M-TI WIRELESS EDGE Series User manual

SHEET 2 OF 4
WIRELESS EDGE
RD41169400C/REV-E
(MT-120018/A
ONLY)
ELEVATION
x4
x4
Us tight ning torqu of 5.7N/m.
1
2 3
in it m 1 is align d with th l vation axis.
AXIS
14
x4
Attach it m 1 to th back of th nclosur
using it ms2, 3, 13 as shown.
V rify that th oriantation of th hol
For radio in 45
us this s t of hol s
in it m 1 is align d with th l vation axis.
1
BASE BRACKET INSTALLATION TO ANTENNA
AXIS
ELEVATION
x4 x4
x4
Us tight ning torqu of 5.7N/m.
234
Attach it m 1 to th back of th ant nna
using it ms 2,3,4 as shown.
V rify that th oriantation of th hol
BASE BRACKET INSTALLATION
TO ENCLOSURE
11
Hamelacha St
. ,
Afek Indust ial Pa k, Rosh
Ha’ayin
48091
, Is ael
Fax: [phone], Tel: [phone]
www.mtiwe.com

x2
11
8
9x2
x2
12or6
RADIO ENCLOSURE
Use tightening torque of 24 N m.
socket on item 1.
Note: The bolt head shall be positioned in the
surfaces) using item 6,7,8,9 as shown.
Connect item 10 to item 1 (mate knurled
Use tightening torque of 14N m.
small pole diameter use item 6 instead of item 12).
Step 1
Connect the base bracket as shown on page 2.
STEP 2 (FOR POLES SIZES 1.75"-3")
Install the antenna to the pole using item 11,
tighten the bracket using items 8,9,12 (for
ANTENNA OR
INSTALLATION ON A POLE
SHEET 3 OF 4
WIRELESS EDGE
RD41169400C REV-E
6
1
10
789
ANTENNA OR RADIO
ENCLOSURE
11
Hamelacha St
. ,
Afek Industrial Park, Rosh
Ha ayin
48091
, Israel
Fax: [phone], Tel: [phone]
www.mtiwe.com

SHEET 4 OF 4
WIRELESS EDGE
RD41169400C/REV-E
Elevation
axis
holes ( Har ware
not supplie )
in the socket of item 5.
Use tightening torque of 24 N/m to the azimuth
987
6
6
7 8
an elevation har ware.
MOUNTING ON A WALL
1
5
10
9
Connect base bracket as shown on page 2
Connect item 5 to item 1 (mate the knurle
surfaces) using items 6,7,8,9 as shown.
Note: the bolt hea shall be positione in the
socket of item 1.
mount item 10 on the wall on the esire position.
(note the azimuth axis oriantation)
Attach item 5 to the arm bracket item 10 (mate the
knurel surfaces) using items 6,7,8,9 as
shown. Note the bolt hea shall be positione
Wall mounting
Azimuth
axis
x2x2
12 9 8
Use tightening torque of 14N/m.
11
STEP 2 (FOR POLES SIZES 1"-1.75")
Install the antenna to the pole using
item 11 as shown, tighten the bracket
using items 8,9,12.
x2
11
Hamelacha St
. ,
Afek Industrial ark, Rosh
Ha’ayin
48091
, Israel
Fax: [phone], Tel: [phone]
www.mtiwe.com

Clamping bracket
Qty: 1
Qty: 4
Flat washer M5
Item:2
SHEET 1 OF 4
WIRELESS EDGE
D41169400C/ EV-E
Qty: 1
Antenna/enclosure
base bracket
Item: 1
Bolt M8x40
Qty: 4
Washer flat M8
Qty: 4
Arm bracket
Qty: 1
Wall/Poll bracket
Qty: 1
Bolt M8x70
Qty: 2
Bolt M5x16
Qty: 4
MT-120018/A only
Washer spring M8
Qty: 4
Nut M8
Qty: 2
Qty: 4
Spring washer M5
Item: 3
Item: 9
Item: 11
Qty: 4
Nut M5
Item: 13
MT-120018 AND MT-120018/A
Item: 4
Item: 5
Item: 10
Item: 8
Item: 6
Item: 12
INSTALLATION INSTRUCTIONS
FOR
Item: 7
11
H mel ch St
. ,
Afek Industri l P rk, Rosh
H ’ yin
48091
, Isr el
F x: 972-3-9025051, Tel: [phone]
www.mtiwe.com