M-system R30SVF4 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9023 Rev.1 P. 1 / 5
INSTRUCTION MANUAL
HIGH-SPEED DC VOLTAGE/CURRENT INPUT MODULE
(4 points, isolated) MODEL R30SVF4
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
High-speed DC voltage/current input module...................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
•The equipment must be mounted inside the instrument
panel of a metal enclosure.
•The actual installation environments such as panel con-
figurations, connected devices and connected wires may
affect the protection level of this unit when it is integrat-
ed in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure CE conformity.
■GENERAL PRECAUTIONS
•Before you remove the terminal block or mount it, turn off
input signals for safety.
■HOT INSERTION/REMOVAL OF MODULES
•It is possible to replace the module with the power sup-
plied, provided that modules are of the same model num-
ber and that the same Installation Base slot is used.
•Turn off input signals before replacing the module for
safety. Note that replacing multiple modules at once may
greatly change line voltage levels. We recommend that
you replace them one by one.
■UNUSED CHANNEL
•Set unused channels to “CH disabled” with PC Configura-
tor software: R30CFG. When input range is 1 to 5 V DC
or 4 to 20 mA DC, input values of the unused channels left
open are to be lower than -15 %, which set a data error at
the PLC or other host devices.
■ENVIRONMENT
•Indoor use.
•When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
•Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
•Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
•Be sure to attach the terminal cover for safety.
■AND ....
•The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.

R30SVF4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9023 Rev.1 P. 2 / 5
COMPONENT IDENTIFICATION
RUN
ERR
RUN LED
Input Terminal Block
ERR LED
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Lock Tab
Base Fixing Screw
Specifications
Positioning Guide
Terminal Cover
Terminal Fixing Screw
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
■STATUS INDICATORS
LED COLOR FUNCTION
RUN indicator Green ON while network module operates normally
OFF in network module error
ERR indicator Red OFF when input circuit and internal bus operate normally
Blinks in 1 sec. cycles with input value error (≤ -15%, ≥ +115%).
Blinks in 400 msec. cycles with input circuit error (AD converter response failure).
ON with internal bus error
■TERMINAL ASSIGNMENTS
NO. ID FUNCTION NO. ID FUNCTION
1 VL1 Narrow span volt. 1 11 VH1 Wide span volt. 1
2 I1 Current 1 12 COM1 Common 1
3 VL2 Narrow span volt. 2 13 VH2 Wide span volt. 2
4 I2 Current 2 14 COM2 Common 2
5 NC No connection 15 NC No connection
6 VL3 Narrow span volt. 3 16 VH3 Wide span volt. 3
7 I3 Current 3 17 COM3 Common 3
8 VL4 Narrow span volt. 4 18 VH4 Wide span volt. 4
9 I4 Current 4 19 COM4 Common 4
10 NC No connection 20 NC No connection
11
VH1
12
COM1
13
VH2
14
COM2
15
NC
16
VH3
17
COM3
18
VH4
19
COM4
20
NC
1
VL1
2
I1
3
VL2
4
I2
5
NC
6
VL3
7
I3
8
VL4
9
I4
10
NC

R30SVF4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9023 Rev.1 P. 3 / 5
INSTALLATION
■INSTALLATION TO THE BASE
Use the Installation Base (model: R30BS).
The I/O slots are numbered in the ascending order starting
from the one on the immediate right side of the network
module (slot 1, slot 2...).
A code indicating the I/O slot number is assigned to each
I/O slot and I/O data is allocated in the order of this code.
When an I/O slot is vacant, blank data is sent or received to/
from the PLC, etc.
■
PWR COM I/O1 I/O n
HOW TO MOUNT THE MODULE ON THE BASE
1) Engage the positioning guide of the module with the In-
stallation Base.
2) Pivot the module on the positioning guide and press it
down until the lock tab sits into place.
Positioning Guide
3) Tighten the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more) (torque 0.5 N·m).
Base Fixing Screw
■HOW TO REMOVE THE MODULE
1) Loosen the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more).
Base Fixing Screw
2) While pressing the projection on the lock tab, push the
module upward.
3) Detach the positioning guide of the module from the In-
stallation Base.
Lock Tab

R30SVF4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9023 Rev.1 P. 4 / 5
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
①
②
③
④
⑪
⑫
⑬
⑭⑤
⑥
⑦
⑧
⑨
⑩
⑮
⑯
⑰
⑱
⑲
⑳
110 (4.33)
25 (.98) 98 (3.86)
20–M3
SCREW
6
(.24)
■CONNECTION DIAGRAM
■INPUT RANGE
•Wide span voltage : -10 – +10 V DC, -5 – +5 V DC,
0 – 10 V DC, 0 – 5 V DC,
1 – 5 V DC
•Narrow span voltage: -1 – +1 V DC, 0 – 1 V DC,
-0.5 – +0.5 V DC
•Current : -20 – +20 mA DC, 0 – 20 mA DC,
4 – 20 mA DC
11
VH1
VL1
I1
COM1
2
12
1
18
9
19
8
VH4
VL4
I4
COM4
13
VH2
VL2
I2
COM2
4
14
3
16
VH3
VL3
I3
COM3
7
17
6
■Input Connection Examples
VHn
In
COMn
VLn
Wide Span
Voltage
+
–
Narrow Span
Voltage
+
–
Current
+
–
VHn
In
COMn
VLn
VHn
In
COMn
VLn
Note: Connect either wide or narrow span or current terminals for each channel.
Note: Be sure to close across VLn and In terminals for a current input.
Input 1
Input 2
Input 3
Input 4
INTERNAL POWER
INTERNAL BUS
BUS CONNECTOR

R30SVF4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9023 Rev.1 P. 5 / 5
WIRING INSTRUCTIONS
■TORQUE
Wiring screw for separable terminal: 0.5 N·m
Fixing screw for separable terminal: 0.5 N·m
■SOLDERLESS TERMINAL unit: mm
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit.
Recommended manufacturer: Japan Solderless Terminal
MFG.Co., Ltd., Nichifu Co., Ltd.
Applicable wire size: 0.25 – 0.75 mm2
12 max.
6 max.
3 max.
3.2 dia.
■HOW TO REMOVE SEPARABLE SCREW TERMINAL
The terminal block is separable in two pieces. Evenly loos-
en two screws on top and bottom of the terminal block to
separate.
CONFIGURATOR SOFTWARE SETTING
With configurator software, settings shown below are avail-
able. Refer to the software manual of R30CFG for detailed
operation.
■CHANNEL INDIVIDUAL SETTING
ITEM USABLE RANGE DEFAULT
SETTING
Unused setting CH enabled
CH disabled
CH enabled
Input range -10 – +10 V DC
-5 – +5 V DC
-1 – +1 V DC
0 – 10 V DC
0 – 5 V DC
1 – 5 V DC
0 – 1 V DC
-0.5 – +0.5 V DC
-20 – +20 mA DC
4 – 20 mA DC
0 – 20 mA DC
-10 – +10 V DC
Fine zero adjustment -320.00 – +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 – +3.2000 1.0000
Scaled range Zero -32 000 – +32 000 0
Scaled range Span -32 000 – [phone]
■CHANNEL BATCH SETTING
ITEM USABLE RANGE DEFAULT
SETTING
Averaging number 1, 2, 4, 8, 16, 32, 64,
128, 256
1
Simulate input Normal input
Simulated data
Normal input