Magnavox MRU3500 - Universal Remote Control User manual

32
IntroductionTable of Contents
Introduction.................................................... 3
ButtonFunctions............................................. 4
SAT/DVDFunctions .................................. 6
TV/VCR/INPUT ....................................... 6
Setup............................................................. 7
BatteryInstallation...................................... 7
BatterySaver ............................................. 7
CodeSaver ............................................... 7
Power-Ondefault ...................................... 7
CodeSetup ............................................... 7
CodeEntry .................................................... 8
DirectCode Entry...................................... 8
CodeSearch ............................................. 8
BrandSearch............................................. 9
Code Identification Feature ........................... 10
Programming Combo Device Codes .............. 11
ControllingCombo Devices........................... 11
ControllingDevices withPower Onand Off.... 11
VCR/DVD/DVRPunch-Through Feature....... 12
Volume/MuteControl Feature........................ 12
SettingVolume/MuteControl,Punch-Through.13
Settingany Modeto useits ownVolume/Mute 13
Troubleshooting ............................................ 14
Instruccionesen Español ............................... 16
Manueld’instruction...................................... 30
Congratulations on your purchase of Magnavox
Universal Remote Control. Magnavox Universal
Remotes let you replace a broken or lost remote or
combine more than one remote into one. In addition, this
remote is equipped with a command learning feature
which lets the remote learn commands from your original
equipment remote control!
This remote control operates the common features of
most but not all models and brands of IR Infrared
ControlledVideoEquipment. This remotemayprovide
functions that are not available on your equipment.
Some functions of your particular equipment (e.g. menu
functions) may not be controlled by this remote. In such
cases, use the original remote control for your
equipment. Please use this manual to become familiar
with your Magnavox Universal Remote. After you are
familiar with your remote the first thing you need to do is
to install batteries and setup your remote for your
particular product and brand.
Thank you for buying a Magnavox remote and we hope
it will give you many years of service.
MRU3500-OM_H14102.pmd 9/6/2006, 4:07 PM2-3

54
Button Functions, cont.
Button Functions
Note: The REC button must be pressed TWICE to
record from your VCR. For some brands of VCRs, you
might need to press the REC button once, then press it
again for three seconds.
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling.E.G. PREV.CHAN maybecalled RECALL,or
ENTER may be called DISPLAY.Thesedifferences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product.E.G., your product must have PREV.CHAN
ability for thePREV.CHAN button to operate this
feature.
1. Red IndicatorLights when any button is pressed.
2. TV,VCR,DVD,CBL,SAT Selects product to be
operated.
3. CC(SUBTITLE)TVClosedCaption (ifyourTV has
this feature) or DVD Subtitle toggle.
4. CHANNELUP/DOWNChanges the channels.
5. NUMBERSEnter numbersfordirect channel
selection. Some products require Enter to be
pressed after channel selection.
6. ENTERUsed after direct channel number entry to
immediately change to the selected channel.
7. INFO/SELECT Displays/selectson-screenchannel
information, etc.
8. MENU Access the Menu functions of the device
you are controlling.
9. RECORD,PLAY,STOP,REW,FF,PAUSE VCR
control buttons operate your VCR even when the
remote is set to operate the TV. Also operates DVD
Scan-/+.
10. UP, DOWN, LEFT& RIGHTnavigationbuttons.
11. QUIT Usedtoexit menufunctions.
12. OK Selects menu items for the device you are
controlling.
13. GUIDE Displays on-screen program guide.
14. TV/VCR/INPUTFor some TVs, press repeatedly to
select from available viewing sources (antenna,
cable box, VCR, etc.).
15. CHAPTER+/-controls DVD/CDtrackselection i.e.
DVD/CDTrackSkip Up/Down(inDVD andSAT
modes). Note the VCR buttons also control DVD
when in DVD Mode.
16. MUTE TurnsofftheTV sound whilethepicture
remains.
17. VOLUME UP/DOWNChanges thevolumelevel of
the product, normally the TV.
18. PREV. CHAN Returns to the previously selected
channel, or DVD repeat toggle.
19. SETUP Usedforsetup.
20. POWER Turns product On or Off.
MRU3500-OM_H14102.pmd 9/6/2006, 4:07 PM4-5
1.
2.
3.
4.
5.
6.
7.
8.
9.
20.
19.
18.
17.
16.
15.
14.
13.
12.
11.
10.

76
Setup
Battery Installation
1. On the back of the remote,
push down on the tab and
lift the cover off.
2. Match the batteries to the
+ and - marks inside the
battery case, then insert 2
AAAAlkalinebatteries.
3. Press the battery cover
back into place.
Battery Saver
Your remote automatically turns off if the buttons are
depressed more than 30 seconds. This will save your
batteries should your remote get stuck in a place where
the buttons remain depressed (e.g., between the sofa
cushions).
Code Saver
You will have up to 10 minutes to change the batteries
in your remote without losing codes you have
programmed. However, do not press any buttons until
batteries are installed in the remote. If buttons are
pressed without batteries in the remote, all codes will be
lost.
Power-OnDefault
The remote powers on in TV mode.
CodeSetup
The SETUP button is used to setup the remote. You can
either setup the remote using the code for your brand of
product, from the code tables (on separate sheet), or
you can search through the library of codes until you
find a code that works for your product.
Please refer to “Programming with Code Search” on page
8 for more information on using the code search feature
to learn how to search through the library of codes for
your products.
NOTE: You can store any kind of code under any mode
(except TV). I.E. you can store a VCR code under the
CBL button, or a DVD code under theVCR button, etc.
However, you can only store TV codes under the TV
button.
Button Functions, cont.
DVD Functions (labeled in Blue)
SCAN+ and SCAN- buttons control the speed of Fast
Forward and Reverse Playback respectively.
CHAPTER+andCHAPTER-buttons respectively
locate the succeeding or preceding Chapters or Tracks
on a disc.
REPEATA-Bbutton performs DVD players “A-B
Repeat” (or RPT A.B) function for repeat play of current
Chapter or Track.
INFO/SELECT buttonbringsupDVDDisplay or
ControlMenufor Chapter/Track/Titlenumber,Time
remaining/elapsed indication, system information, etc.
MENU brings up the DVD disc Menu screen - use with
theUP,DOWN, LEFT& RIGHTnavigationbuttons.
OK button is used for on-screen Menu selection. Note
some DVD players require the Play button to be used.
SUBTITLEON-OFF(CC)Turns the subtitles on or off.
QUITExit On-Screen Menus and/or Return to previous
On-Screenselection.
Note, not all DVD Players support all the functions
described above.
SAT Functions
GUIDE button displays on-screen Satellite Channel
Guide.
CHAPTER+ andCHAPTER-buttonsperformthe
“Page+” and “Page-” function for on-screen Guide
Menus used by some Satellite systems.
INFO/SELECT button brings up Satellite Display screen
for current Channel and system information.
MENU brings up the Satellite Menu screen - use with the
UP, DOWN, LEFT& RIGHTnavigationbuttons.
OK button is used for on-screen Menu selection.
QUIT button is used to Exit or Clear on-screen Menu
displays.
TV/VCR/INPUT
When in TV mode the TV/VCR/INPUT buttonperforms
the INPUT source switch function.
When in a mode that has been programmed for VCR the
TV/VCR/INPUTbuttonperformsthe TV/VCRantenna
switch function.
When in a mode that has been programmed for Cable the
TV/VCR/INPUT buttonperforms theA.B switch
function.
When in a mode that has been programmed for SAT the
TV/VCR/INPUT buttonperforms theTV/SAT switch
function.
When in a mode that has been programmed for DVD the
TV/VCR/INPUT buttonperforms theDVD Setup
function.
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM6-7

98
Most users will store VCR codes under the VCR button,
Cable codes underCABLE, etc. If (for example) you
want to store a VCR code underCABLE, first follow the
procedure for Direct Code Entry (previous page) and
press CABLEin step 2 of Direct Code Entry, then enter
ANY VCR code in step 3 of Direct Code Entry.Then
follow the steps above for Code Search (or Brand
Search, below). Note: If the device does not have a
CHANNEL UP button, usePLAY(VCRonly)or
POWER instead. Code Search starts from the currently
stored 4 digit number under that mode.
Code Search, cont.
Code Search by Brand
Lets you search for a code for a specific Brand within
the Code Library for a particular manufacturer.
1. Turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold theSETUP button until the red
indicator remains on, then releaseSETUP button.
3. Press and quickly release the desired mode button
(TV, VCR, etc.). The red indicator blinks off once.
4. Press and release the numeric button (0-9)
corresponding to desired Manufacturer (see table on
code list sheet). The red indicator blinks off once.
Note, pressing “0” performs a full library search same
as normal Code Search Method on previous page.
5. Press theCHANNEL UP button ((orPOWER or
PLAY (VCR only)) repeatedly until the device to be
controlled changes channel.The red indicator blinks
off with each button press. If you accidentally
overshoot the code required, press theCHANNEL
DOWNbutton to backtrack through the library until
the device changes channel. PressingCHANNEL
UP changes direction to forward again.
6. Press and releaseMUTE to install the code.
Brand Search Method entry is now complete.
Note:When all codes under a Brand have been searched
the red indicator flashes rapidly for 3 seconds.
Direct Code Entry
1. Press and hold theSETUP button until the red
indicator stays on, then release theSETUP button.
2. Press and release the desired mode button (TV,
VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables (on
separate sheet). Note: after a valid code entry, the
red indicator turns off. For an invalid code, the red
indicator flashes.
4. Withyourdevice on, pressCHANNELUP. Ifthe
device responds, no further programming is required.
Note: If some buttons do not operate your equipment,
try one of the other codes for your brand.
Write your codes down here for easy reference later.
Code Search
If your product does not respond after you have tried all
the codes for your brand, or if your brand is not listed,
try searching for your code by following these steps.
1. Manually turn on the device (TV, VCR, etc.) to be
controlled.
2. Press and hold theSETUP button until the red
indicator stays on, then release theSETUP button.
3. Press and quickly release the desired mode button
(TV, VCR, etc.). The red indicator blinks off once.
4. Press the CHANNEL UP button repeatedly (up to
300 times) until the device to be controlled changes
channel. The red indicator blinks off with each
button press. If you accidentally overshoot the
code required, press the CHANNEL DOWNbutton
to backtrack through the library until the device
changes channel. PressingCHANNELUP changes
direction to forward again.
5. Press and releaseMUTE to install the code.
Type Type stored Code
TV TV
VCR
DVD
CBL
SAT
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM8-9

1110
ProgrammingComboDeviceCodes
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device. For
example, if you have a TV/DVD Combo, you might need
to set up one code under the TV button to control the
TV part AND a separate code (under any other Mode
button) to control the DVD part.
ControllingComboDevices
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) have separate buttons on the original remote
to select the part of the Combo device to be controlled.
For example, if your Combo device is a DVD/VCR then
its original remote might have separate DVD and VCR
buttons for selection of the Combo part you would
control. The equivalent button functions can be found
on your Magnavox remote by using the device Mode
and SETUP buttons.
Referring to “Programming with Code Search” on page
8, setup a device Mode (e.g. DVD)with the correct code
for your Combo device. Assuming the DVD/VCR
Combo device is the example and its code is
programmed underDVD Mode, press and hold the
DVD Mode button for more than one second to send
the DVD button command. To send the VCR button
command, quickly press and release theSETUP button
followed by pressing and releasing the DVDMode
button. This method can be applied similarly to all
Combodevices(e.g. TV/VCR,TV/DVD,DVD/VCR, etc.)
and is available for all Modes. Note this feature is not
supported by all codes.
ControllingDevicesRequiringSeparatePowerOnand
OffButtons
Some devices (e.g. certain RCA TVs) require separate
Power On and Power Off buttons to turn the device on
and off. The equivalent button functions can be found
on your Magnavox remote by using the device Mode
and POWERbuttons. Referring to “Programming with
Code Search” on page 8, setup a device Mode (e.g. TV)
with the correct code for your device.
Assuming a TV device is the example and its code is
programmed underTV Mode, to turn your TV on, press
and hold the TV Mode button for more than one
second to transmit the Power On button command.
Setup, cont.
Code Identification Feature
The Code Identification Feature allows you to identify
the 4 digit library code stored under your device key. For
example, if you want to find out what 4 digit code is
stored under your TV device key, follow the six steps
below:
1. Press and hold theSETUP button until the red
indicator stays on. Release theSETUPbutton.
2. Press and release the desired mode button (TV,
VCR, etc.). The red indicator blinks, then stays lit.
3. Press and release the SETUPbutton. The red
indicatorblinksoff.
4. To find the first digit for the code stored under the
mode key pressed in step 2, press each numeric key
from 0-9in turn. When the red indicator blinks off
the number you pressed is the first digit for the code
you are searching for.
5. To find the second digit, repeat step 4, this time
when the red indicator blinks off this is the second
digit.
6. Repeat step 4 to find the third and fourth digits.
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM10-11

1312
AnyModechosenforVolume/MutecontrolMUSThave
itsownVolume/Mute functionortheVolume/Mute
buttonswilldonothing.
SettingALLVolume/MuteControltoanyoneMode
This routine can set all Modes to “punch-through” to
any one chosen Mode for Volume/Mute button control
without the needing to change to that Mode.
1. Press and hold theSETUP button until the red
indicator turns on, then release the button.
2. Press and hold theMUTE button until the red
indicator blinks off, then release the button.
3. Press and release the desired Mode button (TV,
VCR, etc.) for Volume/Mute control, the red
indicator blinks then stays on.
4. Press and release theMUTE button and the red
indicator turns off. The red indicator will blink
rapidly for three seconds if the Mode you have
selected has no Volume/Mute control.
5. All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
6. All “Visual” and “Audio” programmed Modes will
now punch-through to the respective Modes you
have chosen for Volume/Mute control.
SettinganyModetouse its ownVolume/MuteControl
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode has
no Volume/Mute functions of its own then the Volume/
Mute buttons will do nothing.
1. Press and hold theSETUP button until the red
indicator turns on, then release the button.
2. Press and hold theMUTE button until the red
indicator blinks off, then release the button.
3. Press and release the desired Mode button (TV,
VCR, etc.), the red indicator blinks then stays on.
4. Press and release the VOLUME-(Down) button, the
red indicator blinks then stays on.
5. Press and release theMUTE button and the red
indicator turns off.
6. All “Visual” and “Audio” programmed Modes will
now punch-through to the respective Modes you
have chosen for Volume/Mute control.
Setup, cont.
ControllingDevicesRequiringSeparatePowerOnand
OffButtons,cont.
To turn the TV off, press and release thePOWER
button to transmit the Power Off button command. This
method can be applied similarly to any device and is
available for all Modes. Note this feature is not
supported by all codes.
VCR/DVD/DVRPunch-ThroughFeature
This remote allows the 6 VCR transport buttons (i.e.
PLAY, PAUSE,STOP,FF,REWIND, andREC) to
Punch-Through control from any Mode programmed
withTV, SAT or Cable codes to the lastVCR, DVDor
DVRprogrammed Mode you used. Normally other
types of remotes only punch-through (from another
Mode) on the 6 VCR buttons to the device programmed
under the VCR Mode button. This is not much use if
you are using a DVD programmed under a Mode other
than VCR. For example, if you have 2 DVD, VCR or DVR
devices programmed into this remote, the last one you
accessed on the remote will be the one that has control
of the 6 VCR transport buttons when in any other
Mode. This feature will not operate if the programmed
TV, SAT or Cable code has its own VCR transport
button control e.g. a TV Combo, SAT/PVR, etc.
Volume/MuteControlandPunch-ThroughFeature
This remote lets you select which device Mode controls
yourVolume/Mute buttons. The remote is initially set
(factory default) for all device Modes programmed with
“Visual” codes (e.g. TV,VCR,DVD, DVR,SAT &
CABLE) and “Audio” codes (e.g. CD & AUDIO) to use
their own Volume/Mute control if present. If the
programmed “Visual” code has no Volume/Mute
operation of its own then those buttons will punch-
through control to the TV Mode device without
needing to change to TV Mode. Please refer to the next
page for more information.
Setup, cont.
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM12-13

1514
Troubleshooting
Remotedoesnot operateyourproduct.
•Press the mode button of the product you want to
control.
•Program the remote with a new code.
•Install new batteries. (You might have to reprogram
your remote after installing new batteries.)
•Remote may not be compatible with your product.
Remotedoesnotoperate some featuresofyourproduct.
•Program remote with a new code.
•Remote may not be able to operate all features of
your product or button names might be different
than your product.
RedIndicatorblinksafter you programaproductcode.
•Remote did not accept the code.
•Try to program the code again or try a different
code.
For help with setup, please call: 919-573-7854.
The manufacturer warrants that this product shall be free
from defects in material, workmanship and assembly,
under normal use, in accordance with the specifications
and warnings, for as long as you own this product. This
warranty extends only to the original purchaser of the
product, and is nontransferable. Defective products,
together with the dated proof of purchase, must be
returned to the place of purchase for repair or
replacement.THEREARENOOTHEREXPRESS
WARRANTIES. Incidental and consequential damages
are disclaimed where permitted by law. This warranty
gives you specific legal rights, and you may also have
other rights which vary from state to state.
Made in China. Quality Assured in USA.
Ledgewood,NJ07852
LimitedLifetimeWarranty
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM14-15

1716
Introducción
Felicitaciones por su compra del Control remoto
universal Magnavox. Los controles Magnavox le
permiten sustituir un control remoto descompuesto
o perdido, o combinar más de un control remoto en
una sola unidad. Además, ¡este control remoto está
equipado con una función de transferencia de
comandos que le permite transferir los comandos
de su equipo de control remoto original!
Este control remoto opera las funciones comunes
de la mayoría de los modelos y marcas de equipo
de video de control por rayos infrarrojos (pero no
de todos). Este control remoto puede ofrecer
funciones que no estén disponibles en su equipo.
Es posible que algunas funciones de su equipo en
particular (por ej., menú de funciones) no se
puedan controlar con este control remoto. En tal
caso, utilice el control remoto original de su equipo.
Por favor, use este manual para familiarizarse con
su control remoto universal Magnavox. Después
de familiarizarse con él, la primera cosa que tiene
que hacer es colocar las baterías y preparar su
control remoto para su aparato y marca en particu-
lar.
Gracias por comprar un control remoto Magnavox
y esperamos que le brinde muchos años de
servicio.
Índice
Introducción ...................................................... 17
Funciones de botones ................................... 18
Funciones de DVD y Satélite ....................... 20
TV/Videocasetera/Entrada................................ 20
Preparación....................................................... 21
Instalación de baterías.................................. 21
Ahorrador de baterías .................................. 21
Almacén de códigos ..................................... 21
Encendido por omisión.................................. 21
Fijación de códigos ....................................... 21
Ingreso de códigos ............................................ 22
Ingreso directo de códigos ............................ 22
Búsqueda de códigos.................................... 22
Búsqueda de códigos por marca ................... 23
Identificación de códigos ................................... 24
Códigos de programación de
equipos combinados .......................................... 25
Control de equipos combinados ......................... 25
Control de equipos con Encendido y Apagado ... 25
Control de VCR/DVD/DVR ............................. 26
Control de volumen/silencio ............................... 26
Ajuste de control volumen/silencio..................... 27
Ajuste de cualquier modo para utilizar su
propio control de volumen/silencio ..................... 27
Localización y reparación de averías ................. 28
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM16-17

1918
Funciones de botones
Funciones de botones
Nota: el botón REC debe oprimirse DOS VECES para grabar
en su videocasetera. Para algunas marcas de
videocaseteras será necesario que oprima el botón REC una
sola vez y enseguida oprimirlo nuevamente durante tres
segundos.
Algunos botones del control remoto pueden tener funciones
con diferentes nombres en el aparato que está controlando.
Por ej, el canal anterior (PREV.CHAN) puede llamarse
RECALL, o ENTER puede llamarse DISPLAY. Estas
diferencias dependen de la marca y del modelo de su aparato.
Además, este control remoto puede operar únicamente las
funciones que existen en su producto. Por ejemplo, su
producto debe estar equipado con canal anterior
(PREV.CHAN) para que el botón dePREV.CHANfuncione.
1. Indicador luminoso rojo se enciende cuando se presiona
cualquier botón.
2. TV, VCR, CBL, DVD, SAT Selecciona el equipo que se va a
usar.
3. CC (SUBTITLE) [Trascripción del audio en pantalla
(subtítulos)] Activa y desactiva la función de trascripción
del audio en pantalla del televisor (si el televisor tiene esta
característica) o los subtítulos de DVD.
4. CHANNELUP/DOWN (Canal siguiente/anterior) Cambia
de canal.
5. NUMEROS oprima los números para la selección
directa de canales. Algunos aparatos requieren que se
oprima Enter después de la selección del canal.
6. ENTER (Ingresar) Se utiliza después del acceso directo de
canales para cambiar inmediatamente al canal seleccionado.
7. INFO/SELECT Trae la pantalla o el Menú de control
del TV, DVD o Satélite para indicar el numero de
Capitulo/Pista/Titulo, el tiempo restante/transcurrido,
información del sistema, etc.
8. MENU Trae la pantalla del Menú de discos del DVD:
Úselo con los botones de navegación hacia arriba, abajo,
izquierda y derecha.
9. RECORD,PLAY,STOP,REW,FF,PAUSE(Grabar,
reproducir, parar, devolver, adelantar, pausa) los botones de
control de la videocasetera hacen funcionar este aparato incluso
cuando el control remoto esta en la modalidad de TV. También
ejecuta la función DVD Scan +/- (exploración +/- de DVD).
10. UP, DOWN, LEFT & RIGHT Botones de navegación
(arriba, abajo, izquierda y derecha).
11. QUIT (Salir)Se utiliza para salir de las funciones del
menú.
12. OK (Aceptar) Se utiliza para la selección del Menú en
pantalla.
13. GUIDE (Guía) Presenta en pantalla la guía de
programación.
14. Botón de TV/VCR/INPUT (televisión, videocassetera,
entrada) Para algunos televisores, oprima este botón
repetidamente para seleccionar una de las fuentes
disponibles para recibir la imagen (antena, videocasetera,
etc.).
15. CHAPTER +/- (Capitulo +/-) Controla la selección de
pistas de DVD/CD, es decir, la pista de DVD/CD para
subir/bajar (en modalidades de DVD y SAT). Observe que
los botones de movimiento de la videocasetera también
controlan el DVD cuando está en la modalidad de DVD.
16. MUTE (Silencio) apaga el sonido de la TV mientras que
permanece la imagen.
17. VOLUME UP/DOWN (Subir/bajar volumen) Cambia el
nivel de volumen del equipo, normalmente el del televisor.
18. PREV. CHAN (Canal anterior) Regresa al canal
seleccionado previamente, o botón para repetir el DVD.
19. SETUP (Configurar) Función emplea da para la
configuración del control remoto.
20. POWER (Encendido) Enciende o apaga el equipo.
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM18-19
1.
2.
3.
4.
5.
6.
7.
8.
9.
20.
19.
18.
17.
16.
15.
14.
13.
12.
11.
10.

2120
Preparación
Funciones de botones
Instalación de baterías
1. En la parte posterior de su control
remoto empuje hacia abajo la
lengüeta y levante la tapa.
2. Acomode dos baterías alcalinas
AAA de manera que coincidan los
polos positivo y negativo dentro
del compartimiento de las
baterías.
3. Acomode la tapa de las baterías
en su lugar.
Ahorrador de baterías
Su control remoto se desactiva automáticamente si los
botones se oprimen más de 30 segundos continuos. Esto
permite que las baterías conserven su carga en caso de que el
control remoto se atore en un lugar donde los botones se
puedan oprimir solos (por ejemplo, entre los cojines del
sofá).
Almacén de códigos
Tiene hasta 10 minutos para cambiar las baterías de su
control remoto sin perder los códigos que ha programado. Sin
embargo, no oprima ningún botón hasta que las baterías estén
instaladas. Si se oprimen botones sin las baterías puestas, se
perderán todos los códigos.
Encendido por omisión
El control remoto se enciende en la modalidad de TV
Fijación de códigos
El botón SETUP (configurar) se utiliza para fijar el control
remoto. Puede fijar el control utilizando el código de su marca
de aparato, de las tablas de códigos (vea la hoja separada), o
puede buscar en la biblioteca de códigos hasta que encuentre
un código que funcione para su aparato. Por favor consulte la
sección de “Programación con búsqueda de códigos” en la
página 22 para obtener más información sobre el uso de la
función de búsqueda de códigos y aprender a hacer una
búsqueda en la biblioteca de códigos para sus productos.
NOTA: También puede almacenar cualquier tipo de código
bajo cualquier modalidad (salvo TV). Es decir, puede
almacenar un código de videocasetera en el botón CBL, o un
código de cable en el botón de VCR, etc. Sin embargo,
únicamente puede almacenar códigos de TV en el botón de
TV.
Funciones de DVD (con leyendas en azul)
Los botones SCAN+ y SCAN- controlan la velocidad para
adelantar o retroceder la reproducción respectivamente.
Los botones CHAPTER+ y CHAPTER- localizan
respectivamente los capítulos o pistas siguientes o
precedentes de un disco.
El botón REPEAT hace las funciones “A-B REPEAT” (o
RPT A.B) de los reproductores de DVD para repetir la
reproducción del capítulo o pista actual.
El botón INFO/SELECT trae la pantalla o el Menú de
control del DVD para indicar el número de Capítulo/Pista/
Título, el tiempo restante/transcurrido, información del
sistema, etc.
MENU Trae la pantalla del Menú de discos del DVD: Úselo
con los botones de navegación hacia arriba, abajo, izquierda y
derecha.
OK (Aceptar) Se utiliza para la selección del Menú en
pantalla.
SUBTITLE (CC) [Transcripición en pantalla, subtítulos]
Activa y desactiva la función de transcripción del audio en
pantalla o los subtítulos de DVD.
El botón Quit se utiliza para salir o despejar las pantallas del
menú. Nota, no todos los reproductores de DVD utilizan
todas las funciones descritas arriba.
Funciones de Satélite
El botón “Guide” presenta en pantalla la guía del canal de
satélite.
Los botones “Chapter+” y “Chapter-” realizan la función
de “Page+” y “Page-” para los menús de guía en pantalla
utilizados en algunos sistemas de satélite.
El botón “Info/Select” trae la pantalla de satélite que indica
la información actual del canal y del sistema.
Menu trae la pantalla del menú de satélite. Úselo con los
botones de navegación hacia arriba, abajo, izquierda y
derecha.
El botón OK se utiliza para la selección del Menú en
pantalla.
El botón Quit se utiliza para salir o despejar las pantallas del
menú.
TV/Videocasetera/Entrada
Cuando está en la modalidad de TV, el botón TV/VCR/
INPUT realiza la función de cambio de fuente de
ENTRADA.
Cuando está en una modalidad que se ha programado para la
videocasetera (VCR), el botón TV/VCR/INPUT realiza la
función de cambio de antena de TV/VCR.
Cuando está en una modalidad que se ha programado para
Cable, el botón TV/VCR/INPUT realiza la función de cambio
A.B.
Cuando está en una modalidad que se ha programado para
SAT, el botón TV/VCR/INPUT realiza la función de cambio
de TV / SAT.
Cuando está en una modalidad que se ha programado para
DVD, el botón TV/VCR/INPUT realiza la función de ajuste
inicial de DVD.
MRU3500-OM_H14102.pmd 9/6/2006, 4:08 PM20-21