M-system R3S-YV4 User manual

R3S-YV4
P. 1 / 3EM-8940
DC VOLTAGE OUTPUT MODULE
(4 points, isolated) MODEL R3S-YV4
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage output module ........................................... (1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■HOT INSERTION/REMOVAL OF MODULES
Removing or replacing modules does not affect other mod-
ules on the same backplane. It is possible to replace them
without removing the power supply. However, replacing
multiple modules at once may greatly change line voltage
levels. We recommend that you replace them one by one.
■ENVIRONMENT
•Indooruse
•Whenheavydustormetalparticlesarepresentintheair,
install the unit inside proper housing with sufficient ven-
tilation.
•Donotinstalltheunitwhereitissubjectedtocontinuous
vibration.Donotsubjecttheunittophysicalimpact.
•Environmentaltemperaturemustbewithin-10to+55°C
(14to131°F)withrelativehumiditywithin30to90%RH
in order to ensure adequate life span and operation.
■WIRING
•Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
The unit is designed to function as soon as power is sup-
plied,however,awarmupfor10minutesisrequiredforsat-
isfying complete performance described in the data sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).

R3S-YV4
P. 2 / 3EM-8940
■STATUS INDICATOR LED
RUN indicator:Bi-color(red/green)LED;
RedwhenthebusAoperatesnormally;
GreenwhenthebusBoperatesnormally;
Amber when both buses operate normally.
ERR indicator:GreenLEDturnsoninnormaloperating
conditions.
COMPONENT IDENTIFICATION
■SIDE DIP SW
• Output Range: SW1, SW2
OUTPUT 1 (SW1) OUTPUT 2 (SW1)
RANGE
OUTPUT 3 (SW2) OUTPUT 4 (SW2)
12345678
OFF OFF OFF OFF OFF OFF OFF OFF
-10–+10V(*)
ON OFF OFF OFF ON OFF OFF OFF
-5–+5V
OFF ON OFF OFF OFF ON OFF OFF
-1–+1V
ON ON OFF OFF ON ON OFF OFF
0–10V
OFF OFF ON OFF OFF OFF ON OFF
0–5V
ON OFF ON OFF ON OFF ON OFF
1–5V
OFF ON ON OFF OFF ON ON OFF
0–1V
• Output Hold: SW3
SW OUTPUT HOLD
HOLD (*)OFF
SW3-1 OFF ON
(*)Factorysetting
1
20
ON
8
7
6
5
4
3
2
1
SW1SW2
ON
8
7
6
5
4
3
2
1
SW3
ON
4
3
2
1
■ FRONT VIEW ■ SIDE VIEW
ERR LED
RUN LED
Output
Hold
Output 2 (SW1)
or
Output 4 (SW2)
Range
Output 1 (SW1)
or
Output 3 (SW2)
Functions
■DIMENSIONS mm (inch)
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
1
20
130 (5.12)
27.5 (1.08) 109 (4.29)
120 (4.72)
POSITIONING
GUIDE

R3S-YV4
P. 3 / 3EM-8940
■CONNECTION DIAGRAM
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: [phone], Fax: [phone], E-mail: [e-mail]
*1. For dual redundant communication.
*2. To use shield line, connect it to SLD terminal and ground the terminal 20.
Note: Do not connect wide span and narrow span simultaneously within the same channel.
Do not use void terminals.
1
INTERNAL POWER
+
–
+
WIDE SPAN
NARROW SPAN
OUTPUT 1
3
2
5+
–
+
WIDE SPAN
NARROW SPAN
OUTPUT 2
7
6
11
+
–
+
WIDE SPAN
NARROW SPAN
OUTPUT 3
13
12
15
+
–
+
WIDE SPAN
NARROW SPAN
OUTPUT 4
17
16
SLD
SLD
SLD
SLD
SLD
SLD
*2
4
8
18
19
20
14
BUS A
BUS B*1
BUS CONNECTOR
WIRING INSTRUCTIONS
■APPLICABLE WIRE SIZE mm
• Solid: 0.2to1.0mm2(0.55to1.12dia.)
• Stranded:0.2to1.5mm2
(Tinning wire ends may cause contact failure and therefore
is not recommended.)
• Ferruled:
Unsheathed:0.25to1.5mm2
Sheathed:0.25to0.75mm2
•Exposewireconductorsby10mm(0.39”).
■CONNECTION PROCEDURE
Insert the wire end until it comes to a full stop while push-
ing slot with the tip of a screw driver as shown below. Be
sure wire insulation is not inside the terminal.
Screw Driver
Power wire
Stripped length
10mm
OUTPUT PIN ASSIGNMENT
PIN No. FUNCTION
1V
H1
2C
OM1
3 VL1
4 SLD
5V
H2
6C
OM2
7 VL2
8 SLD
9N
C
10 NC
11 VH3
12 COM3
13 VL3
14 SLD
15 VH4
16 COM4
17 VL4
18 SLD
19 SLD
20 SLD