MaiLink MLDB2B Series Operator's manual

Electric Height Adjustable Desk Frame
Professional For Health
MLDB2B SERIES
MaiLink
INSTRUCTIONS FOR ASSEMBLY AND USE
Please provide this operation to any users,installer ,or support personnel
operating the product.
Inappropriate use of this product may cause property or bodily injury.
Do not move around,crawl or lie under the desk frame.Do not sit or stand
on the desk frame.
Check that no cables can get jammed.
The desk height is adjustable so that it can be positioned at the most
ergonomically suitable height. The desk are disigned only for the purposes
ncluded in this manual.They should not be used in environments with
high humidity or dampness.
!
WARNING

MLDB2B series parameter instruction
Electric Control Part:
Input Voltage: 100-240V can be use
Output Voltage: 24V DC
Duty cycle: 10%MAX 2min on 18 min off
Switch power supply, low energy consumption
Manual device can move and long press
Desk frame part:
Built-in limit switch
Dynamic load: 70KG
The maximum static load: 140KG
Load speed: 30mm/s
Lift range: 620mm---1270mm
The length of the adjusting range: 1100mm~1600mm
Other part:
Packing Size：1080*270*330mm 2Set
770*175*135mm 1Set
GW:90Kg
Safety and warnings
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
Correct Disposal of this product
This marking indicates that this product should not be disposed
with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from un-
controlled waste disposal ,recycle it responsibly to promote the
sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take
this product for environmental safe recycling.

Desk Frame installation instruction
The overall effect
Leg (4pcs) Tie beam cover
2pcs
Middle beam cover
1pcs
Rail 2pcs
Motor wire 4pcs
Power connecting 2pcs
Middle beam 1pcs
Tie beam 2pcs
Control box 1pcs
Screw
M5*12 20pcs
Screw
M8*10 24pcs Self-tapping screw
ST3.3*16 2pcs
Handset 1pcs
Glides 4pcs
Middle beam cover
bottom 1pcs
hexagonal brass nut

1.Control box install
Lay the rail level(image),fix the control box on the 2rails by 4pcs M6*10 Screw.
2.Install leg part and desk frame
M6*10 Screw(4pcs)
M6*10 Screw(4pcs)
1.Lay the desktop on clean surface, put 4legs and 4pcs frame parts in turn.
2.fix the legs on frame with 24 M8*10 screw
3.screw up 4pcs glides on leg end glides(4pcs)
M8*10 screw
(24pcs)
Installation Guide

Tie up the 2 desks by 2 tie beam connecting by M5*12 screw 8pcs
M5*12 8pcs
Fix the middle beam between the 2 tie bea by M5*12 screw 4pcsm
M5*12 8pcs
3. ie beam installationT
Installation Guide

4.Desktop ins lationtal
A screw, screwdjust the desktop location to certain place using 16pcs of ST6.5*16 the
legs part up on desktop
ST6.5*16 screw
16pcs
Connecting cables 4pcs
Power cords 2pcs
Handset 2pcs
First ,line up control box by 4pcs connecting cables and 2pcs Power cords.
Second, locked the handset on desktop by 4 pcs ST3.3*16.
5.Install Power cords and Connecting cables
Installation Guide
MaiLink

6.Install hexagonal brass nut
Put 8pcs( M5*10+7) hexagonal brass nut on the tie beam.
hexagonal brass nut M5*10+7
7.Install hexagonal brass nut
Screen Mounting Plate 4pcs
Middle beam cover 1pcs
Middle beam cover
bottom 1pcs
M5*12 screw 8pcsTie beam cover
2pcs
Put the Tie beam cover on the tie beam, put the “middle beam cover bottom” on the
middle beam, and put the meddle beam cover on it as picture
Put the Lock the screen Mounting plate with 8 screws(M5*12) on the Tie beam cover.
Installation Guide

Handset Usage Instructions
Mode of operation
1.Lightly touch up/down button and hold the key to rise and low the desk height
2.Press HOME button and quickly release to move the base height(withou work surface)
to a normal desk height of 28.3"
3.To set M1 and M2 height memories press and hole key in for 5 seconds.
Once set in memory, quickly press M1 or M2 to achieve programmed in height.
4.After 30 seconds of not touching the keypad, display screen lights will turn off.
5.To start keypad push either up or down to light up.
116
SAVE
M1 M2 HOME
MaiLink
The height automatically go to
720mm(28.3"). Touch the key and release.
Second memory position. Press and hold the key
for 5 seconds for memory 2.
First memory position. Press and hold the key for 5
seconds for memory 1.
Display screen
Show current height Range from 620mm--1270mm(24.4"--50")
Lowering button. Push and hold to lower desk/table
Raising button. Push and hold to raise desk/table