LYNKSYS LM500 User manual

LYNKSYS TECHNOLOGIES CO., LTD.

Note
Before using the product, please read the Quick Guide to
fully benefit from it.
This product involves constant upgrading and/or
improvement, our company reserves the right to change the
specifications of software and/or hardware mentioned in this
operating guide without any prior notice. The product
specifications and information mentioned in the operating
guide are for reference only.
Check list
Please check the following accessories before you discard
the packing material. Please contact your local dealer
immediately if there is any missing or damage parts.
Accessories
Quantity
LM500
1
Power cable
1
Bracket
1
Quick Start Guide
1
Antenna
1
Palm Mic
1

1. Overview of LM500
LED indicator light
Operating state Indication
Standby Green(Blinking)
Searching Network Green(Fast Blinking)
Power On Green(Blinking)
PTT Transmitting Green(Steady)
PTT Receiving Green(Steady)
Offline Red(Steady)

2. Installation of SIM card
1. Uncover the SIM slot at the back of the LM500
2. Insert the SIM card as shown in the picture
3. Insert the SD card into the slot as show in the picture
4. Cover the slot
SIM Card Slot SD Card Slot

3. Power the LM500
Connect the power cable to the rear of the LM500
Risk of electric shock
Dry location use only DC output of 16 volts
Power Wire

WARNING: MAKE SURE YOUR LM500 IS POWERED
OFF WHEN IT'S NOT IN USE.
Important:
Use only the approved wire.
Do not connect to the wrong wire.
4. Basic operations
Start up
Long press the power button until the LM500 starts up.
Shut Down
Long press the power button, select the “power off” when the
option shows on screen to shut down the UE.
Button/Antenna Interaction
●P1: Substitute PTT button when your Palm Microphone is not
able to properly used.
●P2: Return key - press and return to the last menu
●P3: Home key - press and return to home screen directly
●P4: Menu key - press and show the current pages.
●Antenna: Make sure the antenna will not affect the vision of
your driving and set it up properly.
WiFi Connection
Go to the Settings > WiFi interface. Enable the WIFI option
(single click to revert the status), switch to find the right access
point you want to connect to, single click the right access
point then input the password in (Single click to input
uppercase, double click to input lowercase). Switch to select

inputting characters. Click “√” to confirm / exit the password
inputting.
GPS Location
Go to the Settings > Location interface, single click to enable or
disable GPS location.
Date & Time Configuration
Go to the Settings > Date&Time interface, single click to
configure time display format.
Bluetooth Connection
Go to the Settings > Bluetooth interface, Switch to choose “PTT
Button”, single click to enable Bluetooth connection, after
Scanning for a while, switch and find the right device name,
single click to confirm bonding to the Bluetooth button, others
Bluetooth device please choose “Headset” with the same
operation.
Cellular Data Connection
Go to the Settings > Cellular data interface, single click to revert
enable or disable cellular data connection.
Language
Go to the Settings > Language interface, switch and single click
to choose the right language.
Factory Reset
Go to the Settings > Reset interface, under the interface “Are
you sure about recovery?”, switch the options, choose “Yes” to
reset and “No” to exit.

System Information
Go to the Settings > About interface, find the device and SIM
card information including Operation System Version, IMEI
Code, Battery Percent, SIM Name, SIM Level, SIM Type.
System Update
Go to Settings > System Update interface, single click to check
updates.

5. Basic Installation
This section descrips how to install LM500 in the vehicle
Overview
Below is the overview of the LM500 with buttons and ports
Figure 5-1
Figure 5-2

5. Basic Installation
This section descrips how to install LM500 in the vehicle
Procedure
1. Install the bracket to the vehicle. See Figure 5-3
2. Secure the LM500 to the U-shape bracket. See Figure 5-4
3. Connect the RSM to the LM500. See Figure 5-5
4. Connect the power cable. See Figure 5-6
Figure 5-3 Intalling the Bracket Figure 5-4 Secure LM500 to the U-shape bracket
Figure 5-5 Connect the RSM to LM500 Figure 5-6 Connect the power cable to LM500