Lynx L-325 User manual

4-Port ADSL Router
LYNX L-325
Quick Guide
Version 1.0

4-Port ADSL Router (Lynx L-325)
Quick Guide
1
Version 1.0
Document #: BD-AQ0007-10
Version Date: July 1, 2005
Document #: BD-AQ0007-10
Table of Contents
GENERAL INFORMATION ...............................................................2
Package Contents..................................................................2
Safety Instructions—Please read. ...........................................2
Front Panel View....................................................................3
Back Panel View ....................................................................4
INSTALLING THE ROUTER .............................................................5
Connect the ADSL Line and Telephone.................................5
Connect the PC to the Router ................................................5
Connect the Power Adapter ...................................................5
Installation Diagram ...............................................................6
CONFIGURING YOUR COMPUTER ..................................................7
Windows 2000........................................................................7
Windows XP...........................................................................8
LOG IN TO THE ROUTER................................................................9

4-Port ADSL Router (Lynx L-325)
Quick Guide
2
Version 1.0
Document #: BD-AQ0007-10
General Information
The 4-Port ADSL Router features 4 LAN ports for added
convenience and accessibility.
Package Contents
Included in the package is one of each of the following—
•4-Port ADSL router
•15 VAC AC power adapter
•RJ-11 telephone cable
•RJ-45 Ethernet cable
•Splitter
•User Manual
•Quick Guide
•Place your router on a flat surface close to the cables in a
location with sufficient ventilation.
•To prevent overheating, do not obstruct the ventilation
openings of this equipment.
•Plug this equipment into a surge protector to reduce the risk
of damage from power surges and lightning strikes.
•Operate this equipment only from an electrical outlet with
the correct power source as indicated on the adapter.
•Do not open the cover of this equipment. Opening the
cover will void any warranties on the equipment.
•Unplug equipment first before cleaning. A damp cloth can
be used to clean the equipment. Do not use liquid / aerosol
cleaners or magnetic / static cleaning devices.
Safety Instructions—Please read.

4-Port ADSL Router (Lynx L-325)
Quick Guide
3
Version 1.0
Document #: BD-AQ0007-10
Front Panel View
LED Mode Indication
Solid ADSL is connected.
No light ADSL is not connected.
DSL
Blinking The router is connected to ADSL.
.
Solid Router is connected to the LAN.
No light No connection to the LAN. Check if the
LAN cable is connected to the router.
LAN1-LAN4
Blinking LAN traffic
Solid PPP user id accepted
INT No light PPP not connected
Solid Router is powered on.
POWER No light
Router is not powered. Check if the
router is plugged in and if the power
switch is turned on.

4-Port ADSL Router (Lynx L-325)
Quick Guide
4
Version 1.0
Document #: BD-AQ0007-10
Back Panel View
Port Description
Power Switch Press to turn the router on and off.
Power Connects to a 15 VAC AC power adapter.
Reset
Restart —press the button for less than 4
seconds.
Default settings —press the button for 4
seconds or longer.
LAN1-LAN4 RJ-45 connects the unit to an Ethernet device
such as a PC or a switch.
Line For connecting to ADSL Service.

4-Port ADSL Router (Lynx L-325)
Quick Guide
5
Version 1.0
Document #: BD-AQ0007-10
Installing the Router
Connect the ADSL Line and Telephone
The “line” connection on the modem/router must not be
connected to a filter. If you need to share the phone jack with a
telephone, then use the splitter included with your modem/router.
NOTE: See connections on the installation diagram.
Connect the PC to the Router
Use the Ethernet cable to connect your computer directly to the
router. Connect one end of the Ethernet cable to one of the ports
labeled LAN on the rear panel of the router and connect the other
end to the Ethernet port of your computer. Attach any additional
PCs to the router using RJ-45 cables to the port labeled LAN on
the rear panel of the router.
Connect the Power Adapter
Complete the process by connecting the AC power adapter to the
POWER connector on the back of the device and plug the adapter
into a wall outlet or power strip. Then turn on and boot up your
PC and any LAN devices, such as hubs or switches, and any
computers connected to them.

4-Port ADSL Router (Lynx L-325)
Quick Guide
6
Version 1.0
Document #: BD-AQ0007-10
Installation Diagram

4-Port ADSL Router (Lynx L-325)
Quick Guide
7
Version 1.0
Document #: BD-AQ0007-10
Configuring Your Computer
Prior to accessing the router through the LAN port, note the
following necessary configurations—
•Your PC’s TCP/IP address: 192.168.1.__( the last number
is any number between 3 and 254)
•The router’s default IP address: 192.168.1.1
•Subnet mask: 255.255.255.0
Below are the procedures for configuring your computer. Follow
the instructions for the operating system that you are using.
Windows 2000
1. In the Windows taskbar, click on the Start button and point
to Settings, Control Panel, and Network and Dial-up
Connections (in that order).
2. Click on Local Area Connection. When you have the Local
Area Connection Status window open, click on Properties.
3. Listed in the window are the installed network components.
If the list includes Internet Protocol (TCP/IP), then the
protocol has already been enabled, and you can skip to
Step 10.
4. If Internet Protocol (TCP/IP) does not appear as an
installed component, then click on Install.
5. In the Select Network Component Type window, click on
protocol and then the Add button.
6. Select Internet Protocol (TCP/IP) from the list and then click
on OK.
7. If prompted to restart your computer with the new settings,
click OK.

4-Port ADSL Router (Lynx L-325)
Quick Guide
8
Version 1.0
Document #: BD-AQ0007-10
8. After your computer restarts, click on the Network and Dial-
up Connections icon again, and right click on the Local
Area Connection icon and then select Properties.
9. In the Local Area Connection Properties dialog box, select
Internet Protocol (TCP/IP) and then click on Properties.
10. In the Internet Protocol (TCP/IP) Properties dialog box,
click in the radio button labeled Use the following IP
address and type 192.168.1.x (where x is any number
between 2 and 254) and 255.255.255.0 in the IP address
field and Subnet Mask field.
11. Click on OK twice to save your changes and then close
the Control Panel.
Windows XP
1. In the Windows taskbar, click on the Start button and point
to Settings and then click Network Connections.
2. In the Network Connections window, right click on the Local
Area Connection icon and click on properties.
3. Listed in the Local Area Connection window are the
installed network components. Make sure the box for
Internet Protocol (TCP/IP) is checked and then click on
Properties.
4. In the Internet Protocol (TCP/IP) Properties dialog box, click
in the radio button labeled Use the following IP address and
type 192.168.1.x (where x is any number between 2 and
254) and 255.255.255.0 in the IP address field and Subnet
Mask field.
5. Click on OK twice to save your changes and then close the
Control Panel.

4-Port ADSL Router (Lynx L-325)
Quick Guide
9
Version 1.0
Document #: BD-AQ0007-10
Log in to the Router
This section explains how to log in to your router using the
following steps—
1. Launch your web browser.
2. Enter the URL http://192.168.1.1 in the address bar and click
on Enter.
A login screen like the one below will be displayed after you
connect to the user interface.
3. Enter your user name and password, and then click on OK
to display the user interface.
NOTE: There are two default user name and password
combinations. The user / user combination can display device
status, but cannot change or save configurations and are limited
to only certain screens. The admin / admin combination can
perform all functions. Passwords can be changed at any time.
The following manual shows configurations based on the admin /
admin log in.