Makita GA4040 User manual

GB Angle Grinder Instruction manual
ID Gerinda Sudut Petunjuk penggunaan
VI Maùy maøi goùc Taøi lieäu höôùng daãn
TH !"#$%&'!()*+,,-."/01$&2.#345'.6
GA4040
GA4540
GA5040
GA6040
012721

2
1012725 2012728
3012724 4012733
5009430 6009431
7012802 8012727
1
2
3
45
3
4
5
6
56
7
8
9
10
1

3
9012772 10 012773
11 010846 12 010863
13 012740 14 012742
15 012731 16 012730
11
12
13
9
1
14 15
7
16
17
9
18
19
20
21 22
23
24
A
B

4
17 010855 18 012743
19 012744 20 012732
7
25
9
26
27
28
29
30

5
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
•Specificationsmaydifferfromcountrytocountry.
•WeightaccordingtoEPTA-Procedure01/2003
Symbols END202-7
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
...... Read instruction manual.
................ DOUBLE INSULATION
...... Wear safety glasses.
Intended use ENE048-1
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply ENF002-2
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings GEA005-3
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
1. Shaft lock
2. Slide switch
3. Wheel guard
4. Bearing box
5. Screw
6. Lever
7. Lock nut
8. Depressed center wheel
9. Inner flange
10. Lock nut wrench
11. Ezy nut
12. Abrasive wheel
13. Spindle
14. Arrow
15. Notch
16. Flex wheel
17. Plastic pad
18. Sanding lock nut
19. Abrasive disc
20. Rubber pad
21. Marking A
22. Marking B
23. Marking C
24. Marking D
25. Abrasive cut-off wheel/diamond
wheel
26. Wheel guard for abrasive cut-off
wheel/diamond wheel
27. Wire cup brush
28. Wire wheel brush
29. Exhaust vent
30. Inhalation vent
Model GA4040 GA4540 GA5040 GA6040
Wheel diameter 100 mm (4”) 115 mm (4-1/2”) 125 mm (5”) 150 mm (6”)
Max. wheel thickness 6.4 mm
Spindle thread M10 M14 or 5/8” (country specific)
Rated speed (n)/
No load speed (n0)11,000 min-1 11,000 min-1 11,000 min-1 9,000 min-1
Overall length 303 mm 303 mm 303 mm 303 mm
Net weight 2.3 kg 2.4 kg 2.4 kg 2.5 kg
Safety class /II