside you won´t be able to find grip
with the hex key anymore!
VIKTIGHT
Don´t use this product if parts are missing, damaged or
worn down.
Don´t use any electronic tools to set up these product.
The high energy of these electronic tools will cause
screw overtighten and therefor they won’t grid.
Don´t overtighten screws or bolts. Only tighten the
screws entirely after the product is completely set up.
You shouldn’t sit or stand on it.
Don´t let your product stand in the rain. Protect it from
weather impacts. In times of freeze and over the
winter, we suggest you to store the product in a
covered dry place.
Var uppmärksam! Sätt först i samtliga skruvar löst. Dra inte åt, för då finns risk att skruvhålen inte
passar.
Innan du drar åt skruvarna helt, gör såhär för bästa resultat:
Ställ möbeln på en helt slät yta och lägg ett tillräckligt tungt föremål (ca 10-15kg) på den, så att
alla ben nuddar marken. Skruva därefter i skruvarna helt. Obs – använd inte din kroppstyngd, då
det är för mycket vikt. Om du följer dessa råd, blir din möbel stabil.
Om du inte följer dessa instruktioner kommer möbeln att bli ostadig och ”vickig” då produkten
upplevs ojämn.
Din nya möbel är handgjord. Små avvikelser
kan därför förekomma och är ett
kvalitetsattribut snarare än ett fel.
Tips: Var noga att alltid sätta in insexnyckeln
helt ner i skuven.
Om du inte gör det finns risk att insexnyckeln
slinter, vilket skadar skruven.
Skruvenkandåbliobrukbar.
Använd inte den här produkten om delar saknas,
är skadade eller utslitna.
Använd inte elektriska skruvdragare för att
montera produkten. Den höga kraften i elektriska
verktyg kommer dra åt skruvarna för hårt vilket
kan skada gängorna.
Spänn inte skruvar eller muttrar för hårt. Dra åt
alla skruvar efter att hela möbeln monterats.
Stå eller sitt inte på bordet.
För att förlänga livslängden på möbeln, undvik
att låta den stå i regn. Under vintertid
rekommenderar vi att möbeln förvaras inomhus,
i torr miljö.
DONT’S