Magnetek inteleSmart2 User manual

inteleSmart2 RECEIVER
Engineered
AC/DC Relay Receiver
Part Number: 198-80102-0002 R1
June 2016
© 2016 Magnetek

Your New Radio Receiver
Thank you for your purchase of Magnetek’s inteleSmart2 Receiver Radio Remote Equipment Control.
Magnetek has set a whole new standard in radio-remote performance, dependability, and value with this
line of modular receivers.
If your product ever needs modification or service, please contact one of our representatives at the
following locations:
U.S. Service Information
For questions regarding service or technical information contact:
1.866.MAG.SERV
1.866.624.7378
International Service:
+1.262.783.3500
Magnetek, Inc.
N49 W13650 Campbell Drive
Menomonee Falls, WI 53051
Telephone: [phone]
Website: www.magnetek.com
E-mail: [e-mail]
Fax Numbers:
Main: +1.800.298.3503
Sales: +1.262.783.3510
Service: +1.262.783.3508
Canada Service Information:
161 Orenda Road
Unit 1
Brampton, Ontario
L6W 1W3 Canada
Phone: [phone]
Fax: [phone]
EU Market Contact:
Brian Preston
Magnetek (UK) Ltd.
Unit 3 Bedford Business Centre, Mile Road
Bedford, MK42 9TW UK
Phone: [phone]
Fax: [phone]
©2016 MAGNETEK
All rights reserved. This notice applies to all copyrighted materials included with this product, including,
but not limited to, this manual and software embodied within the product. This manual is intended for the
sole use of the person(s) to whom it was provided, and any unauthorized distribution of the manual or
dispersal of its contents is strictly forbidden. This manual may not be reproduced in whole or in part by
any means whatsoever without the expressed written permission of MAGNETEK.

TABLE OF CONTENTS
1.PRODUCT MANUAL SAFETY INFORMATION................................................................................5
2.CRITICAL INSTALLATION CONSIDERATIONS...............................................................................7
2.1GENERAL.....................................................................................................................................7
2.2PERSONS AUTHORIZED TO OPERATE RADIO CONTROLLED EQUIPMENT.......................7
2.3SAFEY INFORMATION & RECOMMENDED TRAINING FOR OPERATORS............................7
2.4PRE-OPERATION TEST..............................................................................................................9
2.5CRANE-SPECIFIC DEVICE WARNINGS ....................................................................................9
3.INTELESMART2 INSTALLATION ...................................................................................................11
3.1PRE-INSTALLATION..................................................................................................................11
3.2RECEIVER UNIT MOUNTING LOCATION CONSIDERATIONS...............................................11
3.3ANTENNA MOUNTING CONSIDERATIONS.............................................................................11
3.4LINE INPUT CONSIDERATIONS...............................................................................................12
3.5WIRING CONSIDERATION........................................................................................................12
3.6RECEIVER/EQUIPMENT INTERFACE CONSIDERATIONS....................................................13
3.7RECEIVER UNIT ENCLOSURE MOUNTING............................................................................13
3.8RECEIVER INSTALLATION.......................................................................................................13
3.9MECHANICAL DRAWINGS........................................................................................................14
4.WIRING............................................................................................................................................16
4.1ALARMS AND HORNS...............................................................................................................16
4.2POWER.......................................................................................................................................16
4.2.1DC Power............................................................................................................................16
4.2.2AC Power............................................................................................................................16
4.3COMMONS.................................................................................................................................17
4.4POWER OR HOT ROUTING......................................................................................................17
4.5MACHINE STOP (MC) RELAYS.................................................................................................17
4.6WIRING DIAGRAMS...................................................................................................................17
4.6.1Wiring Isolation Options......................................................................................................19
4.7CONNECTING OUTPUTS TO DRIVES.....................................................................................19
4.8ANALOG INPUT..........................................................................................................................19
4.9DIGITAL INPUTS........................................................................................................................20
4.10EXPANSION MODULES ............................................................................................................20
5.NORMAL OPERATION....................................................................................................................21
5.1INITIALIZATION..........................................................................................................................21
6.INTELESMART2 EXPANSION MODULE TYPES...........................................................................23
6.1RELAY EXPANSION MODULE..................................................................................................23
7.PROGRAMMING WITH RCP ..........................................................................................................26
7.1ACCESS CODES........................................................................................................................26
7.2CHANGING ACCESS CODES...................................................................................................26
7.3CONNECTING THE INTELESMART2 TO A COMPUTER ........................................................27
7.4PROGRAMMING WITH RCP .....................................................................................................27
7.4.1inteleSmart2 Configuration Page........................................................................................30
7.4.2Programming Page .............................................................................................................34
7.4.3FDP Page............................................................................................................................35
7.4.4Saving, Downloading, And Reading The Programs And Other RCP Software Functions .36
8.RECEIVER CHANNEL CONFIGURATION SETTINGS..................................................................38
8.1FCC STATEMENTS....................................................................................................................38
8.2433MHz CHANNEL SET.............................................................................................................39

8.3433 MHz Telemotive Legacy Channel Set..................................................................................40
8.4900MHz CHANNEL SET.............................................................................................................41
8.5419MHz CHANNEL SET.............................................................................................................42
8.62.4 GHz: FHSS............................................................................................................................43
9.TROUBLESHOOTING.....................................................................................................................44
9.1TROUBLESHOOTING TABLE....................................................................................................45
9.2RECEIVER SPECIFICATIONS...................................................................................................48
9.3ASSEMBLY AND REPLACEMENT PARTS...............................................................................48
10.NOTES.............................................................................................................................................49

inteleSmart2 Instruction Manual
June 2016
Page 5 of 49
1. PRODUCT MANUAL SAFETY INFORMATION
Magnetek, Inc. (Magnetek) offers a broad range of radio remote control products, control products and
adjustable frequency drives, and industrial braking systems for overhead material handling applications.
This manual has been prepared by Magnetek to provide information and recommendations for the
installation, use, operation and service of Magnetek’s material handling products and systems (Magnetek
Products). Anyone who uses, operates, maintains, services, installs or owns Magnetek Products should
know, understand and follow our instructions and safety recommendations in this manual for Magnetek
Products.
The recommendations in this manual do not take precedence over any of the following requirements
relating to cranes, hoists and lifting devices:
Instructions, manuals, and safety warnings of the manufacturers of the equipment where the
radio system is used,
Plant safety rules and procedures of the employers and the owners of facilities where the
Magnetek Products are being used,
Regulations issued by the Occupational Health and Safety Administration (OSHA),
Applicable local, state or federal codes, ordinances, standards and requirements, or
Safety standards and practices for the overhead material handling industry.
This manual does not include or address the specific instructions and safety warnings of these
manufacturers or any of the other requirements listed above. It is the responsibility of the owners, users
and operators of the Magnetek Products to know, understand and follow all of these requirements. It is
the responsibility of the owner of the Magnetek Products to make its employees aware of all of the above
listed requirements and to make certain that all operators are properly trained. No one should use
Magnetek Products prior to becoming familiar with and being trained in these requirements.
WARRANTY INFORMATION
FOR INFORMATION ON MAGNETEK’S PRODUCT WARRANTIES BY PRODUCT TYPE, PLEASE VISIT
WWW.MAGNETEK.COM.

inteleSmart2 Instruction Manual
June 2016
Page 6 of 49
WARNINGS and CAUTIONS
Throughout this document WARNING and CAUTION statements have been deliberately placed to
highlight items critical to the protection of personnel and equipment.
WARNING – A warning highlights an essential operating or maintenance procedure, practice, etc.
which if not strictly observed, could result in injury or death of personnel, or long term physical
hazards. Warnings are highlighted as shown below:
WARNING
CAUTION – A caution highlights an essential operating or maintenance procedure, practice, etc.
which if not strictly observed, could result in damage to, or destruction of equipment, or loss of
functional effectiveness. Cautions are highlighted as shown below:
CAUTION
WARNINGS and CAUTIONS SHOULD NEVER BE DISREGARDED
The safety rules in this section are not intended to replace any rules or regulations of any applicable local,
state, or federal governing organizations. Always follow your local lockout and tagout procedure when
maintaining any radio equipment. The following information is intended to be used in conjunction with
other rules or regulations already in existence. It is important to read all of the safety information
contained in this section before installing or operating the Radio Control System.

inteleSmart2 Instruction Manual
June 2016
Page 7 of 49
2. CRITICAL INSTALLATION CONSIDERATIONS
WARNING
PRIOR TO INSTALLATION AND OPERATION OF THIS EQUIPMENT, READ AND DEVELOP AN
UNDERSTANDING OF THE CONTENTS OF THIS MANUAL AND THE OPERATION MANUAL OF THE
EQUIPMENT OR DEVICE TO WHICH THIS EQUIPMENT WILL BE INTERFACED. FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.
FOLLOW YOUR LOCAL LOCKOUT TAGOUT PROCEDURE BEFORE MAINTAINING ANY REMOTE
CONTROLLED EQUIPMENT. ALWAYS REMOVE ALL ELECTRICAL POWER FROM THE EQUIPMENT BEFORE
ATTEMPTING ANY INSTALLATION PROCEDURES. DE-ENERGIZE AND TAGOUT ALL SOURCES OF
ELECTRICAL POWER BEFORE TOUCH-TESTING ANY EQUIPMENT. FAILURE TO FOLLOW THIS WARNING
COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.
AFTER INSTALLATION BE SURE TO VERIFY THAT THE TRANSMITTER IS NOT INTERFERING WITH OTHER
EQUIPMENT IN THE AREA. ALSO VERIFY THAT OTHER EQUIPMENT IS NOT INTERFERING WITH THE
TRANSMITTER AND ITS ASSOCIATED EQUIPMENT. FAILURE TO FOLLOW THESE WARNINGS COULD
RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.
2.1 GENERAL
Radio controlled equipment operates in several directions. Quite frequently, the equipment is operated in areas
where people are working in close proximity to the equipment. The operator must exercise extreme caution at all
times. Workers must constantly be alert to avoid accidents. The following recommendations have been included to
indicate how careful and thoughtful actions may prevent injuries, damage to equipment, or even save a life.
2.2 PERSONS AUTHORIZED TO OPERATE RADIO CONTROLLED
EQUIPMENT
Only properly trained persons designated by management should be permitted to operate radio controlled equipment.
Radio controlled equipment should not be operated by any person who cannot read or understand signs, notices and
operating instructions that pertain to the equipment.
Radio controlled equipment should not be operated by any person with insufficient eyesight or hearing or by any
person who may be suffering from a disorder or illness, is taking any medication that may cause loss of equipment
control, or is under the influence of alcohol or drugs.
2.3 SAFEY INFORMATION & RECOMMENDED TRAINING FOR
OPERATORS
Anyone being trained to operate radio controlled equipment should possess as a minimum the following knowledge
and skills before using the radio controlled equipment.
The operator should:
have knowledge of hazards pertaining to equipment operation
have knowledge of safety rules for radio controlled equipment

inteleSmart2 Instruction Manual
June 2016
Page 8 of 49
have the ability to judge distance of moving objects
know how to properly test prior to operation
be trained in the safe operation of the radio transmitter as it pertains to the equipment being operated
have knowledge of the use of equipment warning lights and alarms
have knowledge of the proper storage space for a radio control transmitter when not in use
be trained in transferring a radio control transmitter to another person
be trained how and when to report unsafe or unusual operating conditions
test the transmitter emergency stop and all warning devices prior to operation; testing should be done on
each shift, without a load
be thoroughly trained and knowledgeable in proper and safe operation of the equipment that utilizes the
radio control
know how to keep the operator and other people clear of hazardous areas
know and follow the local lockout and tagout procedures when servicing radio controlled equipment
know and follow all applicable operating and maintenance manuals, safety procedures, regulatory
requirements, and industry standards and codes
The operator shall not:
operate the equipment if the direction of travel or function engaged does not agree with what is indicated on
the controller
operate any damaged or malfunctioning equipment
change any settings or controls without authorization and proper training
remove or obscure any warning or safety labels or tags
leave power on the radio controlled equipment when the equipment is not in operation
operate any equipment using a damaged controller because the unit may be unsafe
operate manual motions with other than manual power
operate radio controlled equipment when low battery indicator is on
WARNING
THE OPERATOR SHOULD NOT ATTEMPT TO REPAIR ANY RADIO CONTROLLER. IF ANY PRODUCT
PERFORMANCE OR SAFETY CONCERNS ARE OBSERVED, THE EQUIPMENT SHOULD IMMEDIATELY
BE TAKEN OUT OF SERVICE AND BE REPORTED TO THE SUPERVISOR. DAMAGED AND INOPERABLE
RADIO CONTROLLER EQUIPMENT SHOULD BE RETURNED TO MAGNETEK FOR EVALUATION AND
REPAIR. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND
DAMAGE TO EQUIPMENT.

inteleSmart2 Instruction Manual
June 2016
Page 9 of 49
2.4 PRE-OPERATION TEST
At the start of each work shift, or when a new operator takes control of the equipment, operators should do,
as a minimum, the following steps before making lifts with any equipment:
Test all warning devices.
Test all functions.
Test the transmitter machine stop.
2.5 CRANE-SPECIFIC DEVICE WARNINGS
WARNING
ALL EQUIPMENT MUST HAVE A MAINLINE CONTACTOR INSTALLED AND ALL TRACKED CRANES, HOISTS,
LIFTING DEVICES AND SIMILAR EQUIPMENT MUST HAVE A BRAKE INSTALLED. FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.
AN AUDIBLE AND/OR VISUAL WARNING MEANS MUST BE PROVIDED ON ALL REMOTE CONTROLLED
EQUIPMENT AS REQUIRED BY CODE, REGULATION, OR INDUSTRY STANDARD. THESE AUDIBLE AND/OR
VISUAL WARNING DEVICES MUST MEET ALL GOVERNMENTAL REQUIREMENTS. FAILURE TO FOLLOW
THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.
THE DIRECT OUTPUTS OF THIS PRODUCT ARE NOT DESIGNED TO INTERFACE DIRECTLY TO TWO STATE
SAFETY CRITICAL MAINTAINED FUNCTIONS, I.E., MAGNETS, VACUUM LIFTS, PUMPS, EMERGENCY
EQUIPMENT, ETC. A MECHANICALLY LOCKING INTERMEDIATE RELAY SYSTEM WITH SEPARATE POWER
CONSIDERATIONS MUST BE PROVIDED. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN
SERIOUS INJURY OR DEATH OR DAMAGE TO EQUIPMENT.
Cranes, hoists, lifting devices and other material handling equipment can be large, and operate at high speeds.
The operator should:
continuously watch and monitor status of lifted loads
know and follow cable and hook inspection procedures
The operator shall not:
lift or move more than the rated load
use the crane, hoist or lifting device to lift, support or transport people
lift or carry any loads over people
operate the crane, hoist or lifting device unless all persons, including the operator, are and remain clear of
the supported load and any potential pinch points
operate a crane, hoist or lifting device when the device is not centered over the load

inteleSmart2 Instruction Manual
June 2016
Page 10 of 49
operate a crane, hoist or lifting device if the chain or wire rope is not seated properly in the sprockets, drum
or sheave
leave any load unattended while lifted