Manitowoc LuminIce K-00424 Instructions for use

Installation, Use & Care Manual
America’s #1 Selling Ice Machine
This manual is updated as new information and models are released.
Visit our website for the latest manual. www.manitowocice.com
This manual contains English and French text
LuminIce™
Manitowoc
Part Number 000008463 10/11

Table of Contents
2Part Number 000008463 10/11
Section 1
General Information Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
LuminIce™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Section 2
Installation Instructions
LuminIce™ Installation 30" Wide Single Evaporator Models . . . . . . . . . . . . . . . . 5
LuminIce™ Installation 48" Wide Single Evaporator Models . . . . . . . . . . . . . . . . 7
LuminIce™ Installation Two Evaporator Ice Machines . . . . . . . . . . . . . . . . . . . . . 10
LuminIce™ Reminder Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Section 3
Customer Support Cleanup Procedure for Accidental Bulb Breakage . . . . . . . . . . . . . . . . . . . . . . . . 13
Before Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
During Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
After Cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleanup Steps for Hard Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleanup Steps for Carpeting or Rugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Future Cleaning of Carpeting or Rugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Part Number 000008463 10/11 3
Section 1
General Information
This manual covers installation of the LuminIce™ on the
following ice machine models:
Kit K00424 is used with 22" & 30" wide single
evaporator models (i0300 through i1000)
Kit K00434 is used with all 48" wide or dual
evaporator models
Before You Begin
Remove all packing material and inspect the equipment
for concealed shipping damage. If damage is found,
notify the shipper immediately.
LuminIce™ is for use on Indigo™ ice machines and is
not compatible with previous series ice machines.
Self-Contained
Air-Cooled Self-Contained Water-Cooled Remote Condenser
QuietQube
Remote
Condensing
Unit
ID0302A
IY0304A ID0303W IY0305W ---- ---- ---- ----
ID0322A
IY0324A ID0323W IY0325W ---- ---- ---- ----
ID0452A
IY0454A ID0453W IY0455W ---- ---- ---- ----
IR0500A
ID0502A
IY0504A
IR0501W
ID0503W
IY0505W
IR0590N
ID0592N
IY0594N
----
----
----
IR0520A
ID0522A
IY0524A
IR0521W
ID0523W
IY0525W
----
----
----
----
----
----
ID0602A
IY0604A ID0603W IY0605W ID0692N IY0694N ID0682C IY0684C
IB0694YC
IR0850A
ID0852A
IY0854A
IR0851W
ID0853W
IY0855W
IR0890N
ID0892N
IY0894N
ID0872C
IY0874C
IB0894YC
ID1002A
IY1004A ID1003W IY1005W
ID1003WM
ID1092N
IY1094N ID1072C IY1074C
IB1094YC
ID1202A
IY1204A ID1203W IY1205W --- --- --- ---
ID1402A
IY1404A ID1403W IY1405W
ID1403WM
ID1492N
IY1494N ID1472C IY1474C
IR1800A
ID1802A
IY1804A
IR1801W
ID1803W
IY1805W
IR1890N
ID1892N
IY1894N
ID1872C
IY1874C
---- ---- ---- ID2172C
IY2174C
! Warning
PERSONAL INJURY POTENTIAL
Do not operate equipment that has been misused,
abused, neglected, damaged, or altered/modified
from that of original manufactured specifications.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision concerning use of the appliance by a
person responsible for their safety.

General Information Section 1
4Part Number 000008463 10/11
LuminIce™
The LuminIce™ growth inhibitor recirculates the air in
the ice machine foodzone over a UV bulb. This process
will inhibit the growth of common micro-organisms on all
exposed foodzone surfaces.
• LuminIce™ bulbs require replacement on a yearly
basis. Although the bulb will still illuminate after 12
months, the effectiveness of the bulb diminishes as
operational hours increase. To retain maximum
effectiveness, replace the bulb on a 12 month
schedule.
• The control board can be set to automatically display
a reminder after 12 months. Refer to Section 2
LuminIce™ setup procedure for full details.

Part Number 000008463 10/11 5
Section 2
Installation Instructions
LuminIce™ Installation 30" Wide Single
Evaporator Models
1. Disconnect all power to the ice machine at the
electrical disconnect.
2. To allow access for LuminIce™ tubing, the
evaporator dust cover and plastic caps in the
evaporator and compressor compartment bulkhead
wall must be removed and discarded.
3. Assemble bracket to left-hand top rail with three
provided screws.
!Warning
Disconnect power to ice machine at the electrical
disconnect. Pressing the power button does not
disconnect line voltage.
Remove Plastic Caps From Bulkhead In The
Evaporator And Compressor Compartment
Mount Bracket With
Three Screws

Installation Instructions Section 2
6Part Number 000008463 10/11
4. Assemble LuminIce™ to bracket with three screws
provided. The bulb and bulb wiring must face toward
the rear of the ice machine to allow bulb
replacement with LuminIce™ in place.
5. Mount transformer on evaporator bulkhead above
control box. Attach supplied wire clip and route line
voltage wires through clip.
6. Route line voltage wires (Black & White) through line
voltage Heyco fitting and attach to L1 and L2
contactor terminals.
NOTE: QuietQube models do not have open terminals
on contactor. Remove two wires from contactor, install
supplied electrical connector and connect wires.
Attach With Three Screws
Route Line Voltage Wires Through Clip
Install Transformer Attach Wire Clip
Route Through Line Voltage Heyco
and
Attach to Contactor Terminals
LuminIce Power
L1
L2
Wires Removed From Contactor Contactor

Section 2 Installation Instructions
Part Number 000008463 10/11 7
7. Route low voltage wiring (black and yellow wires) to
the LuminIce™. Install wire clip and route wires
close to evaporator bulkhead to assure harness is
away from any moving parts, then snap wire
harness connectors together.
8. Install LuminIce™ hoses.
• Insert hose closest to the front of the ice machine in
the bottom evaporator bulkhead hole.
• Insert hose farthest from the front of the ice machine
in the upper evaporator bulkhead hole.
9. Install the notched evaporator dust cover from kit
and test run the ice machine and LuminIce™. The
Luminice™ is energized whenever power is applied
to the ice machine.
LuminIce™ Installation 48" Wide Single
Evaporator Models
1. Disconnect all power to the ice machine at the
electrical disconnect.
2. To allow access for LuminIce™ tubing, the
evaporator dust cover and plastic caps in the
evaporator and compressor compartment bulkhead
wall must be removed and discarded. Remove the
evaporator dust cover to access lower cap.
Install wire clip and route wires
along evaporator bulkhead.
!Warning
Disconnect power to ice machine at the electrical
disconnect. Pressing the power button does not
disconnect line voltage.
Remove Plastic Caps From Bulkhead In The
Evaporator And Compressor Compartment
Remove Dust Cover

Installation Instructions Section 2
8Part Number 000008463 10/11
3. Remove bracket from ice machine and assemble
LuminIce™ and transformer to bracket. Attach
tubing and secure with hose clamps.
4. Assemble bracket to ice machine.
Mount LuminIce™ and
Transformer To Bracket

Section 2 Installation Instructions
Part Number 000008463 10/11 9
5. Route line voltage wires (Black & White) through line
voltage Heyco fitting and attach to L1 and L2
contactor terminals.
NOTE: Three phase models do not have open terminals
on contactor. Remove two wires from contactor, install
supplied electrical connector and connect wires.
6. Route LuminIce™ hoses to evaporator and attach.
• Insert hose closest to the front of the ice machine in
the bottom evaporator bulkhead hole.
• Insert hose farthest from the front of the ice machine
in the upper evaporator bulkhead hole.
7. Install the evaporator dust cover and test run the ice
machine and LuminIce™. The Luminice™ is
energized whenever power is applied to the ice
machine.
Route Through Line Voltage Heyco
and
Attach to Contactor Terminals
LuminIce Power
L1
N
Ice Machine Power Incoming Power Supply

Installation Instructions Section 2
10 Part Number 000008463 10/11
LuminIce™ Installation Two Evaporator Ice
Machines
1. Disconnect all power to the ice machine at the
electrical disconnect.
2. To allow access for LuminIce™ tubing, the plastic
caps in the evaporator compartment bulkhead wall
must be removed and discarded. Cap located
behind evaporator will fall into the water trough.
Remove water trough to retrieve cap, then discard.
3. Cut hose to length.
• Cut one hose 8" (20 cm) long.
• Cut one hose 18" (46 cm) long.
4. Assemble LuminIce™.
• Assemble LuminIce™ to bracket.
• Install tubing and secure with hose clamps.
• Insert a tubing adapter into each hose.
NOTE: The bulb and bulb wiring must face toward the
top of the ice machine to allow bulb replacement with
LuminIce™ in place.
5. Attach Luminice™ assembly to corner post with two
screws.
6. Mount transformer to evaporator bulkhead.
!Warning
Disconnect power to ice machine at the electrical
disconnect. Pressing the power button does not
disconnect line voltage.
Remove Plastic Caps From
Evaporator Bulkhead