Lyyt 153.743UK User manual

153.743UK User Manual
RGB/RGBW Sound Active Controller
Item ref: 153.743UK User Manual
Wireless controller for RGB/RGBW multi-colour LED tape with a 24-key handheld remote. Capable of operating 12V or
24V tape with up to 5A per channel (R/G/B) or 4A (R/G/B/W). Options for 8 static colours, 3 auto sequences with speed
control or 3 sound-activated sequences from an internal microphone or 3.5mm audio input with sensitivity control.
Operating with this controller enables RGB/RGBW tape to give sound-reactive colour to architectural features or signage.
Note: This controller can operate with 12V or 24V LED tape up to 5A maximum output per channel for R/G/B tape (15A
total) and up to 4A maximum output per channel for R/G/B/W tape (16A total). For longer runs of RGB and RGBW tape
with higher current requirements, RGB/RGBW amplifiers with additional power supplies will be necessary.
If you have bought one of our LED Tape kits, you will have been supplied with a 4-pin lead to connect to connect to
RBG/RGBW tape from the controller. Strip the wires for R / G / B / W / V+ and connect to the relative screw terminals on
the controller. If you haven’t bought one of our LED Tape kits, you will have to purchase this lead separately.
Main Unit Specification:
Working temperature
-20-60℃
Supply voltage
DC5V-24V
Static power consumption
<1W
Connecting mode
common anode
Grayscale
1024 levels (RGB each)
Speed stage
100 graduations
External dimension
L72*W42*20mm
Packing size
L92*W56*H32 mm
Net weight
52g
Gross weight
81g
Output
3/4 channels
Max. Output current
3*5A(RGB)/4*4A(RGBW)
RF frequency
433.92Mhz
Remote distance
Up to 20M
PWM frequency
1.95KHz
Memory function
Yes
Short-circuit protection
Yes
Max. Output power
80W(5V); 192W(12V); 384W(24V)
RF Remote-Control Specification:
Version 1.0
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Working temperature
-20℃~45℃
Supply voltage
DC3V（CR2025）
Standby current
3.3uA
Working current
12mA
Standby power
9.9uW
Working power
36mW
Net weight
25g
RF frequency
433.92MHz
External dimension
L85*W51*H6mm
RF distance
≤20m

153.743UK User Manual
Main Unit Layout:
RF Remote Control Layout:
Setting up:
Connect the +V, R, G, B (and W if using RGBW tape) output to the LED tape using a connection lead, ensuring that all
terminals are fed to the correct connections on the tape. Connect 12Vdc or 24Vdc power to the DC5521 jack input or DC
power input terminals, ensuring that both power supply and controller have enough current capacity to operate the
connected tape.
Remove the plastic tab from the handheld RF remote control unit to activate the battery (Button cell CR2025). Power up
the main control unit from the 12Vdc or 24Vdc power supply and if the LEDs are not lit, press the power ‘ON’ key on the
remote control.
Use the ‘SET’ button to set the controller according to the type of LED tape being used. The indicator light will flash
slowly for RGB tape and flash fast for RGBW tape setting.
Select static colours by pressing one of the colour keys on the remote control. Use the two brightness keys to adjust the
brightness of the LED’s. A short press on the W key will switch the white LED light on/off. A long press on the W key will
dim the white LED light.

153.743UK User Manual
Preset auto sequences can be selected by pressing FLASH, BLOOM or SMOOTH keys. The speed of the selected preset
can be adjusted using the SPEED+/SPEED- keys.
The controller has 3 sound activated modes:
1. Press the F.T. key for a sound activated colour flash effect
2. Press the M.T. key for a sound activated colour morph effect
3. Press the C.T. key for a sound activated colour scroll effect
Two Color balance keys enable manual setting any of 1024 colours by stepping up or down through them incrementally.
DIY 1 & 2: A long press on either DIY key for 3 seconds will store a new light colour setting, created using the colour
balance keys. A short press will then activate the preset colour setting for that key.
Sound activated presets will be triggered by sound captured by the internal microphone. Alternatively, a line level audio
source may be connected to the 3.5mm audio input jack.
Sound activated triggering is adjusted using the rotary sensitivity control. To switch off the LEDs temporarily, press the
OFF key, then press ON to switch back on. If not being used for long periods, it is better to switch off the 12Vdc or 24Vdc
power supply.
Application Circuit RGB:
Application Circuit RGBW:
Warning:
•For reasons of electrical safety, this device must never be immersed in water, exposed to damp conditions or
excessive force.
•Do not use this device if you find that it is damaged in any way.
•Do not attempt to repair this device or take apart under any circumstances, as this will invalidate your warranty.

153.743UK User Manual
Pairing the RF remote control handset
Each controller is supplied with an RF handheld remote control that has been uniquely coded to work with the controller.
In some circumstances, it might be useful to operate several controllers independently from separate remote controls.
The controller can be paired to a remote control using either of the following two methods…
Method 1:
Step 1: Press and hold the “FLASH” key, power on the controller, the LEDs will be 50% brightness white to confirm.
Step 2: Press the “FLASH” key 3 times within 3 seconds, the LEDs will change 25%-10%, then back to preset level.
Once the above process is completed, the controller should operate remotely from the paired handset.
If pairing is not successful, re-try by repeating steps 1 and 2 above.
Method 2:
Step 1: Once all connections are made, power up the controller.
Step 2: Press and hold the “SET” button on the receiver for 5 seconds until the indicator light lights up.
Step 3: Hold down the “SET”button on the controller and press “FLASH” on the remote control once to finish
The LED tape will flash 3 times to confirm.
Once the above process is completed, the controller should operate remotely from the paired handset.
If pairing is not successful, re-try by repeating steps 1 to 3 above.
Clearing pairing of RF remote control handsets
To revert remote control pairing back to the factory default, follow one of the two methods below.
Method 1:
Step 1: Press and hold the “SMOOTH” key, power on the controller, the LEDs will be 50% brightness white to confirm.
Step 2: Press the “SMOOTH” key 3 times within 3 seconds, the LEDs will change 25%-10%, then back to preset level.
If the pairing is cleared successfully, the receiver can be controlled by any remote control.
If pairing is not cleared successfully, re-try by repeating steps 1 and 2 above.
Method 2:
Step 1: Once all connections are made, power up the controller.
Step 2: Press and hold the “SET” button on the receiver for 5 seconds until the indicator light lights up.
Step 3: Hold down the “SET”button on the controller and press “SMOOTH” on the remote control once to finish
The LED tape will flash 3 times to confirm.
Once the above process is completed, the controller should operate remotely from the paired handset.
If pairing is not successful, re-try by repeating steps 1 to 3 above.
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as
Electrical or Electronic equipment and should not be disposed with other household or commercial waste
at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Hereby, AVSL Group Ltd. declares that the radio equipment type 153.743UK is in compliance with
Directive 2014/53/EU
The full text of the EU declaration of conformity is available at the following internet address:
http://www.avsl.com/assets/exportdoc/1/5/153743UK%20CE.pdf
Errors and omissions excepted. Copyright© 2022. AVSL Group Ltd.
Unit 2-4 Bridgewater Park, Taylor Rd. Manchester. M41 7JQ
AVSL (EUROPE) Ltd, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, Ireland