M2 Antenna Systems FGHM64 User manual

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722
Tel: [phone] Fax: [phone] Web: www.m2inc.com
©2019 M2 Antenna Systems Incorporated 08/01/19
Rev.03
M2 Antenna Systems, Inc.
Model No: FGHM64
PORTABLE HITCH MAST
Model .........................................FGHM64
Collapsed Size ...........................74”
Extended Size ............................288.50”
Mast Size....................................2”, 1-3/4”, 1-1/2, 1-1/4” & 1”
Weight ........................................16 Lbs.
Material.......................................Aluminum 6061-T6
FEATURES:
The M2 FGHM64 is a portable telescoping mast designed to fit a standard 2” hitch receivers for portable and
quick deploy operations. The unit will collapse down to 74” for ease of transport. No assembly required.

FGHM64 SYSTEM LAYOUT (EXAMPLE)
NOTE:
SHOWN FULLY EXTENDED
WITH ANTENNAS
NOTE:
SHOWN COLLAPSED
WITH ANTENNAS
NOTE:
Optional overhead guy support kit available
for additional tie down support if needed.
440-6SS
23CM22EZA
2M-3SS
6M-3SS

FGHM64 MAST CLAMP ASSEMBLY
BOLT, 1/4-28 X 1-3/4”,SS
NOTE:
TIGHTEN OR LOOSEN BOLT
TO ADJUST CLAMP TENSION.

FGHM64 HITCH BASE DETAILS
M2 ANTENNA SYSTEMS, INC.
4402 N. SELLAND AVE.
FRESNO, CA 93722
Ph. [phone] www.m2inc.com Email: [email protected]m
NOTE:
The FGHM64 has been designed to fit most
standard 2” hitch receivers. Slip hitch base
assembly into your hitch receiver and secure
with one on each side: Bolt, 1/2-20 X 1” and 1/2”
lock washer.

FGHM64 OPERATION DETAILS
Raising the mast
Carefully raise one section at a time. Begin with the smaller 1” tubing. Look for indicating
marks on tube to help line up your locking pins with pin holes. Repeat the following
procedure for the remaining sections.
Azimuth rotation
Manual rotation provided using the clamp assembly locking lever. Simply release lever,
turn system to desired position and lock lever.
Lowering the mast
CAUTION: LOWER YOUR MAST SLOWLY AND CAREFULLY! DO NOT LET THE
SYSTEM SLAM DOWN. THIS MAY CAUSE SERIOUS PERSONAL INJURY, DAMAGE
ANTENNAS AND MAST.
Lower one section at a time. Begin with the bigger 2” tube. Repeat procedure for the
following smaller tube sections.

FGHM64 PARTS & HARDWARE
DESCRIPTION......................................................................................... QTY
HITCH BASE ASSEMBY (SAMS6400) ................................................... 1
TELESCOPING MAST ASSEMBLY (SAMS6402) ................................... 1
MAST CLAMP (M2AMP6403).................................................................. 1
MAST CRADLE (M2AMP6407)................................................................ 1
MAST CRADLE WITH HOLES (M2AMP6404) ........................................ 1
PIVOT CLAMP ARM (M2AMP6406) ........................................................ 1
PIVOT CLAMP JOINT ( M2AMP6405)..................................................... 1
ASSEMBLY MANUAL .............................................................................. 1
HARDWARE............................................................................................ QTY
BOLT, 1/4-20 X 2-3/4”,SS ........................................................................ 2
BOLT, 1/4-28 X 1-3/4”,SS ........................................................................ 1
BOLT, 1/4-20 X 1-1/2”,SS ........................................................................ 2
BOLT, 1/2-20 X 1”, SS ............................................................................. 2
LOCKWASHER, 1/2”, SS......................................................................... 2
LOCKWASHER, 1/4”, SS......................................................................... 4
OPTIONAL GUY SUPPORT KIT............................................................. QTY
SUPPORT PLATE (M2AMP6408)............................................................ 1
DACRON ROPE, 3/32 X 30’ .................................................................... 4
STAKE, 12” .............................................................................................. 4
OPTIONAL BTM KIT ............................................................................... QTY
BTM PLATE, 3” X .125 X 4” (M2APT6966) .............................................. 1
UNI CRADLE, 3/4 X 1/2 X 3, (M2AMC0076)............................................ 2
U-BOLT, 2”, SS ........................................................................................ 2
U-BOLT & CRADLE, 1-1/2”...................................................................... 2
U-BOLT, 1”............................................................................................... 2
LOCKWASHER, 5/16, SS ........................................................................ 4
NUT, 5/16-18, SS..................................................................................... 4
LOCKWASHER, 1/4, SS .......................................................................... 8
NUT, 1/4-20, SS....................................................................................... 8
M2 ANTENNA SYSTEMS, INC.
4402 N. SELLAND AVE.
FRESNO, CA 93722
[phone] FAX: [phone]
www.m2inc.com Email: [e-mail]