Magnus PV Series User manual

• Never set up or pull down a tripod while a camera is
mounted
• Do not move the tripod or adjust the legs while a
camera is mounted
• Do not exceed the maximum weight capacity of the
tripod
• Never leave a camera unattended on the tripod
• The camera should be securely fastened to the quick-
release mounting plate before mounting onto the
tripod
• Never mount a camera to the tripod until all tripod
legs are locked and stabilized
• Do not stand on, rest on, or hang anything from the
mid-level spreader
• Do not attempt to remove the mid-level spreader
• Do not lift or move the tripod by the head
• Keep hands clear of the inside of the legs, to avoid
trapping fingers
• The safe operation of the tripod is the responsibility
of the user
Owner’s
Manual
User Cautions
Photo Tripod Components
Thank you for choosing Magnus.
Congratulations on the purchase of your new
Magnus tripod. This tripod features an adjustable
center column for smooth and precise camera height
adjustment, and telescoping legs with flip-locks
for fast and easy leg adjustments. The three-way
pan & tilt head gives you total control over camera
positioning, and the quick-release plate features a
1/4”-20 male thread for universal camera mounting.
There is also a bubble level to ensure that your shot is
properly aligned.
Please read and follow these instructions, and keep
this manual in a safe place.
Platform Orientation
Locking Knob
Universal ¼-20
Mounting Screw
Photo Tripod
PV Series
Tilt/Pan Bar /
Tilt Lock
Center Column
Locking Collar
Center Brace
Locking Knob
Quick-Release
Mounting Plate
Pan Locking
Knob
Leg
Flip-Lock
Image is for illustration purposes only.
Features varies by model
ONE (1) YEAR LIMITED WARRANTY
This Magnus product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer use
for a period of one (1) year from the original purchase date or thirty (30)
days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to
repair or replacement, at the provider’s discretion, of any product that fails
during normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by the
warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT
AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY
EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Thiswarrantyprovides you withspecific
legalrights, andyoumay alsohaveadditional rightsthat varyfromstatetostate.
To obtain warranty coverage, contact the Magnus Customer Service
Department to obtain a return merchandise authorization (“RMA”) number,
and return the defective product to Magnus along with the RMA number and
proof of purchase. Shipment of the defective product is at the purchaser’s
own risk and expense.
For more information or to arrange service, visit www.magnustripods.com or
call Customer Service at 212-594-2353.
MAGNUS
A Gradus Group Brand
TM
Product warranty provided by the Gradus Group. www.gradusgroup.com»
MAGNUS is a registered trademark of the Gradus Group. © 2014 Gradus
Group LLC. All Rights Reserved.
GG2
PV Manual.indd 1 6/13/14 1:10 PM

• Never set up or pull down a tripod while a camera is
mounted
• Do not move the tripod or adjust the legs while a
camera is mounted
• Do not exceed the maximum weight capacity of the
tripod
• Never leave a camera unattended on the tripod
• The camera should be securely fastened to the quick-
release mounting plate before mounting onto the
tripod
• Never mount a camera to the tripod until all tripod
legs are locked and stabilized
• Do not stand on, rest on, or hang anything from the
mid-level spreader
• Do not attempt to remove the mid-level spreader
• Do not lift or move the tripod by the head
• Keep hands clear of the inside of the legs, to avoid
trapping fingers
• The safe operation of the tripod is the responsibility
of the user
Owner’s
Manual
User Cautions
Photo Tripod Components
Thank you for choosing Magnus.
Congratulations on the purchase of your new
Magnus tripod. This tripod features an adjustable
center column for smooth and precise camera height
adjustment, and telescoping legs with flip-locks
for fast and easy leg adjustments. The three-way
pan & tilt head gives you total control over camera
positioning, and the quick-release plate features a
1/4”-20 male thread for universal camera mounting.
There is also a bubble level to ensure that your shot is
properly aligned.
Please read and follow these instructions, and keep
this manual in a safe place.
Platform Orientation
Locking Knob
Universal ¼-20
Mounting Screw
Photo Tripod
PV Series
Tilt/Pan Bar /
Tilt Lock
Center Column
Locking Collar
Center Brace
Locking Knob
Quick-Release
Mounting Plate
Pan Locking
Knob
Leg
Flip-Lock
Image is for illustration purposes only.
Features varies by model
ONE (1) YEAR LIMITED WARRANTY
This Magnus product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer use
for a period of one (1) year from the original purchase date or thirty (30)
days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to
repair or replacement, at the provider’s discretion, of any product that fails
during normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by the
warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT
AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY
EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Thiswarrantyprovides you withspecific
legalrights, andyoumay alsohaveadditional rightsthat varyfromstatetostate.
To obtain warranty coverage, contact the Magnus Customer Service
Department to obtain a return merchandise authorization (“RMA”) number,
and return the defective product to Magnus along with the RMA number and
proof of purchase. Shipment of the defective product is at the purchaser’s
own risk and expense.
For more information or to arrange service, visit www.magnustripods.com or
call Customer Service at 212-594-2353.
MAGNUS
A Gradus Group Brand
TM
Product warranty provided by the Gradus Group. www.gradusgroup.com»
MAGNUS is a registered trademark of the Gradus Group. © 2014 Gradus
Group LLC. All Rights Reserved.
GG2
PV Manual.indd 1 6/13/14 1:10 PM

3To change the camera orientation from horizontal
to vertical position, loosen the platform locking knob
by rotating it counterclockwise. Rotate the platform
90°, and then rotate the platform locking knob
clockwise to lock the new position (Fig. I)
3Make sure the
screwhead handle is
flat against the bottom
of the quick-release
plate. Mount the
camera/quick-release
plate assembly to the
tripod head by pulling
and holding back on
the plate locking lever.
Insert the camera/
quick-release plate
assembly and push the
plate locking lever to
lock it in place (Fig. F)
Utilizing the Pan & Tilt Head
1To utilize the tilt feature, loosen the pan & tilt bar by
rotating it counterclockwise. Tilt the tripod head to
the desired angle, and then rotate the pan & tilt bar
clockwise to lock the new position (Fig. G)
2To utilize the 360° panning feature, loosen
the panning locking knob by rotating it
counterclockwise. Pan as necessary, and then rotate
the panning locking knob clockwise to lock the new
position (Fig. H)
Adjusting the Center Column Height
1To raise or lower the center column, loosen the
center column collar by rotating it counterclockwise
(Fig. J)
2Pull the center
column up to the
desired height, and
then rotate the
center column collar
clockwise to lock the
new position (Fig. K)
Opening the Tripod
1Always extend the legs from the top flip-locks first.
Pull out on each flip-lock and extend the legs to the
desired height. Relock each leg (Fig. A-B)
2Rotate the locking
knob counterclockwise
to release the center
brace, and gently pull
the legs out. Push
down on the center
brace, and then rotate
the locking knob
clockwise to lock the
legs in place (Fig. C)
Mounting the Quick-Release Plate to
the Camera
1To remove the quick-release plate from the tripod
head, pull and hold the plate locking lever and
remove the quick-release plate (Fig. D)
2Line up the quick-release plate lengthwise with the
bottom of the camera. Match the quick-release
plate screw to the camera’s mounting thread, and
mount the plate to the camera by rotating the
screw clockwise until snug (Fig. E)
Figure A Figure B
Figure C
Figure F
Figure E
Figure D
Figure G
Figure H
Figure I
All images are for illustration purposes only. Features
varies by model
Figure J
Figure K
PV Manual.indd 2 6/13/14 1:11 PM

3To change the camera orientation from horizontal
to vertical position, loosen the platform locking knob
by rotating it counterclockwise. Rotate the platform
90°, and then rotate the platform locking knob
clockwise to lock the new position (Fig. I)
3Make sure the
screwhead handle is
flat against the bottom
of the quick-release
plate. Mount the
camera/quick-release
plate assembly to the
tripod head by pulling
and holding back on
the plate locking lever.
Insert the camera/
quick-release plate
assembly and push the
plate locking lever to
lock it in place (Fig. F)
Utilizing the Pan & Tilt Head
1To utilize the tilt feature, loosen the pan & tilt bar by
rotating it counterclockwise. Tilt the tripod head to
the desired angle, and then rotate the pan & tilt bar
clockwise to lock the new position (Fig. G)
2To utilize the 360° panning feature, loosen
the panning locking knob by rotating it
counterclockwise. Pan as necessary, and then rotate
the panning locking knob clockwise to lock the new
position (Fig. H)
Adjusting the Center Column Height
1To raise or lower the center column, loosen the
center column collar by rotating it counterclockwise
(Fig. J)
2Pull the center
column up to the
desired height, and
then rotate the
center column collar
clockwise to lock the
new position (Fig. K)
Opening the Tripod
1Always extend the legs from the top flip-locks first.
Pull out on each flip-lock and extend the legs to the
desired height. Relock each leg (Fig. A-B)
2Rotate the locking
knob counterclockwise
to release the center
brace, and gently pull
the legs out. Push
down on the center
brace, and then rotate
the locking knob
clockwise to lock the
legs in place (Fig. C)
Mounting the Quick-Release Plate to
the Camera
1To remove the quick-release plate from the tripod
head, pull and hold the plate locking lever and
remove the quick-release plate (Fig. D)
2Line up the quick-release plate lengthwise with the
bottom of the camera. Match the quick-release
plate screw to the camera’s mounting thread, and
mount the plate to the camera by rotating the
screw clockwise until snug (Fig. E)
Figure A Figure B
Figure C
Figure F
Figure E
Figure D
Figure G
Figure H
Figure I
All images are for illustration purposes only. Features
varies by model
Figure J
Figure K
PV Manual.indd 2 6/13/14 1:11 PM

3To change the camera orientation from horizontal
to vertical position, loosen the platform locking knob
by rotating it counterclockwise. Rotate the platform
90°, and then rotate the platform locking knob
clockwise to lock the new position (Fig. I)
3Make sure the
screwhead handle is
flat against the bottom
of the quick-release
plate. Mount the
camera/quick-release
plate assembly to the
tripod head by pulling
and holding back on
the plate locking lever.
Insert the camera/
quick-release plate
assembly and push the
plate locking lever to
lock it in place (Fig. F)
Utilizing the Pan & Tilt Head
1To utilize the tilt feature, loosen the pan & tilt bar by
rotating it counterclockwise. Tilt the tripod head to
the desired angle, and then rotate the pan & tilt bar
clockwise to lock the new position (Fig. G)
2To utilize the 360° panning feature, loosen
the panning locking knob by rotating it
counterclockwise. Pan as necessary, and then rotate
the panning locking knob clockwise to lock the new
position (Fig. H)
Adjusting the Center Column Height
1To raise or lower the center column, loosen the
center column collar by rotating it counterclockwise
(Fig. J)
2Pull the center
column up to the
desired height, and
then rotate the
center column collar
clockwise to lock the
new position (Fig. K)
Opening the Tripod
1Always extend the legs from the top flip-locks first.
Pull out on each flip-lock and extend the legs to the
desired height. Relock each leg (Fig. A-B)
2Rotate the locking
knob counterclockwise
to release the center
brace, and gently pull
the legs out. Push
down on the center
brace, and then rotate
the locking knob
clockwise to lock the
legs in place (Fig. C)
Mounting the Quick-Release Plate to
the Camera
1To remove the quick-release plate from the tripod
head, pull and hold the plate locking lever and
remove the quick-release plate (Fig. D)
2Line up the quick-release plate lengthwise with the
bottom of the camera. Match the quick-release
plate screw to the camera’s mounting thread, and
mount the plate to the camera by rotating the
screw clockwise until snug (Fig. E)
Figure A Figure B
Figure C
Figure F
Figure E
Figure D
Figure G
Figure H
Figure I
All images are for illustration purposes only. Features
varies by model
Figure J
Figure K
PV Manual.indd 2 6/13/14 1:11 PM

• Never set up or pull down a tripod while a camera is
mounted
• Do not move the tripod or adjust the legs while a
camera is mounted
• Do not exceed the maximum weight capacity of the
tripod
• Never leave a camera unattended on the tripod
• The camera should be securely fastened to the quick-
release mounting plate before mounting onto the
tripod
• Never mount a camera to the tripod until all tripod
legs are locked and stabilized
• Do not stand on, rest on, or hang anything from the
mid-level spreader
• Do not attempt to remove the mid-level spreader
• Do not lift or move the tripod by the head
• Keep hands clear of the inside of the legs, to avoid
trapping fingers
• The safe operation of the tripod is the responsibility
of the user
Owner’s
Manual
User Cautions
Photo Tripod Components
Thank you for choosing Magnus.
Congratulations on the purchase of your new
Magnus tripod. This tripod features an adjustable
center column for smooth and precise camera height
adjustment, and telescoping legs with flip-locks
for fast and easy leg adjustments. The three-way
pan & tilt head gives you total control over camera
positioning, and the quick-release plate features a
1/4”-20 male thread for universal camera mounting.
There is also a bubble level to ensure that your shot is
properly aligned.
Please read and follow these instructions, and keep
this manual in a safe place.
Platform Orientation
Locking Knob
Universal ¼-20
Mounting Screw
Photo Tripod
PV Series
Tilt/Pan Bar /
Tilt Lock
Center Column
Locking Collar
Center Brace
Locking Knob
Quick-Release
Mounting Plate
Pan Locking
Knob
Leg
Flip-Lock
Image is for illustration purposes only.
Features varies by model
ONE (1) YEAR LIMITED WARRANTY
This Magnus product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer use
for a period of one (1) year from the original purchase date or thirty (30)
days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to
repair or replacement, at the provider’s discretion, of any product that fails
during normal use of this product in its intended manner and in its intended
environment. Inoperability of the product or part(s) shall be determined by the
warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT
AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY
EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Thiswarrantyprovides you withspecific
legalrights, andyoumay alsohaveadditional rightsthat varyfromstatetostate.
To obtain warranty coverage, contact the Magnus Customer Service
Department to obtain a return merchandise authorization (“RMA”) number,
and return the defective product to Magnus along with the RMA number and
proof of purchase. Shipment of the defective product is at the purchaser’s
own risk and expense.
For more information or to arrange service, visit www.magnustripods.com or
call Customer Service at 212-594-2353.
MAGNUS
A Gradus Group Brand
TM
Product warranty provided by the Gradus Group. www.gradusgroup.com»
MAGNUS is a registered trademark of the Gradus Group. © 2014 Gradus
Group LLC. All Rights Reserved.
GG2
PV Manual.indd 1 6/13/14 1:10 PM