Makita DTP131 User manual

DTP131
DTP141
EN
Cordless 4 Mode Impact Driver INSTRUCTION MANUAL 4
SL Akumulatorski udarni vijačnik
s 4 načini NAVODILO ZA UPORABO 13
SQ Trapan me goditje me 4
regjime me bateri MANUALI I PËRDORIMIT 22
BG
Акумулаторен ударен
винтоверт с 4 режима на работа
РЪКОВОДСТВО ЗА
ЕКСПЛОАТАЦИЯ 32
HR Akumulatorski udarni odvijač
s 4 načina rada PRIRUČNIK S UPUTAMA 43
МК Безжичен ударен одвртувач
со 4 режими УПАТСТВО ЗА УПОТРЕБА 52
RO
Maşină de înşurubat cu
impact cu 4 moduri de
operare cu acumulator
MANUAL DE INSTRUCŢIUNI 63
SR Бежични ударни одвртач са
4 режима рада УПУТСТВО ЗА УПОТРЕБУ 73
RU
Аккумуляторный 4 режимный
ударный шуруповерт
РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ 83
UK Бездротовий ударний
шуруповерт на 4 режими
ІНСТРУКЦІЯ З
ЕКСПЛУАТАЦІЇ 94

1
2
3
1
1
2
1
1
1
2
1
AB
1
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
Fig.7
Fig.8
2

12
3
1
1
2
1
2
3
1
2
3
Fig.9
Fig.10
Fig.11
Fig.12
Fig.13
Fig.14
Fig.15
3

4ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model DTP131 DTP141
Impact driver mode Fastening
Capacities
Machine screw 4 mm - 8 mm
Standard bolt 5 mm - 14 mm
High tensile bolt 5 mm - 12 mm
No load speed (min-1) (Soft / Medium / Hard) 0 - 1,400 / 0 - 2,200 / 0 - 2,800 0 - 1,300 / 0 - 2,200 / 0 - 2,700
Impacts per minute (Soft / Medium / Hard) 0 - 1,200 / 0 - 2,400 / 0 - 3,200
Hammer drill mode No load speed (min-1)
(Low (1) / High (2))
0 - 700 / 0 - 2,800 0 - 700 / 0 - 2,700
Blows per minute (min-1)
(Low (1) / High (2))
0 - 8,400 / 0 - 32,400
Drilling Capacities / Concrete 8 mm
Drill mode Drilling Capacities
(Low (1) / High (2))
Steel 10 mm / 6.5 mm
Wood 21 mm / 12 mm
No load speed (min-1) 0 - 700 / 0 - 2,800 0 - 700 / 0 - 2,700
Screwdriver mode Fastening
Capacities
(Low (1) / High (2))
Machine screw 3.5 mm - 6 mm / 4 mm - 6 mm
Self drilling screw 4 mm, 5 mm / 4 mm (Thickness 3.2 mm max.)
No load speed (min-1) 0 - 300 / 0 - 1,100 (depends on torque setting)
0 - 600 / 0 - 2,300 (P mode)
Net weight 1.5 - 1.7 kg 1.5 - 1.9 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsmaydifferfromcountrytocountry.
• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Batterycartridge D.C.14.4 V Model BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
D.C.18 V Model BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof
residence.
WARNING: Only use the battery cartridges and chargers listed above.Useofanyotherbatterycartridges
andchargersmaycauseinjuryand/orre.
Intended use
The tool is intended for impact screw driving in wood
and for impact drilling in brick, concrete and stone as
well as for drilling and screw driving without impact in
wood, metal, ceramic and plastic.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ing to EN62841:
Model DTP131
Sound pressure level (LpA) : 85 dB (A)
Sound power level (LWA) : 96 dB (A)
Uncertainty(K):3dB(A)
Model DTP141
Sound pressure level (LpA) : 85 dB (A)
Sound power level (LWA) : 96 dB (A)
Uncertainty(K):3dB(A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DTP131
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 13.0 m/s2
Uncertainty(K):1.5m/s2
Work mode : impact tightening of fasteners of the
maximumcapacityofthetool
Vibration emission (ah) : 8.5 m/s2
Uncertainty(K):2.0m/s2
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2or less
Uncertainty(K):1.5m/s2

5ENGLISH
Model DTP141
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 13.0 m/s2
Uncertainty(K):1.5m/s2
Work mode : impact tightening of fasteners of the
maximumcapacityofthetool
Vibration emission (ah) : 10.5 m/s2
Uncertainty(K):1.5m/s2
Work mode: drilling into metal
Vibration emission (ah,D) : 2.5 m/s2or less
Uncertainty(K):1.5m/s2
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
methodandmaybeusedforcomparingonetoolwith
another.
NOTE:
Thedeclaredvibrationemissionvaluemay
alsobeusedinapreliminaryassessmentofexposure.
WARNING: The vibration emission during actual
use of the power tool can differ from the declared
emissionvaluedependingonthewaysinwhichthe
tool is used.
WARNING:Besuretoidentifysafetymeasures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
accountofallpartsoftheoperatingcyclesuchas
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
TheECdeclarationofconformityisincludedasAnnexA
to this instruction manual.
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listedbelowmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
Cordless 4 Mode Impact Driver
Safety Warnings
1. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool.Lossofcontrolcancausepersonalinjury.
3. Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fastenerscontactinga"live"wiremaymake
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring.Cuttingaccessorycontactinga"live"
wiremaymakeexposedmetalpartsofthepower
tool "live" and could give the operator an electric
shock.
5. Always be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
6. Hold the tool rmly.
7. Keep hands away from rotating parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
10. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
11. Always secure workpiece in a vise or similar
hold-down device.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).

6ENGLISH
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tape or mask off open contacts and pack up the
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliantproductsmayresultinare,exces-
siveheat,explosion,orleakofelectrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
alsovoidtheMakitawarrantyfortheMakitatooland
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeadjust-
ing or checking function on the tool.
Installing or removing battery cartridge
►Fig.1: 1. Red indicator 2. Button 3.Batterycartridge
CAUTION:
• Alwaysswitchoffthetoolbeforeinstallingor
removingofthebatterycartridge.
• Hold the tool and the battery cartridge rmly
when installing or removing battery car-
tridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipoffyour
hands and result in damage to the tool and
batterycartridgeandapersonalinjury.
Toremovethebatterycartridge,slideitfromthetool
while sliding the button on the front of the cartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoronthe
uppersideofthebutton,itisnotlockedcompletely.
CAUTION:
• Alwaysinstallthebatterycartridgefullyuntilthe
redindicatorcannotbeseen.Ifnot,itmayacci-
dentallyfalloutofthetool,causinginjurytoyou
orsomeonearoundyou.
• Donotinstallthebatterycartridgeforcibly.Ifthe
cartridgedoesnotslideineasily,itisnotbeing
insertedcorrectly.
Battery protection system (Lithium-
ion battery with star marking)
►Fig.2: 1. Star marking
Lithium-ion batteries with a star marking are equipped
withaprotectionsystem.Thissystemautomatically
cutsoffpowertothetooltoextendbatterylife.
Thetoolwillautomaticallystopduringoperationifthe
tooland/orbatteryareplacedunderoneofthefollowing
conditions:
• Overloaded:
The tool is operated in a manner that causes
ittodrawanabnormallyhighcurrent.
In this situation, release the trigger switch on
the tool and stop the application that caused
the tool to become overloaded. Then pull the
trigger switch again to restart.
Ifthetooldoesnotstart,thebatteryisover-
heated.Inthissituation,letthebatterycool
before pulling the trigger switch again.
• Lowbatteryvoltage:
Theremainingbatterycapacityistoolow
and the tool will not operate. In this situation,
removeandrechargethebattery.

7ENGLISH
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
►Fig.3: 1. Indicator lamps 2. Check button
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
mayhave
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Switch action
►Fig.4: 1. Switch trigger
CAUTION:
• Beforeinstallingthebatterycartridgeintothe
tool,alwayschecktoseethattheswitchtrigger
actuatesproperlyandreturnstothe"OFF"
position when released.
Tostartthetool,simplypulltheswitchtrigger.Thetool
speedisincreasedbyincreasingpressureontheswitch
trigger. Release the switch trigger to stop.
NOTE:
• The tool will stop three minutes after pulling the
switch trigger.
Lighting up the front lamp
CAUTION:
• Do not look in the lamp or see the source of
lampdirectly.
►Fig.5: 1. Lamp
►Fig.6: 1.LEDdisplay2. Lamp button
Everytimethelampbutton ontheLEDdisplayis
pressed,thelampstatusisalternativelychangedfrom
the ON to the OFF and from the OFF to the ON.
With the lamp button in the ON status, pull the switch trig-
ger to turn on the lamp. To turn off, release it and the lamp
goesoutapproximately10secondsafterreleasing.
With the lamp button in the OFF status, even if the
trigger is pulled, the lamp will not light on.
NOTE:
• To make sure the status of lamp, pull the trigger.
Whenthelamplightsupbypullingtheswitch
trigger, the lamp switch is in the ON status.
When the lamp does not come on, the lamp
switch is in the OFF status.
• During the operation of switch trigger, the lamp
status cannot be changed.
• Forapproximately10secondsafterreleas-
ing the switch trigger, the lamp status can be
switched.
Reversing switch action
►Fig.7: 1. Reversing switch lever
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
CAUTION:
• Alwayscheckthedirectionofrotationbefore
operation.
• Usethereversingswitchonlyafterthetool
comes to a complete stop. Changing the direc-
tionofrotationbeforethetoolstopsmaydam-
age the tool.
• Whennotoperatingthetool,alwayssetthe
reversing switch lever to the neutral position.
Speed change
►Fig.8: 1. Speed change lever
NOTICE:
•
Alwayssetthespeedchangeleverfullytothecor-
rectposition.Ifyouoperatethetoolwiththespeed
changeleverpositionedhalfwaybetweenthe"1"
sideand"2"side,thetoolmaybedamaged.
• Do not use the speed change lever while the
toolisrunning.Thetoolmaybedamaged.
• Do not force the lever to "1" side with impact
drivermode.Thetoolmaybedamaged.
Tochangethespeed,rstswitchoffthetoolandthen
slide the speed change lever to the "2" side for high
speed or "1" side for low speed. Be sure that the speed
change lever is set to the correct position before opera-
tion.Usetherightspeedforyourjob.
When turning the action mode changing ring to impact
driver mode, set the speed change lever to the "2" side.
Selecting the action mode
►Fig.9: 1. Mode mark 2. Action mode changing ring
3. Arrow
Thistoolemploysanactionmodechangingring.Selectoneof
the4modessuitableforyourworkneedbyturningthisring.
When driving wood screws or bolts, point the arrow at
the mark for impact driver mode. The impact force
canbeadjustedontheLEDdisplay.

8ENGLISH
When drilling into concrete or tiles, point the arrow at
the mark for hammer drill mode.
When drilling into wood or metal, point the arrow at
the mark for drill mode.
When driving small wood screws or machine screws,
point the arrow at the mark for screwdriver mode.
ThefasteningtorquecanbeadjustedontheLED
display.
CAUTION:
• Alwayssetthearrowcorrectlytoeithermode
mark.Ifyouoperatethetoolwiththeaction
modechangingringpositionedhalfwaybetween
themodemarks,thetoolmaybedamaged.
• When turning the action mode changing ring,
make sure that the tool stops. If the ring does
noteasilymove,pulltheswitchtriggerslightlyto
rotate the spindle and then move the ring.
•
In the hammer drill mode or drill mode, the blow-
ingforceortorqueisnotadjustable.Inthose
modes,thenumberontheLEDdisplaywillbeoff.
Changing the impact force (impact driver mode)
1
2
3
4
5
1. Changed in three steps 2. Hard 3. Medium 4. Soft 5. Control button
Impact force grade
displayed on panel
Maximum blows
Application Work
Hard
Medium
Soft
Tightening when force
and speed are desired.
Tightening when a good
finishing is needed.
Tightening when excessive
tightening need to be avoided
because of potentially clogged
female screw and broken or
damaged screw head.
Tightening in underwork
material/ Tightening long
screws/ Tightening bolts.
Tightening in the finishing
board, plaster board.
Tightening sash screw/
Tightening small screws
such as M6.
3,200
(min )
-1
DTP131 DTP141
3,200
(min )
-1
2,400
(min )
-1
2,400
(min )
-1
1,200
(min )
-1
1,200
(min )
-1
The impact force can be changed in three steps: hard, medium and soft.
This allows a tightening suitable to the work.
Everytimethebutton is pressed, the impact force grade changes in three steps.
Forapproximatelyoneminuteafterreleasingtheswitchtrigger,theimpactforcecanbechanged.

9ENGLISH
NOTE: During the operation of switch trigger, the impact force grade cannot be changed.
Changing the torque setting
(screwdriver mode)
Thefasteningtorquecanbeadjustedbypressingthe
button in screwdriver mode.
ThenumbersontheLEDdisplayshowstorquesetting.
The fastening torque is minimum at the number 1 and
maximum at the number 9. The indication "P" is a spe-
cial mode for fastening self drilling screws.
Everytimethebutton is pressed, the torque setting
changes from 1 to 9 and P, and then returns to 1.
Thetorquesettingchangesfastbykeepingpressing
the button.
P mode is suitable for fastening self drilling screws into
steel plates in the following conditions.
• With speed change lever at "2" side, fastening
max. 4 mm screw into total max. 3.2 mm steel
plates.
• With speed change lever at "1" side, fastening
max. 5 mm screw.
Before an actual operation, drive a trial screw into
yourmaterialorapieceofduplicatematerialtodeter-
mine which torque level is required for a particular
application.
First,trytofastenthescrewat"1".Thenincreasethe
numbertocontinuefastening.Holdthetoolrmlyduring
operation.
CAUTION: Don't fasten the machine screw on P
mode.Itmaytwistyourwristsuddenlyandresultin
personalinjury.
NOTE:
• MakesuretocheckthenumberonLEDdisplay
before operation. If the number is not indicated,
contactyournearestMakitaservicecenter.
• Whentheremainingbatterycapacitygetslow
inthescrewdrivermode,thelightashesafew
timeswhenfasteningthescrewcompletely.In
thiscase,rechargethebattery.Ifyoukeepoper-
ating,youmaynotobtainthedesiredtorque.
• During pulling the switch trigger, the torque
setting cannot be changed.
• Forapproximatelyoneminuteafterreleasing
the switch trigger, the torque setting can be
changed.ifyouwanttochangethetorqueset-
ting after that, pull the switch trigger again.
• The number of torque setting does not mean
specictorquerate.
Empty signal for remaining battery
capacity
(Countryspecic)
►Fig.10: 1.Batterycapacity
Theremainingbatterycapacitywillbesignaledonthe
LEDdisplaywhenpullingtheswitchtrigger.
Theremainingbatterycapacityisshownasthefollow-
ing table.
LED indicator status Remaining battery capacity
About 50% or more
About 20% - 50%
About less than 20%
NOTE:
•
WhentheLEDdisplaygoesoff,thetoolisturned
offtosavethebatterypower.Tochecktheremain-
ingbatterycapacity,slightlypulltheswitchtrigger.
• TheLEDdisplaygoesoffapproximatelyone
minute after releasing the switch trigger.
•
Whenthetemperatureofthetoolgetshigh,thelightashes
oncepersecondforoneminute,andthentheLEDdisplay
goes off. In this case, cool down the tool before operation.
ASSEMBLY
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforecarrying
outanyworkonthetool.
Installing or removing driver/drill/
socket bit
►Fig.11
Useonlythedriver/drill/socketbitshowninthegure.
Donotuseanyotherdriver/drill/socketbit.
For tool with shallow bit hole
A=12 mm
B=9 mm
Use only these type of bit. Follow the
procedure (1).
(Note) Bit-piece is not necessary.
For tool with deep bit hole
To install these types of bits, follow
the procedure (1).
To install these types of bits, follow
the procedure (2).
(Note) Bit-piece is necessary for
installing the bit.
A=17 mm
B=14 mm
A=12 mm
B=9 mm

10 ENGLISH
1. To install the bit, pull the sleeve and insert the bit
into the sleeve as far as it will go. Then release the
sleeve to secure the bit.
►Fig.12: 1. Bit 2. Sleeve
2. To install the bit, insert the bit-piece and bit into the
sleeve as far as it will go. The bit-piece should be
inserted into the sleeve with its pointed end facing
in. Then release the sleeve to secure the bit.
►Fig.13: 1. Bit 2. Bit-piece 3. Sleeve
To remove the bit, pull the sleeve in the direction of the
arrowandpullthebitoutrmly.
CAUTION:
• Donottouchthedrillbitshortlyafteroperating
as it gets hot. Replace the drill bit after cooling it
down.
NOTE:
• If the bit is not inserted deep enough into the
sleeve, the sleeve will not return to its original
position and the bit will not be secured. In this
case,tryre-insertingthebitaccordingtothe
instructions above.
• Afterinsertingthebit,makesurethatitisrmly
secured. If it comes out, do not use it.
Hook (Optional accessory)
►Fig.14: 1. Groove 2. Hook 3. Screw
CAUTION:
• When installing the hook, tighten the screw
rmly.Failuretodosomaycausethebreakage
ofthetoolorpersonalinjury.
Thehookisconvenientfortemporarilyhangingthetool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
OPERATION
►Fig.15
CAUTION:
• Alwaysinsertthebatterycartridgealltheway
untilitlocksinplacewithalittleclick.Ifyoucan
see the red indicator on the upper side of the
button,itisnotlockedcompletely.Installitfully
until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causing
injurytoyouorsomeonearoundyou.
• Ifthetoolisoperatedcontinuouslyuntilthe
batterycartridgehasdischarged,allowthetool
to rest for 15 minutes before proceeding with a
freshbattery.
Impact driver mode
CAUTION:
• When changing the action mode to the
impact driver mode, always check that the
tool impacts by tightening wood screws. If
theactionmodeisnotchangedcompletely,the
tooltwiststheoperator'shandresultinginjury.
Screwdriving
Holdthetoolrmlyandplacethepointofthedriverbit
inthescrewhead.Applyforwardpressuretothetoolto
the extent that the bit will not slip off the screw and turn
the tool on to start operation.
Tightening bolts
Theproperfasteningtorquemaydifferdependingupon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
teningtorqueandfasteningtimeisshowninthegures.
120
100
80
60
40
20
Standard bolt
N m
Fastening torque
Fastening time
Proper fastening torque
(kgf cm)
(1,224)
(1,020)
(816)
(612)
(408)
(204)
(S)
0 1.0 2.0 3.0
(M14)
(M12)
(M10)
(M8)
0
M14
M12
M10
M8

11 ENGLISH
120
100
80
60
40
20
High tensile bolt
N m
Fastening torque
Fastening time
Proper fastening torque
(kgf cm)
(1,224)
(1,020)
(816)
(612)
(408)
(204)
(S)
0 1.0 2.0 3.0
(M12)
(M10)
(M8)
0
M12
M10
M8
NOTE:
• When the action mode is set to impact driver
mode,makesurethatthetoolimpactsproperly
byfasteningawoodscrewbeforeoperation.
Ifthetooldoesnotworkproperly,contactyour
nearest Makita service center.
• Hold the tool pointed straight at the screw.
• Use the proper bit for the head of the screw/bolt
thatyouwishtouse.
• WhenfasteningscrewM8orsmaller,carefully
adjustpressureontheswitchtriggersothatthe
screw is not damaged.
• Ifyoutightenthescrewforatimelongerthan
showninthegures,thescreworthepointof
thedriverbitmaybeoverstressed,stripped,
damaged,etc.Beforestartingyourjob,always
perform a test operation to determine the proper
fasteningtimeforyourscrew.
Thefasteningtorqueisaffectedbyawidevarietyof
factorsincludingthefollowing.Afterfastening,always
check the torque with a torque wrench.
1. Whenthebatterycartridgeisdischargedalmost
completely,voltagewilldropandthefastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.
3. Bolt
• Eventhoughthetorquecoefcientandthe
class of bolt are the same, the proper fasten-
ing torque will differ according to the diame-
ter of bolt.
• Even though the diameters of bolts are the
same, the proper fastening torque will differ
accordingtothetorquecoefcient,theclass
of bolt and the bolt length.
4. The manner of holding the tool or the material
of driving position to be fastened will affect the
torque.
5. Operating the tool at low speed will cause a reduc-
tion in the fastening torque.
Hammer drill mode
CAUTION:
• Alwaysholdthetoolrmlyduringoperation.
There is a tremendous and sudden twisting
force exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips and particles, or when striking rein-
forcing rods embedded in the concrete.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light pres-
suregivesbestresults.Keepthetoolinpositionand
preventitfromslippingawayfromthehole.
Donotapplymorepressurewhentheholebecomes
clogged with chips or particles. Instead, run the tool at
anidle,thenremovethebitpartiallyfromthehole.By
repeating this several times, the hole will be cleaned out
andnormaldrillingmayberesumed.
Drilling mode
CAUTION:
• Pressingexcessivelyonthetoolwillnotspeed
up the drilling. In fact, this excessive pressure
willonlyservetodamagethetipofyourbit,
decrease the tool performance and shorten the
service life of the tool.
• There is a tremendous force exerted on the tool/
bit at the time of hole break through. Hold the
toolrmlyandexertcarewhenthebitbeginsto
break through the workpiece.
• Astuckbitcanberemovedsimplybysetting
the reversing switch to reverse rotation in order
tobackout.However,thetoolmaybackout
abruptlyifyoudonotholditrmly.
• Alwayssecuresmallworkpiecesinaviseor
similar hold-down device.
• Donotpulltheswitchtriggerrepeatedlywhen
themotorislocked.Itmaydamagethetool.
For drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screwmakesdrillingeasierbypullingthebitintothe
workpiece.
For drilling in metal, to prevent the bit from slipping
when starting a hole, make an indentation with a cen-
ter-punch and hammer at the point to be drilled. Place
the point of the bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tionsareironandbrasswhichshouldbedrilleddry.
NOTE:
• Choose suitable speed for the work load. Drilling
overthefollowingcapacitymaydamagethe
tool.

12 ENGLISH
Drilling capacity
High speed
Low speed
Steel 6.5 mm
Steel
Wood
Wood
12 mm
10 mm
21 mm
Screwdriver mode
CAUTION:
• AdjustthenumberontheLEDdisplaytothe
propertorquelevelforyourwork.
• Make sure that the driver bit is inserted straight
inthescrewhead,orthescrewand/orbitmay
be damaged.
• Holdthetoolrmly.Whentheclutchcutsinor
refastening,asuddentwistingforcemayoccur
anditcantwistyourwrist.
Place the point of the driver bit in the screw head and
applypressuretothetool.Startthetoolslowlyandthen
increasethespeedgradually.
NOTE:
• Thistoolemploysanelectronicclutch.Thetool
stopsautomaticallywhentheclutchcutsin.To
keep operating, release the switch trigger once.
• When driving wood screws, predrill pilot holes
to make driving easier and to prevent splitting of
the workpiece. See the chart.
Nominal diameter of wood screw
(mm)
Recommended size of pilot hole
(mm)
3.
12
.0 - 2.2
3.
52
.2 - 2.5
3.
82
.5 - 2.8
4.
52
.9 - 3.2
4.
83
.1 - 3.4
5.
13
.3 - 3.6
5.
53
.7 - 3.9
5.
84
.0 - 4.2
6.
14
.2 - 4.4
NOTE:
• See the following chart for the relation between
the number of torque setting and fastening
torque rate.
The fastening torque rate will be different
depends on materials. Make a test fastening to
get the desired torque before operation.
Fastening torque rate
Number
on LED
Display
1
3
5
7
9
Low (1) High (2)
Approx. 2.5 N m
(Approx. 25.5 kgf. cm)
Approx. 4.6 N m
(Approx. 46.9 kgf. cm)
Approx. 8.1 N m
(Approx. 82.6 kgf. cm)
Approx. 10.0 N m
(Approx. 102.0 kgf. cm)
Approx. 11.5 N m
(Approx. 117.3 kgf. cm)
Approx. 1.1 N m
(Approx. 11.2 kgf. cm)
Approx. 2.0 N m
(Approx. 20.4 kgf. cm)
Approx. 3.0 N m
(Approx. 30.6 kgf. cm)
Approx. 4.0 N m
(Approx. 40.8 kgf. cm)
Approx. 5.8 N m
(Approx. 59.1 kgf. cm)
.
.
.
.
.
.
.
.
.
.
MAINTENANCE
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeattempt-
ing to perform inspection or maintenance except
for the following troubleshooting related to the
light.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
mayresult.
To maintain product SAFETY and RELIABILITY, repairs,
anyothermaintenanceoradjustmentshouldbeper-
formedbyMakitaAuthorizedServiceCenters,always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mendedforusewithyourMakitatoolspecied
inthismanual.Theuseofanyotheraccessories
orattachmentsmightpresentariskofinjuryto
persons.Onlyuseaccessoryorattachmentfor
its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ingtheseaccessories,askyourlocalMakitaService
Center.
• Screw bits
• Hook
• Plasticcarryingcase
• Makitagenuinebatteryandcharger
NOTE:
• Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.They
maydifferfromcountrytocountry.

13 SLOVENŠČINA
SLOVENŠČINA (Originalna navodila)
TEHNIČNI PODATKI
Model DTP131 DTP141
Načinudarnega
vijačnika
Zmogljivosti
zategovanja
Strojnivijak 4 mm - 8 mm
Standardnivijak 5 mm - 14 mm
Visokonateznivijak 5 mm - 12 mm
Hitrost brez obremenitve (min-1)
(Mehko/Srednja/Trdo)
0 - 1.400 / 0 - 2.200 / 0 - 2.800 0 - 1.300 / 0 - 2.200 / 0 - 2.700
Impactsperminute(Mehko/Srednja/Trdo) 0 - 1.200 / 0 - 2.400 / 0 - 3.200
Načinudarnega
vrtanja
Hitrost brez obremenitve (min-1)
(Nizko (1) / Visoko (2))
0 - 700 / 0 - 2.800 0 - 700 / 0 - 2.700
Udarci na minuto (min-1)
(Nizko (1) / Visoko (2))
0 - 8.400 / 0 - 32.400
Zmogljivostivrtanjavbeton 8 mm
Načinvrtanja Zmogljivostivrtanja
(Nizko (1) / Visoko (2))
Jeklo 10 mm / 6,5 mm
Les 21 mm / 12 mm
Hitrost brez obre-
menitve (min-1)
0 - 700 / 0 - 2.800 0 - 700 / 0 - 2.700
Načinvijačnika Zmogljivosti
zategovanja
(Nizko (1) / Visoko (2))
Strojnivijak 3,5 mm - 6 mm / 4 mm - 6 mm
Samoreznivijak 4mm,5mm/4mm(debelinanajveč3,2mm)
Hitrost brez obre-
menitve (min-1)
0 - 300 / 0 - 1.100 (odvisno od nastavitve navora)
0-600/0-2.300(načinP)
Netoteža 1,5 - 1,7 kg 1,5 - 1,9 kg
Nazivna napetost D.C. 14,4 V D.C. 18 V
• Kernenehnoopravljamoraziskaveinrazvijamosvojeizdelke,selahkotehničnipodatkivtemdokumentu
spremenijobrezobvestila.
• Tehničnipodatkiselahkorazlikujejooddržavedodržave.
• Težaselahkorazlikujegledenapriključke,vključnozakumulatorskobaterijo.Najlažjainnajtežjakombinacijav
skladu s postopkom EPTA 01/2014 sta prikazani v preglednici.
Uporabna akumulatorska baterija in polnilnik
Baterijskivložek Model D.C. 14,4 V BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
Model D.C. 18 V BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
Polnilnik DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
• Nekaterezgorajnavedeneakumulatorskebaterijeinpolnilnikimordavvašidržaviprebivališčanisonavoljo.
OPOZORILO: Uporabljajte le zgoraj navedene akumulatorske baterije in polnilnike. Uporaba drugih
akumulatorskihbaterijinpolnilnikovlahkopovzročitelesnepoškodbein/alipožar.
Predvidena uporaba
Orodjeseuporabljazaudarnovijačenjevijakovvlesin
zaudarnovrtanjevopeke,betoningradbenikamen,
obenempatudizavrtanjeinvijačenjevijakovvles,
kovino, keramiko in plastiko brez udarcev.
Hrup
Tipični,zAocenjenivrednostihrupagledenaEN62841:
Model DTP131
Ravenzvočnegatlaka(LpA): 85 dB (A)
Ravenzvočnemoči(LWA): 96 dB (A)
Odstopanje(K):3dB(A)
Model DTP141
Ravenzvočnegatlaka(LpA): 85 dB (A)
Ravenzvočnemoči(LWA): 96 dB (A)
Odstopanje(K):3dB(A)
Uporabljajte zaščito za sluh
Vibracije
Skupnevrednostivibracij(vektorskavsotatrehosi)poEN62841:
Model DTP131
Delovninačin:udarnovrtanjevbeton
Oddajanjetresljajev(ah,ID): 13,0 m/s2
Odstopanje(K):1,5m/s2
Delovninačin:udarnoprivijanjepritrjevalnikovz
največjozmogljivostjoorodja
Oddajanjetresljajev(ah): 8,5 m/s2
Odstopanje(K):2,0m/s2
Delovninačin:vrtanjevkovino
Oddajanjetresljajev(ah,D): 2,5 m/s2alimanj
Odstopanje(K):1,5m/s2

14 SLOVENŠČINA
Model DTP141
Delovninačin:udarnovrtanjevbeton
Oddajanjetresljajev(ah,ID): 13,0 m/s2
Odstopanje(K):1,5m/s2
Delovninačin:udarnoprivijanjepritrjevalnikovz
največjozmogljivostjoorodja
Oddajanjetresljajev(ah): 10,5 m/s2
Odstopanje(K):1,5m/s2
Delovninačin:vrtanjevkovino
Oddajanjetresljajev(ah,D): 2,5 m/s2alimanj
Odstopanje(K):1,5m/s2
OPOMBA:Navedenavrednostoddajanjavibracij
jebilaizmerjenavskladusstandardnimimetodami
testiranjainselahkouporabljazaprimerjavoorodij.
OPOMBA:Navedenavrednostoddajanjavibra-
cijselahkouporabljatudipripredhodnioceni
izpostavljenosti.
OPOZORILO:Oddajanjevibracijmeddejansko
uporaboelektričnegaorodjaselahkorazlikujeod
navedenevrednostioddajanja,odvisnoodnačina
uporabeorodja.
OPOZORILO:Upravljavecmorazalastnozaš-
čitopoznativarnostneukrepe,kitemeljijonaoceni
izpostavljenostivdejanskihpogojihuporabe(upošte-
vajočcelotendelovniprocesvtrenutkih,kojeorodje
izključenoinkodelujevprostemtekuzdodatkom
časasprožitve).
Izjava o skladnosti ES
Samo za evropske države
IzjavaESoskladnostijevključenavdodatkuA,kije
priložentemnavodilomzauporabo.
Splošna varnostna opozorila za
električno orodje
OPOZORILO: Preberite vsa varnostna opo-
zorila in navodila s slikami in tehničnimi podatki,
ki so dobavljeni skupaj z električnim orodjem.
Obneupoštevanjuspodajnavedenihnavodilobstaja
nevarnostelektričnegaudara,požarain/alihudih
telesnihpoškodb.
Shranite vsa opozorila in navo-
dila za poznejšo uporabo.
Izraz„električnoorodje“vopozorilihsenanašanavaše
električnoorodje(skablom)alibaterijskoelektrično
orodje(brezkabla).
Varnostna opozorila za
akumulatorski udarni vijačnik s 4
načini
1. Pri udarnem vrtanju nosite zaščito za sluh.
Izpostavljenosthrupulahkopovzročiizgubosluha.
2. Uporabite pomožne ročaje, če so dobavljeni
z orodjem.Izgubanadzoralahkopovzroči
poškodbeoseb.
3. Če obstaja nevarnost, da bi s pritrjevalnikom
prerezali skrito električno napeljavo, držite ele-
ktrično orodje na izoliranih držalnih površinah.
Obstikuzvodnikipodnapetostjodobijonapetost
vsineizoliranikovinskidelielektričnegaorodja,
zaradičesarlahkopridedoelektričnegaudara.
4. Če obstaja nevarnost, da bi z rezilnim orodjem
prerezali skrito električno napeljavo, držite ele-
ktrično orodje na izoliranih držalnih površinah.
Obstikuzvodnikipodnapetostjodobijonapetost
vsineizoliranikovinskidelielektričnegaorodja,
zaradičesarlahkouporabnikutrpielektričniudar.
5. Vedno zagotovite, da imate trden oprijem na
podlagi, kjer stojite.
Kadar uporabljate orodje na višini, se prepri-
čajte, da spodaj ni nikogar.
6. Trdno držite orodje.
7. Ne približujte rok vrtečim se delom.
8. Orodja ne pustite delovati brez nadzora.
Dovoljeno ga je uporabljati samo ročno.
9. Takoj po končani obdelavi se ne dotikajte
nastavka ali obdelovanca; lahko sta zelo vroča
in povzročita opekline kože.
10. Nekateri materiali vsebujejo kemikalije, ki so
lahko strupene. Bodite previdni in preprečite
vdihavanje prahu in stik s kožo. Upoštevajte
varnostne podatke dobavitelja materiala.
11. Obdelovanec vedno vpnite v primež ali
podobno napravo za držanje.
SHRANITE TA NAVODILA.
OPOZORILO: NE dovolite, da bi zaradi udob-
nejšega dela ali znanja o uporabi izdelka (prido-
bljenega z večkratno uporabo) opustili strogo
upoštevanje varnostnih zahtev v okviru pravilne
uporabe orodja.
ZLORABA ali neupoštevanje varnostnih zahtev
v teh navodilih za uporabo lahko povzroči resne
telesne poškodbe.
Pomembna varnostna navodila za
akumulatorsko baterijo
1. Pred uporabo baterijskega vložka preberite
vsa navodila in opozorilne oznake na (1) pol-
nilniku akumulatorja, (2) akumulatorju in (3)
izdelku, ki uporablja akumulator.
2. Ne razstavljajte baterijskega vložka.
3. Če se je čas delovanja občutno skrajšal, takoj
prenehajte uporabljati orodje. V nasprotnem
primeru lahko pride do pregretja, morebitnih
opeklin in celo eksplozije.
4. Če pride elektrolit v stik z očmi, jih sperite s
čisto vodo in takoj poiščite zdravniško pomoč.
Posledica je lahko izguba vida.
5.
Ne povzročite kratkega stika baterijskega vložka:
(1) Ne dotikajte se priključkov s kakršnim
koli prevodnim materialom.
(2) Izogibajte se shranjevanju baterijskega
vložka v vsebniku z drugimi kovinskimi
predmeti kot so žeblji, kovanci itn.
(3) Ne izpostavljajte baterijskega vložka vodi
ali dežju.

15 SLOVENŠČINA
Kratek stik akumulatorja lahko povzroči velik
električni tok, pregrevanje, morebitne opekline
in celo okvaro.
6. Ne shranjujte orodja in baterijskega vložka
na mestih, kjer lahko temperatura doseže ali
preseže 50 °C.
7. Ne sežigajte baterijskega vložka, tudi če je
hudo poškodovan ali v celoti izpraznjen.
Baterijski vložek lahko v ognju eksplodira.
8. Poskrbite, da akumulator ne bo izpostavljen
padcem ali udarcem.
9. Ne uporabljajte poškodovanih akumulatorjev.
10. Priložene litij-ionske baterije ustrezajo zahte-
vam zakonodaje v zvezi z nevarnim blagom.
Zakomercialneprevoze,npr.tiste,kijihopravljajo
tretjestrankeincarinskiposredniki,jetrebaupo-
števatiposebnezahtevevzvezizembalažoin
označevanjem.
Med postopkom priprave na odpremo izdelka se
jetrebaposvetovatisstrokovnjakomzanevarne
snovi.Pritemupoštevajtetudipodrobnejšenacio-
nalne predpise.
Odprtestikeoblepitezlepilnimtrakomalijihdru-
gačezaščitite,baterijopazapakirajtetako,dasev
embalažinemorepremikati.
11. Upoštevajte lokalne uredbe glede odlaganja
akumulatorja.
12. Baterije uporabljajte le z izdelki, ki jih določi
Makita.Čenamestitebaterijevneskladneizdelke,
lahkopridedopožara,pregrevanja,eksplozijeali
puščanjaelektrolita.
SHRANITE TA NAVODILA.
POZOR: Uporabljajte le originalne baterije
Makita.ČeuporabljateneoriginalnebaterijeMakita
alibaterije,kisobilespremenjene,lahkopridedo
eksplozijebaterijeinposledičnodopožara,telesnih
poškodbalimaterialneškode.Stakšnouporabo
bostetudirazveljaviligarancijoMakitazaorodjein
polnilnik Makita.
Nasveti za ohranjanje največje
zmogljivosti akumulatorja
1. Napolnite baterijski vložek, preden se v celoti
izprazni. Ko opazite, da ima orodje manjšo
moč, vedno ustavite delovanje orodja in napol-
nite baterijski vložek.
2. Nikoli znova ne polnite popolnoma napol-
njenega baterijskega vložka. Prenapolnjenje
skrajša življenjsko dobo akumulatorja.
3. Baterijski vložek s sobno temperaturo pol-
nite pri temperaturi okolja od 10 °C do 40 °C.
Počakajte, da se vroč baterijski vložek pred
polnjenjem ohladi.
4. Če baterijskega vložka ne uporabljate dalj časa
(več kot 6 mesecev), ga napolnite.
OPIS DELOVANJA
POZOR:
• Predvsakonastavitvijoalipregledomdelovanja
orodjaseprepričajte,dajeletoizključenoinda
jeakumulatorskabaterijaodstranjena.
Nameščanje ali odstranjevanje
akumulatorske baterije
►Sl.1: 1.Rdečiindikator2. Gumb 3.Baterijskivložek
POZOR:
• Vednoizklopiteorodje,predennamestiteali
odstraniteakumulatorskobaterijo.
• Kadar nameščate ali odstranjujete akumula-
torsko baterijo, trdno držite orodje in akumu-
latorsko baterijo.Čeorodjainakumulatorske
baterijenedržitetrdno,selahkozgodi,davam
zdrsnetaizrok,posledicapajepoškodbaorodja
inakumulatorskebaterijetertelesnapoškodba.
Zaodstranitevakumulatorskebaterijeizorodjajo
premakniteizorodja,obtempapremaknitegumbna
sprednjistraniakumulatorskebaterije.
Privstavljanjuakumulatorskebaterijeporavnajtejezi-
čeknaakumulatorskibaterijizutoromnaohišjuinga
potisnitevležišče.Akumulatorskobaterijovstavitedo
konca,daserazločnozaskoči.Čeviditerdečiindikator
nazgornjistranigumba,tanipopolnomazaklenjen.
POZOR:
•
Vednonamestiteakumulatorskobaterijo,takoda
rdečiindikatornivečviden.Četeganeupoštevate,
lahkoakumulatornepričakovanoizpadeizorodjain
poškodujevasaliosebevneposrednibližini.
• Nenameščajteakumulatorskebaterijessilo.Če
seakumulatorskabaterijanezaskočizlahka,ni
pravilnovstavljena.
Sistem za zaščito akumulatorja (litij-
ionske akumulatorji z zvezdico)
►Sl.2: 1. Oznaka z zvezdico
Litij-ionskeakumulatorjisoopremljenezzaščitnimsiste-
mom.Tasistemsamodejnoizklopidovajanjeelektrične
energijevorodje,dabipodaljšalživljenjskodobobaterije.
Orodjesebosamodejnozaustavilomeddelovanjem,česta
orodjein/alibaterijazamenjanapodnaslednjimipogoji:
• Preobremenjeno:
Orodjedelujenanačin,kipovzroča,da
povlečenenormalnovisoktok.
Vtemprimerusprostitesprožilnostikalona
orodjuinustaviteuporabo,kipovzročapreo-
bremenjenostorodja.Zaponovnivklopnato
ponovnopovlecitesprožilnostikalo.
Česeorodjenevklopi,jeakumulatorpregret.
V tem primeru pustite, da se akumulator ohladi,
predenponovnopovlečetesprožilnostikalo.
• Nizkanapetostakumulatorja:
Preostalazmogljivostakumulatorjajepre-
nizkainorodjenebodelovalo.Vtempri-
meru odstranite in napolnite akumulator.

16 SLOVENŠČINA
Prikazuje preostalo raven
napolnjenosti akumulatorja
Samo za akumulatorske baterije z indikatorjem
►Sl.3: 1.Indikatorskelučke2.Gumbzapreverjanje
Pritisnitegumbzapreverjanjenabaterijskemvložku,
dapreveriteravennapolnjenostiakumulatorja.
Indikatorskelučkenakratkozasvetijo.
Indikatorske lučke Prikaz pre-
ostale ravni
napolnjenosti
Sveti Ne sveti Utripa
od 75 % do
100 %
od 50 % do
75 %
od 25 % do
50 %
od 0 % do
25 %
Napolnite
akumulator.
Akumulator
jemorda
okvarjen.
OPOMBA:Odvisnoodpogojevuporabeinokoljske
temperatureseoznačbalahkonekolikorazlikujeod
dejanskenapolnjenosti.
Delovanje stikala
►Sl.4: 1.Sprožilnostikalo
POZOR:
• Predennamestiteakumulatorskobaterijov
orodjesevednoprepričajte,dajestikalobrez-
hibnoindasevračavpoložajzaizklop(OFF),
ko ga spustite.
Zazagonorodjapreprostopovlecitesprožilnostikalo.
Hitrostorodjasepoveča,kopovečatepritisknaspro-
žilnostikalo.Zaizkloporodjaspustitesprožilnostikalo.
OPOMBA:
• Orodjaseboustavilotriminutezatem,kopovle-
četesprožilnostikalo.
Vklop sprednje lučke
POZOR:
• Neglejtenaravnostvlučkoaliizvorlučke.
►Sl.5: 1. Svetilka
►Sl.6: 1. LED zaslon 2.Gumblučke
Vsakič,kopritisnetegumblučke na LED zaslonu,
sestanjelučkeizmeničnospreminjaizVKLOPLJENAv
IZKLOPLJENAinobratno.
KojestanjegumbalučkeVKLOPLJENA,povlecite
sprožilnostikalozavkloplučke.Zaizklop,gaizpustite
inlučkabougasnilapribližno10potem,kojospustite.
KojestanjegumbalučkeIZKLOPLJENA,lučkanebo
zasvetila,tudičejesprožilnikpovlečen.
OPOMBA:
• Čeželitepreveritistanjelučke,povlecitesprožil-
nik.Čelučkazasveti,kopovlečetesprožilnosti-
kalo,jestanjelučkeVKLOPLJENA.Čelučkane
zasveti,potemjestanjelučkeIZKLOPLJENA.
• Medpritiskomnasprožilnostikalonimogoče
spreminjatistanjalučke.
• Približno10sekundzatem,kospustitesprožilno
stikalo,lahkopreklopitestanjelučke.
Stikalo za preklop smeri vrtenja
►Sl.7: 1.Preklopnaročicazaobratnosmer
Toorodjejeopremljenospreklopnikomzaspremembo
smerivrtenja.Ročicopreklopnikasmerivrtenjapritisnite
vsmeriAzavrtenjevsmeriurinegakazalcainvsmeri
Bzavrtenjevobratnismeriurinegakazalca.
Kojepreklopnostikalovnevtralnempoložaju,seglav-
nega stikala ne da premakniti.
POZOR:
• Predobratovanjemvednopreveritesmer
vrtenja.
• Stikalozaspreminjanjesmerivrtenjauporabite
šele,kosestrojpopolnomaustavi.Česmer
vrtenjaspremenite,predensestrojustavi,seta
lahkopoškoduje.
• Koorodjaneuporabljate,vednopotisnite
preklopnostikalovnevtralenpoložaj.
Spreminjanje hitrosti
►Sl.8: 1.Ročicazaspremembohitrosti
OBVESTILO:
• Stikalozaspreminjanjehitrostivrtenjavedno
potisnitevkončnipoložaj.Čevklopitestroj,
medtemkojestikalovvmesnempoložajumed
oznakama »1« in »2«, lahko pride do okvare
stroja.
• Stikalazaspreminjanjehitrostivrtenjanepre-
mikajtemeddelovanjemstroja.Strojselahko
poškoduje.
• Nesilitestikalavpoložaj„1“vnačinuudarnega
vijačnika.Orodjeselahkopoškoduje.
Čeželitespremenitihitrostvrtenja,strojnajprejizklopite,
natopastikalozaspreminjanjehitrostivrtenjanastavite
vpoložaj»2«(visokoštevilovrtljajev)alivpoložaj»1«
(nizkoštevilovrtljajev).Predobratovanjempreverite,alije
stikalozaspreminjanjehitrostivrtenjanastavljenovpravi-
lenpoložaj.Hitrostvrtenjaprilagoditezahtevamdela.
Kadarvrtitepreklopniobročzanačindelovanjavnačin
udarnegavijačnika,nastavitestikalozaspreminjanje
hitrostivrtenjavpoložaj„2“.
Izbira načina delovanja
►Sl.9: 1.Oznakanačina2.Obročzaspremembo
načinadelovanja3.Puščica
Orodjejeopremljenospreklopnimobročemzanačin
delovanja.Stemobročemizberiteenegaizmed4nači-
nov,kijeprimerenzavašeopravilo.

17 SLOVENŠČINA
Kadarprivijatelesnealimatičnevijake,nastavite
puščiconaoznako zanačinudarnegavijačnika.
UdarnosilolahkoprilagajatenaLEDzaslonu.
Privrtanjuvbetonalikeramičneploščice,nastavite
puščiconaoznako zanačinudarnegavrtanja.
Privrtanjuvlesalikovino,nastavitepuščicona
oznako zanačinvrtanja.
Kadarprivijatemajhnelesnealistrojnevijake,nastavite
puščiconaoznako zanačinvijačnika.Zatezni
momentlahkoprilagajatenaLEDzaslonu.
POZOR:
•
Puščicovednopravilnonastavitenaizbranooznako
načina.Čebopreklopniobročzanačindelovanja
meddelovanjemvvmesnempoložajumedozna-
kamanačina,lahkopridedookvarestroja.
• Kadarvrtitepreklopniobročzanačindelovanja,se
prepričajte,alijeorodjeustavljeno.Česeobročne
premikapreprosto,rahlopovlecitesprožilnostikalo,
dazavrtitevreteno,innatopremakniteobroč.
• Vnačinuudarnegavrtanjaalinačinuvrtanjanimogoče
prilagajatisilepihanjaalizateznegamomenta.Vteh
načinihboštevilkanaLEDzaslonuizklopljena.
Spreminjanje udarne sile (način udarnega vijačnika)
1
2
3
4
5
1.Spremenjenovtrehkorakih2. Trdo 3.Srednja4. Mehko 5.Upravljalnigumb
Stopnja udarne sile,
prikazana na zaslonu
Največ udarcev
Aplikacija Delo
Trdo
Srednja
Mehko
Privijanje, kadar sta
potrebna moč in hitrost.
Privijanje, kadar je potreben
dober zaključek.
Privijanje, kadar se je treba
izogibati čezmernemu
privijanju zaradi morebiti
zamašenega ženskega dela
vijaka in zlomljene ali
poškodovane glave vijaka.
Privijanje v material podzidja/
Privijanje dolgih vijakov/
Privijanje matičnih vijakov.
Privijanje v zaključne plošče,
plošče iz mavca.
Privijanje vijakov za okenske
okvirje/Privijanje majhnih
vijakov, npr. M6.
3.200
(min )
-1
DTP131 DTP141
3.200
(min )
-1
2.400
(min )
-1
2.400
(min )
-1
1.200
(min )
-1
1.200
(min )
-1
Udarnosilolahkospreminjatevtrehkorakih:močno,srednjeinrahlo.
Toomogočaprivijanje,kijeprimernozadelo.
Vsakič,kopritisnetegumb ,sestopnjaudarnesilespremenivtrehkorakih.
Približnoenominutozatem,kospustitesprožilnostikalo,lahkospremeniteudarnosilo.

18 SLOVENŠČINA
OPOMBA:Medpritiskomnasprožilnostikalonimogočespreminjatistopnjeudarnesile.
Spreminjanje nastavitve zateznega
momenta (način vijačnika)
Zatezni moment lahko prilagodite s pritiskom na
gumb vnačinuvijačnika.
ŠtevilkenaLEDzaslonuprikazujejonastavitevzate-
znegamomenta.Zateznimomentjenajmanjšina
številki1innajvečjinaštevilki9.Oznaka„P“jeposeben
načinzaprivijanjesamoreznihvijakov.
Vsakič,kopritisnetegumb , se nastavitev zateznega
momenta spremeni od 1 do 9 in P, nato pa se vrne na 1.
Nastavitevzateznegamomentasehitrospremeni,če
nenehno pritiskate gumb.
NačinPjeprimerenzaprivijanjesamoreznihvijakovv
jekleneploščepodnaslednjimipogoji.
• Čejestikalozaspreminjanjehitrostivrtenjav
položaju„2“,lahkoprivijatenajveč4-milimetrske
vijakevjekleneploščesskupnodebelino3,2mm.
• Čejestikalozaspreminjanjehitrostivrtenjav
položaju„1“,lahkoprivijatenajveč5-milimetrske
vijake.
Preddejanskouporaboprivijteposkusnivijakvmaterial
ali v podoben kos, da ugotovite, kateri zatezni moment
jepotrebenzadoločenouporabo.
Najprejposkusiteprivitivijakvpoložaju„1“.Natopove-
čajteštevilkoinnadaljujtesprivijanjem.Meddelom
trdnodržiteorodje.
POZOR:StrojnihvijakovneprivijajtevnačinuP.
Nenadomavamlahkozasučezapestjeinpovzroči
telesnopoškodbo.
OPOMBA:
• Predopravilomnepozabitepreveritištevilkena
LEDzaslonu.Češtevilkaniprikazana,stopitev
stikznajbližjimservisnimcentromMakita.
• Kojepreostalazmogljivostakumulatorjav
načinuvijačnikanizka,lučkanekajkratutri-
pnemeddokončnimprivijanjemvijaka.Vtem
primerunapolniteakumulator.Čenadaljujete
zdelom,mogočenebostedosegliželenega
zateznega momenta.
• Medvlečenjemsprožilnegastikalanimogoče
spreminjatinastavitvezateznegamomenta.
• Približnoenominutopotem,kospustitespro-
žilnostikalo,lahkospremenitenastavitevzate-
znegamomenta.Čeželitespremenitinastavitev
zateznega momenta po tem, znova povlecite
sprožilnostikalo.
• Številka nastavitve zateznega momenta ne
pomenidoločenestopnjezateznegamomenta.
Signal za preostalo zmogljivost
akumulatorja
(Odvisnooddržave)
►Sl.10: 1.Zmogljivostakumulatorja
Kopovlečetesprožilnostikalo,boLEDzaslonsporočal
preostalozmogljivostakumulatorja.
Preostalazmogljivostakumulatorjajeprikazanavnas-
lednjitabeli.
Status LED indikatorja
Preostala zmogljivost
akumulatorja
približno 50 % ali več
približno 20 - 50 %
približno manj kot 20 %
OPOMBA:
•
KoLEDzaslonugasne,seorodjeizključi,davarčuje
zakumulatorjem.Čeželitepreveritipreostalozmoglji-
vostakumulatorja,rahlopovlecitesprožilnostikalo.
• Približnoenominutopotem,kospustitespro-
žilnostikalo,LEDzaslonugasne.
•
Čejetemperaturaorodjaprevisoka,lučkautripa
enkrat na sekundo eno minuto, nato pa LED zaslon
ugasne.Vtemprimerupreddelomohladiteorodje.
MONTAŽA
POZOR:
•
Predvsakoizvedbodelanaorodjuseprepričajte,dajele
toizključenoindajeakumulatorskabaterijaodstranjena.
Namestitev ali odstranitev vijačnega
nastavka/svedra/natičnega nastavka
►Sl.11
Uporabljajtelevijačninastavek/sveder/natičninasta-
vek,prikazannasliki.Neuporabljajtedrugihvijačnih
nastavkov/svedrov/natičnihnastavkov.
Za orodje s plitvo odprtino za nastavke
A=12 mm
B=9 mm
Uporabljajte samo te vrste nastavkov.
Sledite postopku (1).
(Opomba) Nastavek ni potreben.
Za orodje z globoko odprtino za nastavke
Za namestitev teh nastavkov
sledite postopku (1).
Za namestitev teh nastavkov sledite
postopku (2).
(Opomba) Za namestitev nastavka je
potreben del nastavka.
A=17 mm
B=14 mm
A=12 mm
B=9 mm

19 SLOVENŠČINA
1. Zanameščanjenastavkapovlecitestročnicoin
vstavitenastavekvstročnicodoomejila.Nato
izpustitestročnicointakoksirajtenastavek.
►Sl.12: 1. Nastavek 2.Vložek
2. Zanameščanjenastavkavstaviteizenačevalno
konicovstročnicodoomejila.Izenačevalnokonico
vstavitevstročnicoskoničastimdelomnaprej.
Natoizpustitestročnicointakoksirajtenastavek.
►Sl.13: 1. Nastavek 2.Izenačevalnakonica3.Vložek
Zaodstranitevnastavkapovlecitestročnicovsmeri
puščiceinnastavekizvlecite.
POZOR:
• Nekajčasapoopravilusenedotikajtesvedra,
sajjevroč.Kosesvederohladi,gazamenjajte.
OPOMBA:
• Čenastavekvstročniconivstavljendovoljglo-
boko,sestročnicanebovrnilavprvotnipoložaj
innastaveknebopravilnoblokiranvsvojem
ležišču.Vtemprimeruposkušajtenastavek
vstavitiznovakotjeopisanozgoraj.
• Konamestitenastavek,seprepričajte,alije
trdnoprivit.Čegalahkoizvlečete,nezačnitez
vijačenjem.
Kavelj (dodatna oprema)
►Sl.14: 1. Utor 2.Kljuka3.Vijak
POZOR:
• Prinameščanjukavljamočnozategnitevijak.
Četeganestorite,lahkopridedookvareorodja
alitelesnepoškodbe.
Kaveljjepriročenpripomočekzazačasnoobešanje
stroja.Namestitegalahkonakaterokolistranstroja.
Kaveljvstavitevutornalevialidesnistraniohišjastroja
ingaprivijtezvijakom.Dagaodstranite,odvijtevijakin
ga izvlecite.
DELOVANJE
►Sl.15
POZOR:
• Akumulatorskobaterijovednovstavitedo
konca,daserazločnozaskoči.Čeviditerdečo
črtonazgornjistranigumba,tanipopolnoma
zaklenjen.Popolnomanamestite,takodardeča
črtanividna.Četeganeupoštevate,lahko
akumulatorskabaterijanepričakovanoizpadeiz
orodjainpoškodujevasaliosebevneposredni
bližini.
• Čeorodjeneprekinjenodeluje,doklerseaku-
mulatorskabaterijaneizprazni,pustiteorodje
15minutmirovatiinšelenatonadaljujteznovo
baterijo.
Način udarnega vijačnika
POZOR:
• Kadar spreminjate način delovanja v način
udarnega vijačnika, vedno preverite, ali
orodje udarja s privijanjem lesnih vijakov.
Čenačindelovanjanipovsempreklopljen,bo
orodjezviloupravljavčevorokoinpovzročilo
telesnopoškodbo.
Vijačenje
Trdnoprimiteorodjeinnastavitekonicovijačnega
nastavkanaglavovijaka.Pritisniteorodjedotemere,
danastaveknemorezdrsnitizvijaka,tervklopiteorodje
zazačetekdela.
Zategovanje vijakov
Optimalenzateznimomentjemeddrugimodvisenod
velikostiintrdnostivijakatermaterialov,kijihspajamoz
vijačnimizvezami.Zvezomedzateznimmomentomin
časomprivijanjakažejoslike.
120
100
80
60
40
20
Standardni vijak
N m
Pritrdilni moment
Čas pritrjevanja
Pravilni pritrdilni moment
(kgf cm)
(1.224)
(1.020)
(816)
(612)
(408)
(204)
(S)
0 1,0 2,0 3,0
(M14)
(M12)
(M10)
(M8)
0
M14
M12
M10
M8

20 SLOVENŠČINA
120
100
80
60
40
20
Visokonatezni vijak
N m
Pritrdilni moment
Čas pritrjevanja
Pravilni pritrdilni moment
(kgf cm)
(1.224)
(1.020)
(816)
(612)
(408)
(204)
(S)
01,0 2,03,0
(M12)
(M10)
(M8)
0
M12
M10
M8
OPOMBA:
• Kadarjenačindelovanjanastavljennanačin
udarnegavijačnika,sepredopravilomprepri-
čajte,aliorodjepravilnoudarja,takodaprivijete
lesnivijak.Čeorodjenedelujepravilno,stopite
vstikznajbližjimservisnimcentromMakita.
• Orodjedržitenaravnostnavijak.
• Uporabitepravilninastavekzaglavovijaka/
zatiča,kigaželiteuporabiti.
• PrizategovanjuvijakovdimenzijeM8oz.manj-
šihprevidnoregulirajtepritisknavklopno-izklo-
pnostikalo,dasevijaknepoškoduje.
• Obprekoračitvičasaprivijanja,kijenavedenv
tabeli,lahkovijakalivijačninastavekpreobre-
menitealipoškodujete.Optimalenčasprivijanja
bostenajlažjedoločilispredhodnimposkusnim
vijačenjem.Danebipoškodovalivijačnega
nastavkaalivijaka,opraviteposkusnovijačenje.
Napritrdilnimomentvplivavelikorazličnihdejavnikov,
vključnoznaslednjimi.Poprivijanjuvednopreverite
navorzmomentnimključem.
1. Kadarseakumulatorizprazni,seznižanapetostin
s tem tudi zatezni moment.
2. Vijačnialinatičninastavek
Uporabavijačnegaalinatičneganastavka
napačnedimenzijepovzročizmanjšanjezate-
znega momenta.
3. Vijak
• Čepravstakoličniknavorainvrstavijaka
enaka, se bo pravilni pritrdilni moment razli-
kovalgledenapremervijaka.
• Čepravsopremerivijakovenaki,sebo
pravilni pritrdilni moment razlikoval glede na
količniknavora,vrstoindolžinovijaka.
4. Načindržanjaorodjaalipoložajmateriala,kiga
boste pritrdili, bo vplival na navor.
5. Zateznimomentsezmanjšatudivprimeru,če
vijakprivijateznizkimštevilomvrtljajev.
Način udarnega vrtanja
POZOR:
• Meddelomvednotrdnodržiteorodje.Poprevr-
tanjuizvrtine,zamašenezodrezkiindelcialiob
stikunastavkazželeznimipalicamivarmiranem
betonu,delujejonaorodje/nastavekizjemno
visoke in nenadne sile.
Uporabljajtesamosvedreskarbidnotrdino.
Svederpostavitenaželenomestovrtanjainpritisnite
stikalozavklop.Neuporabljajtečezmernesile.Z
zmernosilobostedoseglinajboljšerezultate.Držite
strojnamestu,dasvedernezdrsneizvrtine.
Česeizvrtinazamašizodkruškialiodrezki,nepove-
čujtepritiska.Vtemprimerurajepustitestrojdelovati
brez obremenitve, nato pa sveder postopoma odstranite
izvrtine.Sponavljanjempostopkalahkoočistiteizvrtino
innadaljujeteobičajnovrtanje.
Način vrtanja
POZOR:
• Čezmernopritiskanjenastrojnebopospešilo
napredovanjasvedramedvrtanjem.Nasprotno,
sčezmernimpritiskanjemsepoškodujekonica
svedra,karzmanjšaučinkovitostdelovanjater
skrajšaživljenjskodobostroja.
• Poprevrtanjumaterialadelujejonastrojoz.
nastavekizjemnovisokesile.Strojdržitetrdno
in bodite pozorni na trenutek, ko sveder prodre
skozi obdelovanec.
• Blokiran sveder preprosto sprostite tako, da s
stikalomzaizbirosmerivrtenjaspremenitesmer
vrtenja.Čestrojanedržitedovoljtrdno,lahko
nepričakovanoodskoči.
• Majhneobdelovancevednovpnitevprimežali
jihpritrditevvijačnospono.
• Kadarjemotorzaklenjen,nevlecitesprožilnega
stikala.Orodjeselahkopoškoduje.
Kadarvrtatevles,bostenajboljšerezultatedosegli
ssvedrizales,kisoopremljenizvodilnimvijakom.
Vodilnivijakolajšavrtanjezvlečenjemnastavkav
obdelovanec.
Kadarvrtatevkovino,morate,dabostepreprečilizdrs
nastavkanazačetkuvrtanja,nareditivdolbinoscen-
trirnikominkladivomvtočki,kjerbostevrtali.Nastavite
koniconastavkanavdolbinoinzačnitevrtati.
Kadarvrtatevkovino,uporabitemazivozarezanje.
Izjemastaželezoinmedenina,kijujetrebavrtatisuha.
OPOMBA:
• Izberite primerno hitrost za delovno obremeni-
tev.Zaradivrtanjapreknaslednjezmogljivosti
selahkoorodjepoškoduje.