Macrom M-OF7030 User manual

USER MANUAL
M-OF7030
M-OF7040
M-OF7050
DOP User manual_ENG.indd 1 14/11/2013 12:05:00

- 1 -
Safety Precautions
Never expose this unit, amplifier, and
speakers to moisture or water to prevent
electric sparks or fire.
Please don't change the fuse on the power
cord without professional guidance, using
improper fuse may cause damage to this unit
or even cause fire.
Please contact your nearest dealer if one of
the following symptoms is experienced:
(a). Water or other objects enters the unit.
(b). There is smoke.
(c). Peculiar smell.
Only connect the unit to a 12-volt power
supply with negative grounding.
MUTE
OK
MUTE
OK
Never install this unit where the operation &
condition for safe driving is impaired.
Never use the video display function in the
front when driving to prevent the violation of
laws & regulations and also to reduce the
risk of traffic accident except for using rear
view video camera.
MUTE
OK
MUTE
OK
MUTE
OK
MUTE
OK
Thank you for purchasing this product. Please
read through these operating instructions
so you will know how to operate your model
properly. After you’ve finished reading the
instructions, keep this manual in a safe place
for future reference.
To ensure safe driving, please adjust the
volume to a safe and comfortable level in
case of emergency situations.
DOP User manual_ENG.indd 1 14/11/2013 12:05:02

- 2 -
1. Never disassemble or adjust the unit without any professional guidance.
For details, please consult any professional car shop / dealer for inquiry.
2. If the front panel or TFT monitor is dirty, please use a clean silicone cloth and neutral detergent
to wipe off the spot. Using a rough cloth and non-neutral detergent such as alcohol for cleaning
may result in scratching or decoloration to the monitor.
3. If any abnormal behavior of the unit is found, please refer to trouble shooting guide of this
manual. If no relevant information is found, please press the [RESET] key on the front panel to
resume factory default.
4. If you have parked the car in hot or cold weather for a long time, please wait until the
temperature in the car becomes normal before operating the unit.
5. Using the car heater in low temperature environment may result in moisture inside the unit, DO
NOT use the unit in this situation. Eject the disc and wipe off the moisture on the disc. If the unit
still doesn't work after a few hours, please contact the service center.
6. Do not impact the LCD monitor which could cause damage.
7. To prevent damage to the screen, avoid touching it with sharp objects.
8. To provide a clear demonstration and an alternative for easy understanding to the operation of
this unit, graphic illustrations are used.
However, some illustrations are different from the actual images displayed on the screen.
9. Operate the unit correctly according to this manual to prevent unnecessary problem. The
guarantee won't be valid if the problem is caused by inappropriate operation.
Safety Precautions
Note:
The items listed outside of the frame are the commercial products generally sold.
Expanding System
SD Card
Power
Amplifier Rear
Monitor
Portable player
(connected via AV Input)
USB
memory
Bluetooth
cellular phone
Expanding audio feautres
HEAD UNIT
Expanding visual feautres
DOP User manual_ENG.indd 2 14/11/2013 12:05:02

- 3 -
Contents
Safety Precautions ....................................1-2
Expanding System ........................................ 2
Contents ........................................................ 3
Produc overview ........................................... 4
M-OF7030 Front Panel ............................ 4
M-OF7040 Front panel ............................. 5
M-OF7050 Front view ............................... 6
Remote control overview ............................. 7
Front view ................................................. 7
Back view .................................................. 8
Touch Screen ................................................ 8
Basic Operations .......................................... 9
Detect parking brake................................ 9
Mute .......................................................... 9
Power On / Off .......................................... 9
Audible Beep confirmation ...................... 9
Playing Source selection .......................... 9
EQ menu ................................................. 10
Select preset equalizer .......................... 10
Adjust EQ parameters ............................ 10
Adjust FAD /BAL ..................................... 10
Setting Date /Time ...................................... 11
Date ......................................................... 11
Clock mode ............................................. 11
Time ........................................................ 11
Desk timer .............................................. 11
Power off timer ....................................... 11
Radio Mode ................................................. 12
Tuner TFT isplay ..................................... 12
Select radio as playing source ............... 12
Select one radio band ............................ 12
Tune the radio......................................... 12
Preset station ......................................... 13
Local seeking .......................................... 13
RDS basic ................................................ 13
Adjust RDS settings ................................ 13
RDS ( Radio Data System ) ..................... 14
EON ......................................................... 14
TA function .............................................. 14
PTY function ............................................ 14
Playback Mode ........................................... 15
Load a disc .............................................. 15
Eject a disc .............................................. 15
Controlling playback .............................. 15
Connect a USB device ............................ 15
Remove a USB device ............................ 15
Insert a SD/MMC Card ........................... 15
Remove a SD/MMC card ........................ 15
Play/Pause .............................................. 15
Previous/Next ......................................... 15
Search for a folder ................................. 16
Repeat ..................................................... 16
Repeat A-B ............................................. 17
Shuffle (Random) oplay .......................... 17
Select audio mode .................................. 17
Select subtitle language ........................ 17
Change viewing angle ............................ 17
Playback information ............................. 18
Direct track entry ................................... 18
Rotate pictures ....................................... 18
Zoom ....................................................... 18
Video Setup ............................................. 18
Bluetooth Mode .......................................... 19
Pair the Bluetooth-enabled devices ...... 19
Disconnect Bluetooth device ................. 19
Make a call.............................................. 20
Incoming call .......................................... 21
Adjust Bluetooth settings ....................... 21
Bluetooth Musci mode ........................... 22
Steering wheel control ............................... 22
Programming SWC ................................ 22
Settings ....................................................... 22
General ................................................... 22
Calibration .............................................. 22
Adjust time .............................................. 22
Sound ...................................................... 23
Video ........................................................ 23
DVD ......................................................... 24
Volume .................................................... 24
Reset ....................................................... 24
Informations ............................................... 25
Other devices .......................................... 25
Reset ....................................................... 25
Replace a fuse ........................................ 25
Navigation (GPS) ..................................... 25
Specifications ............................................. 27
Products specifictions ............................ 27
Supported formats ................................. 28
Unsupported formats ............................. 28
Supported MP3 disc formats ................. 28
Supported video formats ........................ 28
Region code ............................................ 28
Precautions when using disc ................. 28
Wire connections ........................................ 29
M-OF7030 ............................................... 29
M-OF7040 ............................................... 30
M-OF7050 ............................................... 31
DOP User manual_ENG.indd 3 14/11/2013 12:05:03

- 4 -
Front panel
1. [MENU] Button
Press to switch between the available audio/video sources applied to the unit.
2. [ ] Button
Adjust screen brightness (press) Black screen (long press).
3. [VOL/ / ] Knob
Press to turn the unit ON. Press and hold to turn the unit OFF.
Rotate to adjust the volume. Press momentarily to activate the MUTE function. Press again to
resume normal listening.
Press the [
SRC
4
1
5
6
3
2
7
13
12
11
10
9
8
1416 1517
] key rotate the knob adjust the screen brightness
4. Map Slot
The SD card is used for the Navigation Map only, not for music or other files.
5. USB port
Connect a USB device for playback of music/video files.
6. A/V Input
Accepts a 3.5mm jack through which signals from various audio/video devices can be
applied to the unit.
7. Reset Button
Press to reset system settings to factory default (except password and parental lock
settings).
8. [ ] Button
Press to eject a disc.
9. Disc slot
10. Navigation
Press to switch to navigation mode.
11. Internal Microphone
Internal microphone for Bluetooth calls.
M-OF7030 Product overview
Notice:
The graphic in this manual is for reference only, and may be different from the actual unit.
1
11 10 9
2
3
4
56
7
8
DOP User manual_ENG.indd 4 14/11/2013 12:05:04

- 5 -
Front panel
M-OF7040 Product overview
Notice:
The graphic in this manual is for reference only, and may be different from the actual unit.
1
11
10
9
2
3
4
5
67
8
12
131415
1. [VOL/ / ] Knob
Press to turn the unit ON. Press and hold to turn the unit OFF.
Rotate to adjust the volume. Press momentarily to activate the MUTE function. Press again to
resume normal listening.
Press the [ ] key rotate the knob adjust the screen brightness
2. [ ] Button: Press to eject a disc.
3. [MENU] Button: Press to switch between the available audio/video sources applied to the unit.
4. Navigation: Press to switch to navigation mode.
5. SD/SDHC card slot: Insert an SD card for playback of music/video/picture files.
6. Map Slot: The SD card is used for the Navigation Map only, not for music or other files.
7. A/V Input. Accepts a 3.5mm jack through which signals from various audio/video
devices can be applied to the unit.
8. USB port:Connect a USB device for playback of music/video files.
7. Reset Button: Press to reset system settings to factory default (except password and
parental lock settings).
9. [BT] Button: Enter the Bluetooth Mode.
10. [ ] Button: Adjust screen brightness (press) Black screen (long press).
11. [FM/AM] Button: Press to enter the radio Mode. Press to switch radio band.
12. [ TUNE / SEL ] knob:
Rotate to select next/previous track or preset station.
Play/pause(press). Enter EQ setting(long press).
13. Reset Button: Press to reset system settings to factory default (except password and parental
lock settings).
14. Internal Microphone: Internal microphone for Bluetooth calls.
15. Disc slot: Internal microphone for Bluetooth calls.
DOP User manual_ENG.indd 5 14/11/2013 12:05:04

- 6 -
Front Panel
M-OF7050 Product overview
Notice:
The graphic in this manual is for reference only, and may be different from the actual unit.
1
11
10
9
2
3
4
56
7
8
12
13
14
1. [VOL/ / ] Knob
Press to turn the unit ON. Press and hold to turn the unit OFF.
Rotate to adjust the volume. Press momentarily to activate the MUTE function. Press again to
resume normal listening.
Press the [ ] key rotate the knob adjust the screen brightness
2. [MENU] Button: Press to switch between the available audio/video sources applied to the unit.
3. Navigation: Press to switch to navigation mode.
4. Reset Button: Press to reset system settings to factory default (except password and parental
lock settings).
5. USB port:Connect a USB device for playback of music/video files.
6. SD/SDHC card slot: Insert an SD card for playback of music/video/picture files.
7. Map Slot: The SD card is used for the Navigation Map only, not for music or other files.
8. [ ] Button: Adjust screen brightness (press) Black screen (long press).
9. [FM/AM] Button: Press to enter the radio Mode. Press to switch radio band.
10. [ TUNE / SELECT/ ] knob:
Rotate to select next/previous track or preset station.
Play/pause(press). Enter EQ setting(long press).
11. [ ] Button: Press to eject a disc.
12. Disc slot: Internal microphone for Bluetooth calls.
13. [BT] Button: Enter the Bluetooth Mode.
14. Internal Microphone: Internal microphone for Bluetooth calls.
DOP User manual_ENG.indd 6 14/11/2013 12:05:06

- 7 -
Front view
Remote control overview
EJECT
1. Change Current Source.
2. Eject the disc.
3. Enter the DVD menu.
4. Enter the DVD Title.
5. Zoom in /out on an image.
6. Select radio band.
7. EQ setting
8. Dimmer adjustment
9. [ ]- Fast Reverse
[ ]- Fast Forward
10. Dial/Receive call
11. Confirm
12. [ ]-Play Photo:UP-DOWN Mirror;
Play Disc:Select Files.
[ ]-Play Photo:Left-Right Mirror;
Play Disc:Select Files.
[ ]-Return To Play List
[ ]-Play Photo:Clockwise Rotation ;
Play Disc:Select Files.
13. Stop/Return
14. Digit area
15. Press to switch between the main menu and
current source
16. Power on/off
17. Photo Angle Select
18. DVD Subtitle
19. Setup to repeat playback from time frame A to
time frame B.
20. Repeat playback of current chapter.
21. Slow playback
22. Play all chapter in random order.
23. - Radio tune
[ ]- Previous
[ ]- Next
24. Hang up
25. Increase/Decrease volume.
26. Pause playback/Start playback.
27.Mute on/ off audio output
28. Audio Channel Select.
DOP User manual_ENG.indd 7 14/11/2013 12:05:06

- 8 -
Back view
Remote control overview
PULL OUT PUSH IN
Notes on Remote Control Usage
1. Aim the remote control at the remote sensor on the unit.
2. Replace the battery from the remote control or insert a battery insulator if the battery has not
been used for a month or longer.
3. DO NOT store the remote control in direct sunlight or in a high temperature environment, as it
may not function properly.
4. The battery can last up to for 6 months in normal conditions. If the remote control does not
work, please change the battery.
5. Use“button shaped” lithium battery“CR2025”(3V) only.
6. DO NOT recharge, disassemble, heat or expose the battery to fire.
7. Insert the battery in the proper direction according to the ( + ) and ( - ) poles.
8. Store the battery in a place where it cannot be reached by children to avoid the risk of accident.
Controls
The touch key areas for DVD playback are outlined below:
A: Return to the main menu
B: Play the video and display playback information
C: Display onscreen control menu
D: Time display
B
C
A
Touch screen
DOP User manual_ENG.indd 8 14/11/2013 12:05:07

- 9 -
Detect parking brake
• Connect the cable "BRAKE" to the parking brake switch to view video files on the TFT monitor.
Engage the parking brake for viewing videos.
• When the parking brake is not engaged, the monitor displays "Warning!!!, Video playback is
disabled for your safety. Engage parking brake to watch video.", preventing the driver to watch
content while driving. The rear screens are not interested in this inhibition.
Mute
Press [ VOL/ / ] knob to mute the volume from the unit. Press again to restore the volume.
[ ] is displayed on the LCD. Adjusting the volume or using any of the audio setup features
cancels the mute function.
Power On / Off
Press the [ VOL/ / ] knob on the unit to turn the unit on. The buttons on the front of the unit
light up for a moment and the current mode status appears in the LCD.
Press and hold the [ VOL/ / ] knob to power off the unit.
Audible Beep confirmation
An audible beep tone confirms each function selection. The Beep tone can be disabled through the
Setup menu.
Playing source selection
Press the [ MENU ] button on the front panel to change between available playing sources.
The playing mode is displayed on the screen.
1. Date and Time display. Double click to switch to Clock mode.
2. Function icons
3. or : Touch this page button to view the first or second page of on-screen buttons.
You also can drag left or right on the blank area to switch the pages.
4. Touch repeatedly to change wall papers.
5. Touch for quick access to Equalizer level settings.
Basic Operations
1
43 5 3
2
3
DOP User manual_ENG.indd 9 14/11/2013 12:05:07

- 10 -
Basic Operations
EQ menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical
characteristics of your vehicle, which vary depending on the type of vehicle and its measurements.
Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.
Notes:
1. The parameters of the EQ modes has been preset and you can not change them besides ‘User’.
2. The EQ mode will change to ‘User’ automatically when you adjust the frequency value under the
modes besides ‘User’.
3. The value of Sub is independent of EQ mode and can be adjusted separately.
Select preset equalizer
1. Enter the EQ setup mode
Touch the [ ] icon in the user interface and the EQ setup interface will display on the screen.
2. Select EQ mode
[User] [Rock] [Flat] [Class] [Pop] [Jazz] [Techno] [Optimal]
Adjust Fader/Balance
You can adjust front/back/left/right balance of the speaker and the subwoofer volume to get
balanced listening effect according to the surroundings and your interest.
Adjust EQ parameters
To adjust EQ parameters, touch and drag the parameters
adjustment bar.
Touch [ ] / [ ] or drag [ ] to adjust the
parameters.
• [ User ]: Set the desired audio effect.
• [BAS] bass range: -7 to +7
• [MID] middle range: -7 to +7
• [TRE] treble range: -7 to +7
• [LPH] low pass filter range: 60, 80, 100, 200
1. Enter the EQ setup mode
Touch the [ ] icon in the user interface and the EQ
setup interface will display on the screen.
2. Adjust subwoofer volume
Touch [ ] / [ ] or drag [ ] to adjust subwoofer
volume from 0 to38.
3. Adjust fader / balance value
Touch [ ] / [ ] / [ ] / [ ] to adjust fader /
balance value
[ ]: Front speaker, fader range: 0 to 7.
[ ]: Rear speaker, fader range: 0 to 7.
[ ]: Left speaker, balance range: 0 to 7.
[ ]: Right speaker, balance range: 0 to 7.
• [MPF] middle pass filter range: 0.5K, 1K, 1.5K, 2.5K
• [HPF] high pass filter rang: 10K, 12.5K, 15K, 17.5K
• [ LOUD: On/Off ]: When listening to music at low volumes, this featurewill selectively boost
certain bass and treble frequencies.
• [ RESET ]: Cancel the equalizer function settings.
DOP User manual_ENG.indd 10 14/11/2013 12:05:08

- 11 -
Setting Date /Time
Date /Time
1. Touch [ ].
2. Touch [ Time ].
The date/time setup menu is displayed.
Date
1. Touch [ Date ].
2. Touch the date information on the screen .
A submenu is displayed.
3. Touch [ ] or [ ] to set year, month and day.
Clock mode
1. Touch [Clock mode].
2. Touch [12H] or [24H] to switch clock mode.
Time
1. Touch [ Time ].
2. Touch the time on the screen, a submenu is displayed.
3. Touch [ ] or [ ] to set hour and minute.
Desk timer
1. Touch [ Desk Timer ].
2. Touch [ Simulate Timer ] or [ Numeral Timer ] .
Power off timer
1. Touch [ Power Off Timer ].
2. Touch [ On ] or [ Off ] to select whether timer displays after power off.
DOP User manual_ENG.indd 11 14/11/2013 12:05:08

- 12 -
Select radio as playing source
Open the Source Menu and then touch [Radio].
Select one radio Band
Touch the [ ] icon on the user interface to select one radio band among FM1, FM2, FM3, AM1 and
AM2.
Tune the radio
Auto Tuning
Press the [ ] / [ ] button on the remote control briefly or hold [ ] / [ ] icon on the user
interface more than 1 second to seek a higher / lower station.
To stop searching, repeat the operation above or press other keys having radio functions.
Manual Tuning
Method 1:
During manual tuning, the frequency will be changed in steps.
Press the [ ] / [ ] button on remote control or touch the [ ] / [ ] icon on the user interface
to tune in a higher / lower station.
Method 2:
1. Touch the numeric keypad icon [ ].
Numeric keyboard is displayed, touch number to
input frequency.
2. Touch [ ] to delete the input number step by step.
3. Touch [ OK ] to enter.
Radio Mode
1. Touch to view the SOURCE MENU and select a
new playback source
2. AF: Alternative Frequency indicator
3. TA: Traffic Announcement indicator
4. Distant signal broadcasting indicator
5. Current radio band indicator
6. Clock
7. Broadcaster information stored at the preset
8. Touch to view more on-screen buttons
9. Touch to seek backward
10. Scan preset stations
11. Touch to seek forward
12. Touch to change between AM/FM bands
13. Current radio information
14. RDS setting options
15. Current band preset radio stations
16. Touch to change between Local and Distance
17. Enter frequency directly
18. Touch for quick access to Equalizer level
settings
Tuner TFT display 1234
13
7
8
9 10 11 12
TA
14 15 16 17 18
56
AF
DOP User manual_ENG.indd 12 14/11/2013 12:05:09

- 13 -
Local seeking
Touch the [ ] icon and choose the Radio Local or Distance.
When the [ ] icon turns bright, only stations with a strong signal strength will be detected .
Default is “Distance”.
RDS basics
RDS transmits data to the radio which displays information such as name station, song artist, and
song title.
RDS service availability varies with areas.
Adjust RDS settings
1. In Radio menu, touch [ ].
The option menu is displayed.
2. Touch on the selected option to change the setting.
• [TA]: To turn on or off “TA” function.
• [AF]: To turn on or off “AF” function.
• [PTY]: To show PTY list.
Radio Mode
Preset station
The unit has 5 bands, such as FM1, FM2, FM3, AM1, AM2, and each band can store 6 stations; the
unit can store 30 stations in total.
Intro/Scan
Press the [ ] icon to intro. Each stored station will play
for 5 seconds automatically.
Hold down the [ ] icon to scan. Only stations with
sufficient signal strength will be detected and stored in the
memory. After scaning, P1 will play automatically.
Manual Store
1. Tune to a station.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ].
4. Touch one of the channels P1 to P6 to save the selected band.
Tune to a Preset Station
1. Touch [Radio].
2. Select a band (if needed).
3. Touch one of the preset channels (P1 to P6) on the screen.
DOP User manual_ENG.indd 13 14/11/2013 12:05:10

- 14 -
RDS ( Radio Data System )
The unit provides basic functions of RDS.
RDS service availability varies with areas. Please verify if RDS service is available in your area.
AF function
Alternative Frequencies Lists are used in conjunction with the PI code (Program Identification
code)to assist automatic tuning.
Using this information, the radio can automatically search out another frequency of the same
station.
Note:
• During auto switching radio frequency, some interference may be heard..
• Turning off AF function can settle this problem.
EON ( Enhanced Other Networks )
When EON data is received, the EON indicator lights and the TA and AF functions are enhanced.
TA: Traffic information can be received from the current station or stations in other network.
AF: The frequency list of preset RDS stations is updated by EON data. EON enables the radio to
make fuller use of RDS information. It constantly updates the AF list of preset stations, including
the one that currently tuned into.
TA function
The TA (Traffic Announcement) function lets the unit receive traffic announcements automatically.
The TA function can be activated by a TP (Traffic Program) station broadcasting traffic information.
When TA is activated and a traffic announcement is received, the current playing source will be
overridden by the traffic announcement The unit returns to the original source after the traffic
announcement has been received.
PTY function
PTY is an abbreviation for the type of program defined by a code to define the program being
broadcast (eg news or Rock).
The Options of PTY is displayed on the screen. To see the options PTY, tap the scroll bar and arrows
on the screen.
When an option is selected PTY (eg News), the radio unit, the PTY search available. If the PTY
requested was not found, the unit returns to the original radio frequency.
Radio Mode
DOP User manual_ENG.indd 14 14/11/2013 12:05:10

- 15 -
Load a disc
You can play video, audio or images stored on the following discs:
• DVD Video, DVD-R, DVD-RW
• VCD
• Audio CD, CD-R, CD-RW
Note:
Ensure that the disc contains playable content.
Eject a disc
Press the [ ] key on the front panel to eject the disc. When the disc is ejected, the unit switches to
the previous source.
Controlling playback
To access the on-screen controls, touch the screen except upper left corner, and touch again to
cancel display. Touch [ ] to view all function icons.
Connect a USB device
1. Open the USB door.
2. Insert the small end of the USB cable to mini USB socket, then connect the other end of the
cable to your USB device.
Remove a USB device
1. Select other source on the main menu.
2. Remove the USB device.
Insert a SD/MMC card (only for M-OF7040 and M-OF7050)
1. Open SD/MMC card cover.
2. Insert the SD/MMC card into the SD/MMC card slot.
Play starts automatically.
Remove a SD/MMC card (only for M-OF7040 and M-OF7050)
1. Select other source on the main menu.
2. Press the SD card to remove it.
Play/Pause
1. Once a disc, USB or SD/MMC card is inserted, play starts automatically.
For DVD movie, if a menu appears, press [ ] to start play.
2. To pause, touch [ ].
To resume play, touch [ ].
3. Skip to previous / next track / chapter, press [ ] / [ ] key.
Previous/Next
Touch [ ] / [ ] key on the screen to skip to previous / next track / chapter.
Playback Mode
DOP User manual_ENG.indd 15 14/11/2013 12:05:10

- 16 -
Search for a folder
For Audio Files
1. Touch [ ] to display all available audio folders.
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Video Files
1. Touch [ ] to display all available video folders.
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Picture Files
1. Touch [ ] to display all available picture folders
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play.
For Folder Control
1. Touch [ ] to display all available folders
2. Touch a folder,then touch the desired file.
3. Touch the file again to start play
Repeat
For DVD/VCD movie disc:
1. Touch bottom half of the screen to display menu on the
screen.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to select:
DVD
[ ] Repeat chapter: Play the current chapter
repeatedly.
[ ] Repeat title: Play all chapters in the title repeatedly.
[ ] Repeat off: Play all in the all repeatedly.
[ ] Repeat off: Cancel repeat play.
VCD
[ 1 ] Repeat single: Play the current single repeatedly.
[ ] Repeat all: Play all in the all repeatedly.
[ ] Repeat off: cancel repeat play.
Playback Mode
DOP User manual_ENG.indd 16 14/11/2013 12:05:10

- 17 -
For CD/MP3/WMA files:
1. Touch anywhere except the upper left corner to display menu on the screen.
2. Touch [ ] repeatedly:
[ 1 ] Repeat single: Play the current single repeatedly.
[ ] Repeat all: Play all in the all repeatedly.
[ ] Repeat off: Cancel repeat play.
Repeat A-B
You can repeat a specific of video file (from A to B).
1. Touch the screen to display control menu, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ A-B ] repeatedly to mark:
Repeat A-: the start of the section to repeat.
Repeat A-B: the end of the section to repeat.
The selected section plays repeatedly.
4. To exit A-B repeat mode, touch A-B repeatedly, [Repeat A-B off] is displayed.
Shuffle (Random) play
You can play audio tracks/files in random order.
1. Touch the screen to display control menu, if necessary.
2. Touch [ ] to display the 2nd menu, if necessary.
3. Touch [ ] on the screen repeatedly to turn random play on or off.
Select audio mode
When you play VCDs, you can select an audio mode (R/L/Stereo).
1. During play, touch bottom half of the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
Touch [ ] repeatedly until the audio mode is selected.
Select subtitle language
For DVD or Divx discs that contain two or more subtitle languages.
1. During play, touch the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to select a language.
The selected language is displayed.
Change viewing angle
Some DVDs contain alternate scenes, such as scenes recorded from different camera angles.
For these DVD disc, you can select from the available alternate scenes.
Press [ Angle ] repeatedly on the remote control., the viewing angle is changed.
Playback Mode
DOP User manual_ENG.indd 17 14/11/2013 12:05:11

- 18 -
Direct track entry
To select a track directly, touch the [ ] icon on screen control
to display the direct entry menu. Enter the desired track using the
on-screen number pad. Press [ OK ] to the selected track.
Playback information
Touch the screen when playing back DVD and VCD discs and the playback information will be
displayed on the top area of the TFT.
Playback Mode
For DVD
1. Disc type.
2. DVD Title information. “01/08” indicates that this DVD has
8 titles and the title playing back now is the first title.
3. DVD Chapter information. “005/012” indicates that current
title has 12 chapters and the chapter playing back now is
the fifth chapter.
For VCD
1. Disc type.
2. VCD Track information. “01/08” indicates that this VCD
has 8 tracks and the track playing back now is the first
track.
Elapsed Time
1. Elapsed time of the current track.
2. Total time of the current track.
DVD T:01/08 C:005/012
123
VCD Track:01/08
12
00:01:20 00:30:17
12
Rotate pictures
1. When you view pictures, touch the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to rotate the picture.
Zoom
You can zoom in pictures for a close view.
1. When you view pictures, touch the screen to display menu on the screen, if necessary.
2. Touch [ ] to display the 2nd menu.
3. Touch [ ] repeatedly to zoom in the picture.
Video setup
Touch [ ] to access video setup mode, touch [ ] or [ ] to
set the desired effect.
You may set the brightness, contrast, saturation, and hue of the
video output from 1 to 20.
DOP User manual_ENG.indd 18 14/11/2013 12:05:11

- 19 -
You can make or receive phone calls with Bluetooth-enabled phones through the unit. You can also
listen to music from a Bluetooth-enabled device.
Bluetooth Mode
xxxxx
Pair the Bluetooth-enabled devices
To connect your Bluetooth device to the unit, you need to
pair the device to the unit. Pairing needs only to be done
once. You can pair up to five devices.
1. Turn on the Bluetooth function on the device.
2. Touch [ ] to search for Bluetooth device with the unit.
3. Start scanning on the Bluetooth device and select the
unit “XXXXX”
4. Enter default password “0000”.
Tip:
• The operational range between this unit and a Bluetooth device is approximately 5 meters .
• Before you connect a Bluetooth device to this unit, familiarize yourself with the Bluetooth
capabilities of the device.
• Compatibility with all Bluetooth device is not guaranteed.
• Any obstacle between this unit and a Bluetooth device can reduce the operational range.
• Keep this unit away from any other electronic device that may cause interference.
Disconnect Bluetooth device
To disconnect one device, touch [ ] .
Tip
• The device will also be disconnected when the device is moved beyond the operational range.
• If you want to reconnect the device to the unit, place it within the operational range.
• If you do not want to reconnect the device to the unit automatically, touch [ ],
then set [ Auto connect ] to [ Off ]. For details, see the “Adjust Bluetooth Settings” section.
Make a call
1. Select Bluetooth function in the home menu.
2. Pair the phone with the unit.
3. Search for phone number from the following list:
[Phone Book]
[Call Log]
[Missed calls]
[Received calls]
[Dialed calls]
Or touch the number pad directly, then touch [ ] to dial.
xxxxx
DOP User manual_ENG.indd 19 14/11/2013 12:05:12