Malmsten 1514014 User manual
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Assembly Instructions
Water Polo Team Bench (1514014)
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
TOOLS AND EQUIPMENT REQUIRED TOOLS AND EQUIPMENT RECOMMENDED (OPTIONAL)
Hex key #5 (included)
Hex key #6 (included)
Flat spanner 13 (included)
Cordless screwdriver with hex bits
Blankets, soft lining or protection tiles (velour surface)
RECOMMENDED SAFETY CLOTHING (to be worn during the installation and maintenance)
Steel toe work boots
Working gloves
1. 2 6. 2
2. 2 7. 2
3. 1 8. 2
4. 2 9. 6
5. 1 10. 1
Frame 02 Bottom seat
frame
Frame 03 Supporting
profile
Frame 04 Handrail
Frame 05 Angle bracket
Frame 06 Aluminum
connector
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
TOOLS AND EQUIPMENT REQUIRED TOOLS AND EQUIPMENT RECOMMENDED (OPTIONAL)
Hex key #5 (included)
Hex key #6 (included)
Flat spanner 13 (included)
Cordless screwdriver with hex bits
Blankets, soft lining or protection tiles (velour surface)
RECOMMENDED SAFETY CLOTHING (to be worn during the installation and maintenance)
Steel toe work boots
Working gloves
11. 1 16. 20
17. 10
18. 40
19. 8
20. 20
21. 14
22. 26
23. 8
24. 8
12. 1
13. 1
14. 2
15. 2
Bottom
checkered
plate
Rectangular
nut M8
Plastic seat
Self-drilling
screw, DIN
7504-P4 2x25
Hex socket button
cap screw ISO
7380-1 M8x16
Hex socket cap
screw with low
head DIN 6912
M8x20
Hex socket cap
screw with low
head DIN 6912
M8x60
Hex socket cap
screw with low
head DIN 6912
M10x60
Hex socket cap
screw with low
head DIN 6912
M10x65
Hex socket cap
screw DIN 912
M10x90
Upper check-
ered plate
left
Upper check-
ered plate
right
Supporting
profile
Seat frame
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
I - Preparations
1.1 Prepare the tools and put on your necessary safety clothing
1.2 Cover the floor with blankets / soft lining / protection tiles in order to prevent eventual product
or floor damages
1.3 Unpack the product and lay it down safely on the prepared floor
1.4 Check carefully if any of the delivered items are damaged or missing (a list of components can be
found above)
Please Note: Once the bench is assembled correctly, and upon your next inspection (recommended approx. once
a week) you should go over and retighten all bolts.
Certain bolts can benefit from retightening and sometimes the additional application of a product like Loctite.
Loctite, is like a glue, and will lock permanently the bolts in its position.
Loctite can be purchased in most hardware stores.
26. 42 33. 6
25. 14 32. 6
27. 8 34. 4
28. 84 35. 8
29. 14 36. 1
30. 42 37. 1
31. 32 38. 1
DIN 1587 M8
cap nut
Plastic plug
80x40
DIN 1587 M10
cap nut
Plastic plug
40x40
DIN 125 A8,4
washer
Plastic plug
fi35.
DIN 125 A10,5
washer
del 35 Plastic hole
plug fi20
DIN 127 A8
washer
Hex key #5
DIN 127 A10
washer
Hex key #6
DIN 9021 A8,4
enlarged washer
Flat spanner
13 mm
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Step 2
–
A
ssembly
the main frame
Do not tighten all the screws yet. This must be done after all the assembly process is done.
2.1
Start assembling the main frame
using:
1) Frame 03 (2) – 1 pcs
2) Frame 05 (4) – 1 pcs
3) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 4 pcs
4) DIN 125 A10,5 washer (17) – 8 pcs
5) DIN 127 A10 washer (19) – 4 pcs
6) DIN 1587 M10 cap nut (22) – 4 pcs
See Det. A
2.2
Assembling the
next
frame
s
Assemble
the
frames 02 (1), 06 (5)
using:
1) Frame 02 (1) – 1 pcs
2) Frame 06 (5) – 1 pcs
3) Hex socket cap screw with low head
DIN 6912 M10x65 (26) – 4 pcs
4) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 1 pcs
5) DIN 125 A10,5 washer (17) – 10 pcs
6) DIN 127 A10 washer (19) – 5 pcs
7) DIN 1587 M10 cap nut (22) – 5 pcs
See Det. B2, B3
Assemble
the
frame 04 (3)
u
sing:
1) Frame 04 (3) – 1 pcs
2) Hex socket cap screw with low head
DIN 6912 M10x65 (25) – 2 pcs
3) DIN 125 A10,5 washer (17) – 4 pcs
4) DIN 127 A10 washer (19) – 2 pcs
5) DIN 1587 M10 cap nut (22) – 2 pcs
See Det. B4
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
2.
3
Assembling the
next
frame
s
Assemble
the
frames 02 (1), 06 (5)
using:
1) Frame 02 (1) – 1 pcs
2) Frame 06 (5) – 1 pcs
3) Hex socket cap screw with low head
DIN 6912 M10x65 (26) – 4 pcs
4) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 1 pcs
5) DIN 125 A10,5 washer (17) – 10 pcs
6) DIN 127 A10 washer (19) – 5 pcs
7) DIN 1587 M10 cap nut (22) – 5 pcs
See Det. C2, C3
Assemble
the
frame 04 (3)
using:
1) Frame 04 (3) – 1 pcs
2) Hex socket cap screw with low head
DIN 6912 M10x65 (25) – 2 pcs
3) DIN 125 A10,5 washer (17) – 4 pcs
4) DIN 127 A10 washer (19) – 2 pcs
5) DIN 1587 M10 cap nut (22) – 2 pcs
See Det. C4
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
2.
4
Assembling the end frame
Assemble
the end frame 03 (2)
u
sing:
1) Frames 03 (2) – 1 pcs
2) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 4 pcs
3) DIN 125 A10,5 washer (17) – 8 pcs
4) DIN 127 A10 washer (19) – 4 pcs
5) DIN 1587 M10 cap nut (22) – 4 pcs
See Det. D
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
2.
5
Attachi
ng the
supporting profile
Connect two parts of supporting profile and
put it in the
place indicated by the dashed line:
1) Supporting profile (7) – 1 pcs
2) Supporting profile (13) – 1 pcs
3) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 2 pcs
4) DIN 125 A10,5 washer (17) – 4 pcs
5) DIN 127 A10 washer (19) – 2 pcs
6) DIN 1587 M10 cap nut (22) – 2 pcs
See Det. E
Connect the supporting profile to the pre
-
installed main
frame:
1) Hex socket cap screw with low head
DIN 6912 M8x60 (24) – 4 pcs
2) DIN 125 A8,4 washer (16) – 8 pcs
3) DIN 127 A8 washer (18) – 4 pcs
4) DIN 1587 M8 cap nut (21) – 4 pcs
See Det. F
After that cover up all mounting holes by:
1) hole plug fi20 (35) – 4 pcs
See Det. G
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Step 3
–
A
ssembly the checkered plates
3.1
Please check if plates are properly secured with
the
edge
covers (32)
Put the checkered plates (10, 11, 12) on the main frame
and screw using:
1) Bottom checkered plate (10) – 1 pcs
2) Left upper checkered plate (11) – 1 pcs
3) Right upper checkered plate (12) – 1 pcs
4) Self-drilling screw DIN 7504-P 4,2x25 (27) – 40 pcs
Step 4
–
Assembly the seats
4.1
Assembling the bottom seat frames
Assemble
the
seat frame (6)
usi
ng:
1) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 4 pcs
2) DIN 125 A10,5 washer (17) – 8 pcs
3) DIN 127 A10 washer (19) – 4 pcs
4) DIN 1587 M10 cap nut (22) – 4 pcs
See Det. I
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
4.2
Assembling
the upper seat frame
Assemble
the
angle bracket
s
(9)
using:
1) Angle brackets (9) – 6 pcs
2) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 4 pcs
3) DIN 125 A10,5 washer (17) – 8 pcs
4) DIN 127 A10 washer (19) – 4 pcs
5) DIN 1587 M10 cap nut (22) – 4 pcs
See Det. J, K
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Connect two parts of
the upper
supporting profile:
1) Supporting profile (7) – 1 pcs
2) Supporting profile (13) – 1 pcs
3) Hex socket cap screw with low head
DIN 6912 M10x60 (25) – 2 pcs
4) DIN 125 A10,5 washer (17) – 4 pcs
5) DIN 127 A10 washer (19) – 2 pcs
6) DIN 1587 M10 cap nut (22) – 2 pcs
See Det. L
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Connect
the supporting profile
and the main frame using:
1) Hex socket cap screw with low head
DIN 6912 M8x60 (24) – 4 pcs
2) DIN 125 A8,4 washer (16) – 8 pcs
3) DIN 127 A8 washer (18) – 4 pcs
4) DIN 1587 M8 cap nut (21) – 4 pcs
See Det. M
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
Connect two parts of
the
upper seat frame:
1) Seat frame (14) – 2 pcs
2) Hex socket button cap screw
ISO 7380-1 M8x16 (29) – 8 pcs
3) Aluminum connector (30) – 1 pcs
See Det. N
Next put it on the main frame and place additional
rectangular nut M8 into the groove of the profile
to be used later!
1) Rectangular nut M8 (15) – 20 pcs
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
After that
assemble the plugs
:
1) hole plug fi20 (35) – 4 pcs
2) plug 40x40 (36) – 4 pcs
3) plug 80x40 (33) – 4 pcs
See Det. P, R
Assemble the
upper seat frame
using:
1) Hex socket cap screw with low head
DIN 6912 M8x60 (24) – 6 pcs
2) DIN 9021 8,4 washer (28) – 12 pcs
3) DIN 127 A8 washer (18) – 6 pcs
4) DIN 1587 M8 cap nut (21) – 6 pcs
See Det. S
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
4.3
Assembling the seats
Assemb
le
the
seats (31)
using:
1) Seat (31) – 10 pcs
2) Hex socket cap screw with low head
DIN 6912 M8x20 (23) – 20 pcs
3) DIN 9021 8,4 washer (28) – 20 pcs
See Det. T
Step 5 – Assembly the handrails
5.1
Assembling the
left
ha
ndrail
Assemble the
left
handrail (8) using:
1) Handrail (8) – 1 pcs
2) Hex socket cap screw
DIN 912 M10x90 (25) – 4 pcs
3) DIN 125 A10,5 washer (17) – 8 pcs
4) DIN 127 A10 washer (19) – 4 pcs
5) DIN 1587 M10 cap nut (22) – 4 pcs
Cover the ends of the pipe by:
1) Plug fi35 (34) – 2 pcs
See Det. U
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
5.2
Assembling the
right
handrail
Assemble the
right
handrail (8) using:
6) Handrail (8) – 1 pcs
7) Hex socket cap screw
DIN 912 M10x90 (25) – 4 pcs
8) DIN 125 A10,5 washer (17) – 8 pcs
9) DIN 127 A10 washer (19) – 4 pcs
10) DIN 1587 M10 cap nut (22) – 4 pcs
Cover the ends of the pipe by:
2) Plug fi35 (34) – 2 pcs
See Det. W
II. Maintenance and Service
For any queries regarding product, spare parts or problems please contact:
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
II. Maintenance and Ser-
vice
For any queries regarding pro-
duct, spare parts or problems
please contact:
III. Maintenance and Service
To ensure long-lasting and safe use of the equipment, periodical inspections are required:
• Every time before using the equipment:
• Visually check if there are any parts damaged or missing
• Check if all the devices are installed correctly and secured to prevent tilting/moving
• Every 6 months a detailed check-up of the equipment is required:
Visual checkup if any deformities, damages, missing or worn out parts have occurred. Tighten
all assembly nodes (in order to make sure that all screws and nuts are tightened).
Care and Usage Instruction:
• Only use tools delivered with the bench for periodical tightening of the screws, otherwise the
bolts and nuts may corrode.
• If any atypical signs are noticed (for instance squeaky noises, missing elements, or visual da-
mages) immediately stop further usage of the equipment and report the problem to the manu-
facturer or its authorized distributor.
WARNING:
Storage and usage shall be so that no unauthorized person or child can acci-
dently be injured by a falling or tilting bench. THIS IS NOT A TOY !
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
IV. TERMS OF WARRANTY
1 General Provisions
1.1 M. MALMSTEN AB (the “Manufacturer”) provides the limited warranty (the “Warranty”) to the
purchaser of the Equipment. Warranty is only valid in the facility in which the Equipment was
originally installed. The Warranty is valid from the time of the final acceptance of the building or
from the date of delivery and to the timeline listed below, under the terms and conditions stated
below.
No. Element Warranty
1 1514014 Water Polo Team Bench 12 months
1.2 The manufacturer warrants the Equipment against defects in material or factory workmanship
which is caused by failure of the Equipment within the applicable Warranty Period.
1.3 In case of a defect discovered, the purchaser is obtained to immediately (not later than after 7
days) inform the manufacturer or authorized distributor about the problem. The manufacturer or
its authorized distributor will answer within 14 days and will propose a way to solve the issue.
1.4 The purchaser is obtained to provide information about failures or defects in writing to
1.5 The information about warranty claims should include the serial number, description of the issue
and date of discovering of the defect. Photographic documentation will be required.
1.6 The manufacturer/distributor, once it confirms the existence of a covered defect will (at its sole
discretion) repair or replace the defective parts.
1.7 Defects or damages that occurred during proper use will be repaired or replaced by the manu-
facturer or by the authorized distributor.
1.8 The warranty covers the costs of investigation, production and shipping. Disassembly of the da-
maged and installation of the new/repaired part/parts is not covered.
WARNING:
All unauthorized (not provided by the distributor or manufacturer) self-
repairs, adjustments or interferences in the equipment can cause irreparable
damages and dangerous accidents.
Art. No. 1514014www.malmsten.com
Malmsten AB • www.malmsten.com
v.11-22E
2 Exclusions and Conditions:
• Operations, which shall be made by the user and on his cost, such as maintenance of cleanli-
ness, periodical checkups (as in point 2.1)
• Mechanical and chemical damages caused by improper use and maintenance (i.e. attempts of
self-repair; lack of maintenances and inspections; using inadequate cleaning agents, adjust-
ments made by the user)
• Mechanical damages caused by the excessive burden on the equipment
• Damages caused by the user or third party (including acts of vandalism) hang, swing or climb
on the equipment
• Consumable parts
• Damages caused by operation of the equipment by non-authorized persons
• Installation of the equipment not performed in accordance with the assembly manual
• Damages caused by natural disasters such as floods, fire, wind, lightening or other acts of
nature
• Damages caused by usage not in accordance with equipment destination
3 Post-warranty Services
3.1 After the warranty expires, it is recommended to order a professional post-warranty service
performed by the authorized distributor once every 12 months in order to make sure, that the
equipment is in good condition and can be used safely.
3.2 In case of a failure discovered after the time of warranty, the user might inform the manufactu-
rer or it’s authorized distributor about the problem in the same way which is described in point
1.4. The manufacturer or distributor will offer a solution to the problem within 7 days. After the
claim is accepted, both parties will agree on a suitable term of repairs.
Table of contents
Other Malmsten Sport & Outdoor manuals
