Magnavox MME-110 User manual

1
8240 009 34241
SMART. VERY SMART.
User guide
MICRO HI-FI STEREO SYSTEM
Read this manual first!
Congratulations on purchasing this Magnavox product.
We’ve included everything you need to get started.
If you have any problems, Magnavox Representatives can
help you get the most from your new product by explaining:
• Hookups,
• First Time Setup, and
• Feature Operation.
Do not attempt to return this product to the store.
For fast help, call us first!
1-800-705-2000
Thank you for making Magnavox a part of your home!
S
E
E
W
H
Y
I
N
S
I
D
E
I
M
P
O
R
T
A
N
T
!
Return
your Warranty
Registration Card
within 10 days
MME-110
pg 001-024/MME110/37-Eng 6/3/02, 12:47 PM1

2
8240 009 34241
Canada
English:
This digital apparatus does not exceed
the Class B limits for radio noise
emissions from digital apparatus as set
out in the Radio Interference
Regulations of the Canadian
Department of Communications.
Français:
Cet appareil numérique n'emet pas
de bruits radioélectriques dépassant
les limites applicables aux appareils
numériques de Class B prescrites dans
le Règlement sur le Brouillage
Radioélectrique édicté par le Ministère
des Communications du Canada.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
CAUTION
:INVISIBLE
LASER RADIATION
WHEN OPEN. DO NOT STARE INTO BEAM.
DANGER
:
INVISIBLE LASER RADIATIONWHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINANAKYMATTOMAALLE LASERSATEILYLLE. ALA
KATSO SATEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD.
OCH SPARREN AR URKOPPLAD. BETRAKTA EJ STRÅLEN.
DANGER - Invisible laser radiation when open.
AVOID DIRECT EXPOSURE TO BEAM.
or
This warning label is located on the rearside
and inside this laser product.
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM2

3
8240 009 34241
3
MME-110 MICRO HIFI STEREO SYSTEM
STANDBY-ON
TAPE
DYNAMIC BASS BOOST
CD
TUNER AUX PROGRAM
REPEAT/
SLEEP
DSC
PLAY•PAUSE
VOLUME
FULL AUTO STOP
DBB
DIGITAL
SOUND
CONTROL
1
2
7
8
6
3
4
5
!
9
0
5
@
^
&
(
*
3
4
9
0
)
¡
™
!
£
2
≤
CD / CD-R/CD-RW COMPATIBLE
OPEN/
CLOSE
%
#
$
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM3

4
8240 009 34241
• Once your Magnavox purchase is
registered, you’re eligible to receive all
the privileges of owning a Magnavox
product.
• So complete and return the Warranty
Registration Card enclosed with your
purchase at once, and take advantage
of these important benefits.
Return your Warranty Registration card today to
ensure you receive all the benefits you’re entitled to.
Warranty
Verification
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Magnavox warranty.
Owner
Confirmation
Your completed Warranty
Registration Card serves
as verification of owner-
ship in the event of prod-
uct theft or loss.
Model
Registration
Returning your Warranty
Registration Card right
away guarantees you’ll
receive all the information
and special offers which
you qualify for as the
owner of your model.
t
This “bolt of lightning” indi-
cates uninsulated material
within your unit may cause
an electrical shock. For the safety of
everyone in your household, please do
not remove product covering.
s
The “exclamation point” calls
attention to features for
which you should read the
enclosed literature closely to prevent
operating and maintenance problems.
WARNING: TO PREVENT
FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
CAUTION: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
For Customer Use
Enter below the Serial No. which is locat-
ed on the rear of the cabinet. Retain this
information for future reference.
Model No. _______________________
Serial No. ________________________
MAC5097
Know these
ssaaffeettyysymbols
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM4

5
8240 009 34241
Congratulations on your purchase,
and welcome to the “family!”
Dear Magnavox product owner:
Thank you for your confidence in Magnavox.You’ve selected one of the
best-built, best-backed products available today.And we’ll do everything in
our power to keep you happy with your purchase for many years to come.
As a member of the Magnavox “family,” you’re entitled to protection by
one of the most comprehensive warranties and outstanding service net-
works in the industry.
What’s more, your purchase guarantees you’ll receive all the information
and special offers for which you qualify, plus easy access to accessories
from our convenient home shopping network.
And most importantly you can count on our uncompromising commitment
to your total satisfaction.
All of this is our way of saying welcome – and thanks for investing in a
Magnavox product.
Sincerely,
Lawrence J. Blanford
President and Chief Executive Officer
P.S. Remember, to get the most from your Magnavox product,
you must return your Warranty Registration Card within
10 days. So please mail it to us right now!
R
E
G
I
S
T
R
A
T
I
O
N
N
E
E
D
E
D
W
I
T
H
I
N
1
0
D
A
Y
S
Hurry!
Visit our World Wide Web Site at http://www.magnavox.com
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM5

6
8240 009 34241
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. Clean only with a dry cloth.
7. Do not block any ventilation
openings. Install in accordance with
the manufacturer´s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the
safety purpose of the
polarized or
grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong.The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10.
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
15.
Battery usage CAUTION –To
prevent battery leakage which may result in
bodily injury or damage to the unit:
● Install all batteries correctly, +and -as
marked on the unit.
● Do not mix batteries (old and new or
carbon and alkaline, etc.).
● Remove batteries when the unit will not be
used for a long time.
EL 6475-E003: 01/6
IMPORTANT SAFETY INSTRUCTIONS
AC Polarized
Plug
Class II equipment symbol
This symbol indicates that the unit has
a double insulation system
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM6

7
English
Español
8240 009 34241
English ------------------------------------------------ 8
Español --------------------------------------------- 28
Index
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM7

8
English
8240 009 34241
Contents
General Information
Supplied accessories ............................................ 9
Environmental information ................................ 9
Safety information ................................................ 9
Preparations
Rear connections ........................................ 10–11
Power
Antennas connection
Speakers connection
Optional connection ......................................... 11
Connecting other equipment to your system
Inserting batteries into the remote control . 11
Controls
Controls on the system and remote
control .................................................................. 12
Basic Functions
Switching the system on ................................... 13
Switching the system to standby mode ........ 13
Volume control ................................................... 13
Sound control ..................................................... 13
CD Operations
Discs for playback .............................................. 14
Playing a disc ........................................................ 14
Selecting a different track ................................. 14
Finding a passage within a track ...................... 14
Different play modes: SHUFFLE
and REPEAT ......................................................... 15
Programming the disc tracks ........................... 15
Reviewing the program ..................................... 15
Erasing the program .......................................... 15
Radio Reception
Tuning to radio stations .................................... 16
Programming radio stations ............................. 16
Manual programming
Tuning to preset radio stations ....................... 16
Tape Operation/Recording
Tape playback ...................................................... 17
General information on recording ................. 17
Preparation for recording ................................ 17
Synchro start CD recording ............................ 18
One touch recording......................................... 18
Clock/Timer
Clock setting ....................................................... 19
Timer setting ....................................................... 19
Sleep timer setting ............................................. 20
Specifications ........................................... 21
Maintenance.............................................. 22
Troubleshooting ............................. 22–23
Limited Warranty ................................ 24
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM8

9
English
8240 009 34241
General Information
This system complies with the FCC rules,
Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two
conditions:
– This device may not cause harmful
interference, and
– This device must accept any interference
received, including interference that may
cause undesired operation.
Supplied accessories
– 2 speaker boxes
– remote control
– AM loop antenna
– FM wire antenna
Environmental Information
All unnecessary packaging has been omitted.We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Safety information
●Place the system on a flat, hard and stable
surface.
●Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
●Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
●The lens may cloud over when the system is
suddenly moved from cold to warm
surroundings, making it impossible to play a disc.
Leave the system in the warm environment until
the moisture evaporates.
●The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
●When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM9

10
English
8240 009 34241
Preparations
AM
aerial
AUX in
RIGHT LEFT
LR
speaker
(right) speaker
(left)
A
B
C
AC power cord
FM wire antenna
AM loop
antenna
3
FM
aerial
300
Rear connections
The type plate is located at the rear of the
system.
APower
Before connecting the AC power cord to the
wall outlet, ensure that all other connections
have been made.
WARNING!
– For optimal performance, use only the
original power cable.
– Never make or change connections with
the power switched on.
To avoid overheating of the system, a safety
circuit has been built in. Therefore, your
system may switch to Standby mode
automatically under extreme conditions. If
this happens, let the system cool down
before reusing it (not available for all versions).
BAntennas Connection
Connect the supplied AM loop antenna and FM
antenna to the respective terminals. Adjust the
position of the antenna for optimal reception.
AM Antenna
●Position the antenna as far as possible from a TV,
VCR or other radiation source.
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM10

11
English
8240 009 34241
Preparations
FM Antenna
1
2
●For better FM stereo reception, connect an
outdoor FM antenna to the FM AERIAL (FM
ANTENNA) terminal.
CSpeakers Connection
Front Speakers
Connect the speaker wires to the SPEAKERS
terminals, right speaker to "RIGHT" and left
speaker to "LEFT", colored (marked) wire to
"+" and black (unmarked) wire to "-".
12
●Fully insert the stripped portion of the speaker
wire into the terminal as shown.
Notes:
–For optimal sound performance, use the
supplied speakers.
–Do not connect more than one speaker to any
one pair of + / - speaker terminals.
–Do not connect speakers with an impedance
lower than the speakers supplied. Please refer to
the SPECIFICATIONS section of this manual.
Optional connection
The optional equipment and connecting cords
are not supplied. Refer to the operating
instructions of the connected equipment for
details.
Connecting other equipment to your
system
Connect the audio left and right OUT terminals
of a TV,VCR, Laser Disc player, DVD player or
CD Recorder to the AUX IN terminals.
Note:
–If you are connecting equipment with a
monaural output (a single audio out terminal),
connect it to the AUX IN left terminal. Alternatively,
you can use a “single to double”cinch cable, but
the output sound still remain monaural.
Inserting batteries into the
remote control
Insert two batteries (not supplied) type R03 or
AAA into the remote control with the correct
polarity as indicated by the "+" and "-"
symbols inside the battery compartment.
CAUTION!
– Remove batteries if they are exhausted
or will not be used for a long time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances, so
they should be disposed off properly.
pg 001-024/MME110/37-Eng 6/3/02, 12:48 PM11

12
English
8240 009 34241
Controls (illustrations on page 3)
Controls on the system and
remote control
1STANDBY ON y
– to switch the system on or to standby mode.
2SOURCE
– to select the respective sound source : CD,
TUNER, TAPE or AUX.
3PROGRAM /9
for CD ................. press to stop playback or to
clear a program.
for CD/Tuner ... to enter programming mode.
4PLAY•PAUSEÉÅ
for CD ................. to start or interrupt playback.
5S T
for CD ................. press to select a desired track.
................................. press and hold to fast reverse/
forward the disc.
forTuner ............. press to tune to a lower or
higher radio frequency.
6REPEAT / SLEEP
for CD ................. to repeat a track/ entire CD.
forTimer ............. to activate/deactivate or set the
sleep timer.
7Tape deck
8Tape Deck Operation
â.......................... to start recording.
É.......................... to start playback.
à/ á............... to rewind or fast forward.
70 ........................ to stop playback/recording or to
open the tape door.
Å.......................... to interrupt playback or
recording.
9DSC (DIGITAL SOUND CONTROL)
– to select the desired sound effect : OF (flat),
RO (rock), PO (pop) or JA (jazz).
0DBB (DYNAMIC BASS BOOST)
– to enhance the bass
!VOLUME (VOL +/-)
– to increase or decrease the volume.
@Display screen
– to view the current status of the system.
#n
– connect headphones.
$Disc tray
%OPEN/CLOSE ç
– to open or close the disc tray.
^BAND
forTuner ............. to select waveband : FM or AM.
&REPEAT
– to repeat a track / entire disc.
*SHUFFLE
– to play CD tracks in random order.
(¡/ ™
for CD ................. to select a desired track.
forTuner ............. to select a preset radio station.
)MUTE
– interrupts and resumes sound reproduction.
¡à/ á
for CD ................. press and hold to fast reverse/
forward the disc.
forTuner ............. press to tune to a lower or
higher radio frequency.
for Clock ............ to set the hours and minutes.
™TIMER
– to activate the timer/clock function.
£SLEEP
– press and hold to set sleeping time.
≤B
– to switch the system on or to standby mode.
Notes for remote control:
– While the system is in active mode,
select the source you wish to control by
pressing SOURCE key on the remote
control.
– Then select the desired function (for
example É , í , ë ).
pg 001-024/MME110/37-Eng 6/3/02, 12:49 PM12

13
English
8240 009 34241
Basic Functions
STANDBY-ON
TAPE
DYNAMIC BASS BOOST
CD
TUNER AUX PROGRAM
REPEAT/
SLEEP DSC
PLAY•PAUSE
VOLUME
DBB
DIGITAL
SOUND
CONTROL
IMPORTANT!
Before you operate the system, complete
the preparation procedures.
Switching the system on
●Press STANDBY ON 2.
➜The system will switch to the last selected
source.
●Press CD/ TUNER/ TAPE/ AUX (or
SOURCE on remote control).
➜The system will switch to the selected source.
Switching the system to standby
mode
●Press STANDBY ON 2on the system or
remote control.
●If in tape mode or recording mode, press 70
first.
➜The volume level, interactive sound settings,
last selected source and tuner presets will be
retained in the player's memory.
Volume control
Press 34 on the system to increase or decrease
the volume (or press VOL -/+on the
remote control).
➜Display shows the volume level number from
0-MAX.
To switch off the volume temporarily
●Press MUTE on the remote control.
➜Playback will continue without sound and
"MU" is displayed.
●To restore the volume, press MUTE again or
decrease/increase the volume level.
Sound control
●Press DSC repeatedly to select the desired
sound effect : OF (flat), RO (rock), PO (pop) or
JA (jazz).
●Press DBB to switch on or off the bass
enhancement.
➜If the DBB is activated, DBB is shown.
pg 001-024/MME110/37-Eng 6/3/02, 12:49 PM13

14
English
8240 009 34241
CD Operations
STANDBY-ON
TAPE
DYNAMIC BASS BOOST
CD
TUNER AUX PROGRAM
REPEAT/
SLEEP DSC
PLAY•PAUSE
VOLUME
DBB
DIGITAL
SOUND
CONTROL
IMPORTANT!
The lens of the CD player should never be
touched.
X
Discs for playback
This system is able to play:
– All pre-recorded audio CDs
– All finalized audio CDR and audio
CDRW discs
●CD-ROM, CD-I, CDV, VCD, DVD or computer
CDs are not possible for playback purposes with
the Micro Hi-Fi.
Playing a disc
1Select CD source.
2Press OPEN/CLOSEçon the top of the
system to open the CD compartment.
➜“OPEN” is displayed.
3Insert a disc with the printed side facing up and
press OPEN/CLOSEçto close the CD door.
➜“cd---” is displayed as the CD player scans
the contents of a disc, and then the total number
of tracks and playing time are shown.
4Press ÉÅ to start playback.
To interrupt playback
●Press ÉÅ.
➜The current track time flashes.
●To resume playback, press ÉÅ again.
To stop playback
●Press Ç.
Note:
–Disc play will also stop when you select another
source or the disc has reached the end.
Selecting a different track
●Press Sor T (¡or ™) briefly and
repeatedly until the desired track number
appears in the display.
●If playback is stopped, pressÉÅ to start
playback.
Finding a passage within a track
1Press and hold down on Sor T (àor
á).
➜The disc is played at high speed and low
volume.
2When you recognize the passage you want,
release Sor T (àor á).
➜Normal playback continues.
Note:
–During a disc program or if REPEAT/SHUFFLE
mode active, searching is only possible within the
same track.
pg 001-024/MME110/37-Eng 6/3/02, 12:49 PM14

15
English
8240 009 34241
CD Operations
Different play modes: SHUFFLE
and REPEAT
You can select and change the various play
modes before or during playback.
1Press REPEAT or SHUFFLE on the remote
control to select :
➜SHUFFLE – tracks of the entire disc played in
random order.
➜(REPEAT ALL) – to repeat the entire
disc/ program.
➜1(REPEAT) – to repeat the current
track.
2To return to normal playback, press REPEAT or
SHUFFLE until the various REPEAT/ SHUFFLE
modes are no longer displayed.
●You can also press 9to cancel your play mode.
Programming the disc tracks
Programming tracks is possible when playback is
stopped. Up to 30 tracks can be stored in the
memory in any order.
1Press PROGRAM to enter the programming
mode.
➜A track number is shown and PROG flashes.
2Press Sor T (¡or ™) repeatedly to
select your desired track number.
3Press PROGRAM to confirm the track number
to be stored.
➜The last programmed tracks, the number of
tracks programmed and “PROG” will be
displayed.
4Repeat steps 2-3 to select and store all desired
tracks.
➜“FULL” is displayed if you attempt to
program more than 30 tracks.
5To start playback of your disc program, press ÉÅ.
Note:
–During programming, if no button is pressed
within 15 seconds, the system will exit the program
mode automatically.
Reviewing the program
In stop mode, press Sor T (àor á)
until the display shows all your stored track
numbers in sequence.
Erasing the program
●Press and hold Çwhen playback is stopped.
➜PROG disappears from the display.
Note:
–The program will be erased when the system is
disconnected from the power supply or when the
disc tray is opened.
pg 001-024/MME110/37-Eng 6/3/02, 12:49 PM15

16
English
8240 009 34241
Radio Reception
STANDBY-ON
TAPE
DYNAMIC BASS BOOST
CD
TUNER AUX PROGRAM
REPEAT/
SLEEP DSC
PLAY•PAUSE
VOLUME
DBB
DIGITAL
SOUND
CONTROL
Tuning to radio stations
1Select TUNER source.
2Press TUNER again (or BAND on the remote
control) to select the desired waveband : FM or
AM.
3Press and hold down on Sor T (àor
á) until the frequency indication starts to
change, then release.
➜The display will show "Src" until a radio
station with sufficient signal strength is found.
4Repeat step 3if necessary until you find the
desired station.
●To tune to a weak station, press Sor T
(àor á) briefly and repeatedly until you have
found optimal reception.
Programming radio stations
You can store up to a total of 15 radio stations
for both FM and AM bands in the memory.
Manual programming
1Tune to your desired station (refer to “Tuning to
radio stations”).
2Press PROGRAM to activate programming.
➜PROG flashes in the display.
3Press Sor T( ¡or ™) briefly and
repeatedly to assign a number from 1 to 15 to
this station.
4Press PROGRAM again to confirm the setting.
➜PROG disappears, the system will resume to
the last tuned radio station.
5Repeat the above four steps to store other
stations.
●You can override a preset station by storing
another frequency in its place.
Note:
–During programming, if no button is pressed
within 15 seconds, the system will exit the program
mode automatically.
Tuning to preset radio stations
●Press ¡or ™on the remote control briefly and
repeatedly until the desired preset station is
displayed.
pg 001-024/MME110/37-Eng 6/3/02, 12:50 PM16

17
English
8240 009 34241
Tape Operation / Recording
Tape playback
1Select TAPE source.
➜The display shows “TAPE” throughout tape
operation.
2Press 70 to open the tape door.
3Insert a recorded tape and close the tape door.
●Load the tape with the open side downward and
the full spool to the left.
4Press Éto start playback.
5To interrupt playback, press Å. To resume
playback, press this key again.
6By pressing àor áon the system, fast winding
of tape is possible in both directions.
7To stop the tape, press 70.
●The keys are automatically released at the end of
the tape, except if Åhas been activated.
General information on
recording
●For recording, use only NORMAL (IEC type I)
tapes on which the tabs have not yet been
broken.This deck is not suited for recording on
METAL (IEC IV) type tapes.
●The best recording level is set automatically.
Altering the VOLUME, DSC or DBB will not
affect the recording in progress.
●At the very beginning and end of the tape, no
recording will take place during the 7 seconds
when the leader tape passes the recorder heads.
●To protect a tape from accidental erasure, have
the tape in front of you and break out the left
tab. Recording on this side is no longer possible.
If, however, you wish to record over this side
again, cover the tabs with a piece of adhesive
tape.
IMPORTANT!
Recording is permissible if copyright or
other rights of third parties are not
infringed upon.
Preparation for recording
1Select TAPE source.
2Load a recordable tape into tape deck with full
spool to the left.
3Prepare the source to be recorded.
CD – load the disc.
TUNER – tune to the desired radio station.
AUX – connect external equipment.
When recording is in progress
●It is not possible to listen to another source.
●It is not possible to activate the timer function.
To stop recording
●Press 70.
To interrupt recording
●Press Å.
●To resume recording, press Åagain.
MME-110 MICRO HIFI STEREO SYSTEM
FULL AUTO STOP
pg 001-024/MME110/37-Eng 6/3/02, 12:50 PM17

18
English
8240 009 34241
Tape Operation / Recording
Synchro start CD recording
1Select CD source.
●Press Sor T (¡or ™) briefly and
repeatedly to select the desired track to start
recording.
●You can program the tracks in the order you
want them to be recorded (refer to “CD
Operation - Programming the disc tracks”).
2Press âto start recording.
➜Playing of the CD program starts
automatically from the beginning of the CD,
“5cd”,“4cd”... ”1cd” will be displayed before
recording starts. It is not necessary to start the
CD player separately.
One touch recording
1Select CD, TUNER or AUX source.
2If necessary, start playback of the selected
source.
3Press âto start recording.
pg 001-024/MME110/37-Eng 6/3/02, 12:50 PM18

19
English
8240 009 34241
Clock/Timer
STANDBY-ON
TAPE
DYNAMIC BASS BOOST
CD
TUNER AUX PROGRAM
REPEAT/
SLEEP DSC
PLAY•PAUSE
VOLUME
DBB
DIGITAL
SOUND
CONTROL
Clock setting
The clock can be set in 12-hour mode.
1Press TIMER on the remote control.
➜The hours indicator will start flashing.
2Press àor áon the remote control to set
the hours.
3Press PROGRAM to confirm.
➜The minutes indicator will start flashing.
4Press àor áon the remote control to set
the minutes.
5Press PROGRAM to store the setting.
➜The clock will start working.
Notes:
–The clock setting will be cancelled when the
power cord is disconnected or if a power failure
occurs.
–During clock setting, if no button is pressed
within 15 seconds, the system will exit clock setting
mode automatically.
Timer setting
The system can switch on to CD orTUNER
mode automatically at a preset time, serving as
an alarm to wake you up.
IMPORTANT!
– Before setting the timer, ensure that the
clock is set correctly.
– The timer can only be activated from
standby mode.
1Press and hold TIMER for more than two
seconds.
➜will appear on the display.
2Press PROGRAM to change the previous
setting or start a new setting.
➜“FM”,“AM” or “cd” will start flashing.
3If necessary, press àor áon the remote
control to select the desired source.
4Press PROGRAM to confirm.
●If “FM” or “AM” is selected, press àor áon
the remote control to select a desired preset
radio station.
5Press PROGRAM to confirm.
➜The volume level will be displayed.
6Press àor áon the remote control to set
the volume level.
7Press PROGRAM to confirm.
➜The hour indicator will start flashing.
8Press àor áon the remote control to set
the timer start hours and press PROGRAM to
store. Repeat the same procedures to set the
minutes.
➜will appear on the display.
9Switch the system to standby mode.
●When reached the preset time, the selected
sound source will play if the timer has been
activated.
Note:
–The timer setting will be cancelled when the
power cord is disconnected or if a power failure
occurs.
pg 001-024/MME110/37-Eng 6/3/02, 12:50 PM19

20
English
8240 009 34241
Sleep timer setting
The sleep timer enables the system to switch off
by itself after a set period of time.The clock time
needs to be set first before the sleep timer can
be used.
1Press SLEEP on the remote control repeatedly
to select a preset time.
➜The selections are as follows (time in
minutes):
OFF ™10 ™20 ™30 ™40 ™50 ™60 ™
70 ™80 ™90 ™OFF …
➜"XX" or "OFF" is displayed. "XX" is the time in
minutes.
2When you reach the desired length of time, stop
pressing the SLEEP button.
To deactivate the sleep timer
●Press SLEEP repeatedly until "OFF" is displayed,
or press the STANDBY ON button.
Clock/Timer
pg 001-024/MME110/37-Eng 6/3/02, 12:50 PM20