Lynx P MX 3214 B User manual

Series 3000
© LYNX Technik AG
Brunnenweg 3
64331 Weiterstadt
Germany
www.lynx-technik.com
Reference Manual
P MX 3214 B; P MX 3214 D
Dual AES Audio Multiplexer
MiniModule
s
V 3.1

Reference Manual P MX 3214 Version 3.1
Page 2
Information in this document is subject to change without
notice. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or
mechanical for any purpose, without express written permission
of LYNX Technik AG.
LYNX Technik AG may have patents, patent applications,
trademarks, copyrights or other intellectual property rights
covering the subject matter in this document. Except as
expressly written by LYNX Technik AG, the furnishing of this
document does not give you any license to patents,
trademarks, copyrights or other intellectual property of LYNX
Technik AG or any of its affiliates.
© LYNX Technik AG 2006 all rights reserved

Reference Manual P MX 3214 Version3.1
Page 3
Warranty
LYNX Technik AG warrants that the product will be free from
defects in materials and workmanship for a period of two (2)
years from the date of shipment. If this product proves defective
during the warranty period, LYNX Technik AG at its option will
either repair the defective product without charge for parts and
labor, or will provide a replacement in exchange for the
defective product.
In order to obtain service under this warranty, customer must
notify LYNX Technik of the defect before expiration of the
warranty period and make suitable arrangements for the
performance of service. Customer shall be responsible for
packaging and shipping the defective product to the service
center designated by LYNX Technik, with shipping charges
prepaid. LYNX Technik shall pay for the return of the product to
the customer if the shipment is within the country which the LYNX
Technik service center is located. Customer shall be responsible
for payment of all shipping charges, duties, taxes and any other
charges for products returned to any other locations.
This warranty shall not apply to any defect, failure, or damage
caused by improper use or improper or inadequate
maintenance and care. LYNX Technik shall not be obligated to
furnish service under this warranty a) to repair damage resulting
from attempts by personnel other than LYNX Technik
representatives to install, repair or service the product; b) to
repair damage resulting from improper use or connection to
incompatible equipment; c) to repair any damage or
malfunction caused by the use of non LYNX Technik supplies; or
d) to service a product which has been modified or integrated
with other products when the effect of such modification or
integration increases the time or difficulty servicing the product.
THIS WARRANTY IS GIVEN BY LYNX TECHNIK WITH RESPECT TO THIS
PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED. LYNX TECHNIK AND ITS VENDORS DISCLAIM ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. LYNX TECHNIK`S RESPONISIBILITY TO REPAIR AND
REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE
REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS
WARRANTY. LYNX TECHNIK AND ITS VENDORS WILL NOT BE LIABLE
FOR ANY INDIRECT, SPECIAL, INCIDENTIAL, OR CONSEQUENTIAL
DAMAGES IRRESPECTIVE OF WHETHER LYNX TECHNIK OR THE
VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH
DAMAGES.

Reference Manual P MX 3214 Version 3.1
Page 4
Regulatory information
Europe
Declaration of Conformity
USA
FCC 47 Part 15
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to the part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own
expense
We LYNX Technik AG
Brunnenweg 3
D-64331 Weiterstadt
Germany
Declare under our sole responsibility that the product
TYPE: P MX 3214 -2 B, P MX 3214 -2 D
To which this declaration relates is in conformity with the following
standards (environments E1-E3):
EN 55103-1 /1996
EN 55103-2 /1996
EN 60950 /2001
Following the provisions of 89/336/EEC and 73/23/EEC directives.
Winfried Deckelmann
Weiterstadt, November 2006
Place and date of issue Legal Signature

Reference Manual P MX 3214 Version3.1
Page 5
Contents
Warranty ...................................................................................3
Regulatory information............................................................4
Europe ......................................................................................4
Declaration of Conformity ...........................................................4
USA............................................................................................4
FCC 47 Part 15 ............................................................................4
Contents ...................................................................................5
Getting Started.........................................................................7
Packaging ...............................................................................7
Product Description ...............................................................7
Functional Diagram ...............................................................9
Module Layout........................................................................9
Connections...........................................................................11
Video Connections ..............................................................11
Balanced Audio Connections (P MX 3212 D)..................11
Power Connections..............................................................12
DC Power Connector .................................................................12
Installation ..............................................................................13
Mechanical ...........................................................................13
Stand Alone Operation...............................................................13
Multiple Units ............................................................................14
Electrical Installation. ...........................................................15
Stand Alone Operation...............................................................15
Multiple Units ............................................................................16
Settings and Control ..............................................................16
Switch Settings ......................................................................17
Service Adapter..........................................................................17
Switch Function Detail ..............................................................18
Auto Store..................................................................................19
Factory Preset Condition............................................................20
Alarm/LED Status Indicators.................................................. 21
LED Indicators...........................................................................21
Front Panel Alarm Indicator ......................................................22
Locate Function .........................................................................23
Specifications (P MX 3212) ...................................................24
Available Options..................................................................25
Parts List ..................................................................................26
Contact Information ..............................................................28

Reference Manual P MX 3214 Version 3.1
Page 6
This Page is intentionally left blank

Reference Manual P MX 3214 Version3.1
Page 7
Getting Started
Packaging
The shipping carton and packaging materials
provide protection for the module during transit.
Please retain the shipping cartons in case
subsequent shipping of the product becomes
necessary.
Product Description
The P MX 3214 is a high quality digital AES Audio
multiplexer (Audio Embedder) designed primarily
for broadcast and professional applications.
The Module accepts 4 external AES3 inputs
(combined into two audio groups) and multiplexes
this into the incoming SDI video input. Group
insertion per embedder is selectable (1 through 4).
Four separate SDI outputs of the video, with
embedded audio are provided. Existing audio
groups can be overwritten, deleted or passed
transparently. Four separate SDI outputs of the
embedded signal is provided which could be used
to cascade several modules for additional audio
group insertion.
In case no SDI input is attached the module
generates it own SDI signals and continues to
embed the AES input signals.
The Module uses Sub D connections (P MX 3214 D)
or 75 Ohm BNC connections (P MX 3214 B) for
audio and standard 75-Ohm (BNC)
interconnections for video.
The P MX 3214 has a variety of features, which include:
•User selectable audio groups (1…4)
•525 and 625 line standard. (auto detect)

Reference Manual P MX 3214 Version 3.1
Page 8
•Supports 4:3 / 16:9 aspect ratios
•Supports 8 and 10 bit video
•Selectable bypass of audio sample rate
conversion
•Video to green if SDI input lost, with own SDI
signal generated
•Supports asynchronous and synchronous
audio inputs. (Asynchronous audio between
30KHz and 48KHz)
•local DIP switches and LED's for control and
status monitoring.
•Microprocessor controlled.
•Remote control interface.
All settings stored in non-volatile flash ram.
The module has a built in micro-controller with local
controls, status and alarm indicators and well as
internal flash ram for storing setups. Any operational
parameters configured and stored into the module
are recalled when powered up. Remote control,
status monitoring and error reporting is possible
when used with the R FR 3010 rack frame option
and host controller. For stand alone control, the
R CT 3002 Service Adapter option is available.
The P MX 3214 is part of the 3000 series of
MiniModules, which offer high quality, modularity
and flexibility in a very small form factor ideal for
applications where space is at a premium.
The modules can be used either stand alone using
the optional power supply brick, or as part of a
tightly integrated space saving system where up to
10 MiniModules can be mounted utilizing the
optional LYNX R FR 3005 / 3010 rack housing. This
includes integrated power supply and optional
remote control interfaces.

Reference Manual P MX 3214 Version3.1
Page 9
Functional Diagram
Figure 1 below is the basic functional diagram for
the P MX 3214 MiniModule.
Figure 1- P MX 3214 Functional Diagram
Module Layout
Figure 2 shows the physical layout of the P MX 3214
MiniModule. Video I/O is made through standard
75 Ohm BNC video connections and the balanced
audio inputs are made on the Sub D connector (P
MX 3214 D) or the unbalanced audio inputs on BNC
connectors (P MX 3214 B). Module configuration is
set via a small dip-switches located behind access
holes in the bottom of the module.
If the module is being used in a stand alone
application then the optional power supply (R PS
3001 E, R PS 3001 U or R PS 3001-3) is required to
power the module (not shown)

Reference Manual P MX 3214 Version 3.1
Page 10
Figure 2 – Module Layout

Reference Manual P MX 3214 Version3.1
Page 11
Connections
Video Connections
The P MX 3214 MiniModule is configured with
standard 75 Ohm BNC connectors for video I/O
Connection is self-explanatory. Balanced audio
connections are made via the Sub D connector
and should be wired as shown in the table below.
We recommend the use of high quality cable
suitable for digital video / audio connections to
reduce the risk of interference or errors due to
excessive cable attenuation.
Note. Due to the compact design of the module it
will be necessary to use a connection tool to
secure the BNC video connectors to the module.
Balanced Audio Connections (P MX 3214 D)
SubD 25 pin female connector.
Pin
Number Connection Pin Number Connection
1 14
2 15
3 16
4 17
5 18
6 19
7 + AES 4 20 - AES 4
8 GND AES 4 21 + AES 3
9 - AES 3 22 GND AES 3
10 + AES 2 23 - AES 2
11 GND AES 2 24 + AES 1
12 - AES 1 25 GND AES 1
13
113
1425

Reference Manual P MX 3214 Version 3.1
Page 12
!
Power Connections
If using the module in a stand-alone application
use the separate R PS 3001 E (for Europe), R PS 3001
U (USA) power brick option or the R PS 3001-3 IEC
desk power supply.
DC Power Connector
The MiniModule has a captive power lead fitted to
the module, with a male 5 pin locking bayonet
connector. This connection provides DC power
and also data connectivity to the module.
Connector wiring is shown below.
3
4
51
2
GND
+ 5V
i2C-SDA (data)
i2C-SCL (clock)
Power ConnectionData Connection
Male Connector
(view looking into connector from front)
Caution
Only use the optional LYNX R PS power
modules. Ensure the 5-pin power
connector is locked securely in place.

Reference Manual P MX 3214 Version3.1
Page 13
!
Installation
Mechanical
Stand Alone Operation
The P MX 3214 MiniModule can be used in a stand
alone application. There are two options for the use
of the module in this way.
a) Using the R FR 3005 Rack Frame 1 option. This
allows up to any 10 of the MiniModules to be
secured onto a rack frame assembly for 19 inch
rack mounting. This keeps the modules secured,
organized and out of the way. The R PS 1 power
brick option or the R FR 3010 option is required
to power each module. Please refer to the R FR
3005 Reference Manual supplied with this
option for more details.
b) Single Use. The MiniModule can be powered
independently with the R PS 3001 option and
used in any location where this functionality is
required.
Caution. Care needs to be taken
when using the module in this way, as
it is not physically secured. Keep the
module away from the floor to avoid
the risk of someone stepping or
tripping on the unit, and locate the
unit away from excessive sources of
heat and any sources or moisture.
If using more than one MiniModule in any
installation, the R FR 3005/3010 Rack frame
combination is highly recommended.

Reference Manual P MX 3214 Version 3.1
Page 14
Multiple Units
Most applications will require more than one
MiniModule, which can include any of the
available Series 3000 MiniModule product range.
There are two options for mounting multiple units.
a) Using the R FR 3005 Rack Frame option. This
allows up to any 10 of the MiniModules to be
secured onto a rack frame assembly for 19 inch
rack mounting. The R PS 3001 power brick
option or the R FR 3010 option is required to
power each module. Please refer to the R FR
3005 Reference Manual for more details.
b) Using the R FR 3010 Rack frame extension
option. Can be combined with the R FR 3005
Rack frame option. Each module plugs into a
connection bus, which provides common
power for all modules. (no R PS external power
supplies are needed). Remote control and
status monitoring of all modules is possible with
the addition of the R CT 5020 rack controller
and R CT 5030 master controller options. Please
refer to the respective reference manuals for
these options for details of mechanical
installation.
The very small size and density of the MiniModules
combined with the available rack frame options
allows the addition of a complex and custom signal
distribution system without taking any additional
front rack space. The rack frames are designed for
installation in the back of 19-inch racks where there
is normally plenty of available space. Ideal for
mobile truck installations and facility expansions
where space is at a premium.

Reference Manual P MX 3214 Version3.1
Page 15
!
!
Electrical Installation.
Stand Alone Operation
The MiniModule requires the R PS 3001 power brick
option for stand-alone operation. Two versions are
available R PS 3001 E for European markets, R PS
3001 U for the US markets or the R PS 3001-3 IEC
desk power supply. Please ensure you have the
correct power option for your region. The
connection to the module is made with a small 5-
pin connector, which has a twist bayonet securing
system. Please make sure the connection is solid
and locked in place. A strain relief is included within
the module to prevent excessive strain on the
connection.
Signal connections should be made with care,
please ensure connections are correct and
compatible equipment is feeding / receiving the
signals from the module or damage can result.
Caution. Only use the optional LYNX R PS 1
power modules. Ensure the 5-pin power
connector is locked securely in place.
Caution. Care needs to be taken when
using the module in this way, if it is not
physically secured. Keep the module
away from the floor to avoid the risk of
someone stepping or tripping on the unit,
and locate the unit away from excessive
sources of heat and any sources or
moisture.

Reference Manual P MX 3214 Version 3.1
Page 16
Multiple Units
When installing multiple MiniModule units it is
recommended you use the R FR 3005 Rack Frame 1
and / or R FR 3010 Rack Frame 2 options. Please
refer to the documentation supplied with these
options for details on electrical installation.
Settings and Control
The P MX 3214 is configured via an integrated 8-
position dip switch as shown below. (Figure 3)
Figure 3. Switch and LED locations

Reference Manual P MX 3214 Version3.1
Page 17
Switch Settings
Below the switch setting for the two 8-position dip-
switches is defined. Please see the section following
the table for more detail on each switch function.
ONE DIP SWITCH IS PROVIDED FOR EACH EMBEDDER
Service Adapter
This module is complex by design. Configurations
are much easier with the R CT 3002 Service
Adapter. This provides a simple PC GUI for
configuration use. Settings can be quickly changed
and stored to the module flash ram. No local switch
settings are necessary. A single Service Adapter
can be used for all MiniModules.
SWITCH
Position Set Function
ON Local Adjustment Enabled
1 OFF Local Adjustment Disabled
ON 24 bit AES output
2 OFF 20 bit AES output
ON Delete ALL incoming embedded AES audio
3 OFF ONLY replace Audio group selected with SW2
ON No sample rate conversion performed
4 OFF Sample rate conversion selected (48KHz)
ON Group 1 selected
5 OFF Group has to be deselected if other group
selected
ON Group 2 selected
6 OFF Group has to be deselected if other group
selected
ON Group 3 selected
7 OFF Group has to be deselected if other group
selected
ON Group 4 selected
8 OFF Group has to be deselected if other group
selected

Reference Manual P MX 3214 Version 3.1
Page 18
Switch Function Detail
All settings are stored in Flash Ram inside the
module (see Auto Store section in this manual).
Settings will be recalled on power up.
Dip Switch 1
This switch enables local control using the dip-
switches. ON enables local control and makes
selections on the dipswitch active, and OFF
disables local control (locking out any local
changes)
Note.
When Switch 1 is initially switched to ON, the static
settings currently set on the dip-switches may not
reflect the actual configuration stored in the
module. This is because all settings can be
changed from the remote control system or via the
Service Adapter. This overrides the local dip
switches regardless of Switch 1 ON/OFF setting. To
ensure the module reads the local dip switch
settings it is recommended to toggle Switch 1 ON-
OFF-ON before making any local changes to the
dip switches.
Dip Switch 2
20 / 24 bit operation. When set to ON the AES audio
output will be 24 bits wide (which is normal). When
set to OFF the AES audio output can be set to 20
bits, which is sometimes necessary for downstream
equipment which may not be compatible with 24
bits operation.

Reference Manual P MX 3214 Version3.1
Page 19
Dip Switch 3
Delete embedded audio. When set to ON this will
delete ALL incoming AES audio signals on the input
SDI signal (if any). When set to OFF only the
channels selected for embedding (using SW2) will
be overwritten. Any remaining audio, which was
present on the incoming SDI signal will pass
transparently.
Dip Switch 4
Sample rate conversion ON/OFF. This is used to
select sample rate conversion for the module. This
setting applies both input audio signals. When set
to ON (asynchronous) all incoming audio will be
sample rate converted to 48 KHz. (input range
30KHz to 48KHz). When set to OFF the sample rate
conversion will be bypassed. If bypassed, all
incoming audio must be synchronous to the input
SDI signal. This is useful if the module is to work with
Dolby audio data where the audio should not be
resampled.
Dip Switch 5 through 8
Select Audio Groups. These four switches are used
to select which audio groups are to be embedded
into the incoming SDI video. ON selects the audio
group and OFF deselects it.
NOTE: If two groups are selected at the
same time, embedding is switched off
Auto Store
If no parameters are changed for 10 seconds then
the current settings will be written into flash memory
automatically, this can be seen by the front LED
flashing yellow four times.

Reference Manual P MX 3214 Version 3.1
Page 20
Factory Preset Condition
The P MX 3214 is delivered preset for the following
mode of operation:
1. ON: Local adjustments enabled
2. OFF: 20 bit AES
3. OFF: Only replace audio group selected
4. OFF: Sample rate conversion bypassed
5. ON: Audio Group 1 Selected (Embedder 1)
OFF: (Embedder 2)
6. OFF: (Embedder 1)
ON: Audio Group 2 Selected (Embedder 2)
7. OFF
8. OFF
If this is the mode of operation required, then no
adjustments are necessary.