Marantz RX-77 User manual

Model RX-77 User Guide
RF Extender
Introduction
Possible Set-ups
The RF Extender can be used in several situations:
•Your devices can be remotely controlled while the
RF Extender is placed in line of sight (situation A).
•The set-ups in situation A, B and C can
be combined. If you want to control
devices in different locations,
you have to place
• The RF Extender controls devices placed in
an adjacent room (situation B).
•The RF Extender is placed inside a closet
or a rack together with your devices
(situation C ).
You can operate all
RF Extenders with
See Multiple RF Extenders on p. 6 to
apply the necessary settings.
Situation B
Situation C
Situation A
a RF Extender in
each location.
one remote control.
RX-77 07-25-2001 Page 1 of 6
User Guide
1

Working Angle and Range of the IR blaster
Warning The IR signals sent out by the RF Extender always have to be able to reach the
receiving eyes of your devices. Make sure that the IR blaster (dark plastic window
on top of the RF Extender) is aimed at your devices.
RX-77 07-25-2001 Page2 of 6
Minimum distance:4 inches (10 cm)
Maximum distance: Approx. 16 feet (5m)
Before you install the RF Extender, you should decide which of the
set-up described on p. 1 apply to your needs.
It is also possible to place RF Extender with the IR blaster facing up. In this case,
the RF Extender can be placed at a distance and higher than the devices.
Make sure there are no objects between the RF Extender and the receiving eyes.
Mounting
The RF Extender can be mounted to a piece of furniture using the included
mounting plate and the 4 screws. Take into account the range and the working
angle of the IR blaster. Also make sure to place the RF Extender in a
central position aimed directly at your devices.
Warning It is adviced not to place the RF Extender inside or near a metal closet as
RF signals can be disturbed by metal objects.
Installation
To get optimal results, it is recommended to place the RF Extender horizontally
with the IR blaster facing up or down.
from the bottom of the
1Remove the mounting plate
2Screw the plate where you
want to place the RF Extender.
Provide space to connect the
power adapter.
3Slide the RF Extender on the
mounting plate.
Place the RF Extender mounted
up side down inside a closet.
Always maintain a minimum
distance of 4 inches (10 cm)
between the RF Extender and
your devices.
RF Extender.
User Guide
2

User Guide
3
1Attach the emitter around the receiving eyes of your devices. It is suggested
to adjust the location to find the most sencitive area before fix the emitter.
2 Plug the dual IR emitters into the RF Extender.
Note To avoid interference, the wires of the
emitters should be kept away from the
RF Extender as far as possible.
Connecting the Power Adapter
When connecting the power adapter it is recommended
that you plug the adapter into the RF Extender before
you plug it into the socket. When connected you will
see a red LED on the RF Extender.
should be kept away from the
RF Extender as far as possible.
RX-77 07-25-2001 Page3 of 6
Emitter
How to use the emitters
Note To avoid interference, the adapter cable
The IR emitters can control devices the IR blaster cannot reach, for instance when
there is limited space in a small closet, it can be placed in a location as to where
the infrared receiver, can receive the signal.
Using the Dual IR Emitters
You can use the dual IR emitters as an alternative for the IR blaster.
Note The IR emitters can also be used in combination with the IR blaster of the
RF Extender. Both send out IR signals simultaneously. This allows you to operate
several devices using both the IR blaster and the IR emitters.
Installation

Installation
User Guide
4
Settings
As the RF Extender ‘communicates’ with RC5200/RC9200, you have to set the
same Extender ID (identity) on both appliances. The settings depend on whether
you have a single RF Extender or multiple RF Extenders.
Single RF Extender
When you use only one RF Extender, you can accept the default setting for the
Extender ID (ID=0). Make sure your Remote Control is set to the same default
setting (see the RC5200/RC9200 User Guide for more details).
Multiple RF Extenders
If you want to operate several of your devices independently, e.g. grouped on
different locations, you will need multiple RF Extenders. When using several
RF Extenders, it is important to assign a unique Extender ID to each RF Extender.
16 Extender IDs (from 0 to 9 and from A to F) can be assigned.
1 Choose an Extender ID for the RF Extender by turning
the ID dial with a small screwdriver.
2On the Remote Control, choose the same
Extender ID for each device controlled
by the RF Extender.
Refer to the RC5200/RC9200 User Guide for
more detail information.
3Try to operate your devices with the Remote Control.
The red LED will blink when the RF Extender receives a correct command.
4 Repeat this procedure for every RF Extender.
RF Interference
If your devices are not responding to commands or if the red LED on the IR blaster
is blinking without sending commands, it might be possible that there is RF
interference. This can be the case when other RF appliances are operated nearby,
for instance at your neighbours.
When you notice RF interference, you have to choose another channel on your
RF Extender.
RX-77 07-25-2001 Page4 of 6

User Guide
5
Troubleshooting
Troubleshooting
Devices do not respond properly
• Check if the power adapter is connected and the red LED is on.
• Check if the ID and channel numbers on the RF Extender match with the ID and
channel numbers on the ProntoPro Remote Control (see p. 6). Refer to the
RC5200/RC9200 manual for more details on the settings of the Remote Control.
• Check the placement of the RF Extender:
•Check the distance between the RF Extender and the remote control
(see p. 2).
•Check the range and the working angle of the IR blaster.
•Check if the RF Extender is placed in a central position relative to your
devices.
•Make sure that the distance between the RF Extender and your device is
at least 4 inches (10 cm).
•Make sure that the distance between the RF Extender and your device is
at most 16 feet (5 m).
•Make sure the IR signals between the RF Extender and the receiving eyes
of your devices are not disturbed by any objects.
•Check if metal objects, for instance a metal closet, wires or cables,
surrounding the RF Extender do not disturb the RF signals.
•If you are using the dual IR emitters, make sure they are connected
properly and that they are placed within range of the receiving eyes
(see p. 3).
• It might be possible that some commands cannot be sent out as RF signals.
In that case you will have to reconfigure RC5200/RC9200 to operate your
devices with IR signals again.
The red LED on the RF Extender blinks while you are not using remote
control
• This indicates RF interference. Another device in the proximity is sending out
RF signals. Change the channel (CH) on the RF Extender (see p. 4).
There is no red LED on my RF Extender
• Check if the power adapter is connected properly.
The dual IR emitters are no longer adhesive
• Replace the adhesive with a fresh piece of the 2-sided tape.
I cannot find the exact location of the device’s receiving eye
• Check the manual of the device.
When still in doubt, contact your supplier or the manufacturer.
RX-77 07-25-2001 Page5 of 6

User Guide
6
Hardware Red LED (continuously on when powered, blinking during RF reception)
16 IDs and 4 CHs , 4 outputs for IR emitters
Dimensions 4.5 x 3.2 x 1.2 inch (113 x 81 x 30 mm)
Operating 32°F to 122°F (0°C to 50°C)
temperature
Infrared (IR) Operating distance: up to 16 feet (5 meters)
IR frequency range: DC/flash codes, 36kHz-550kHz
Radio Operating distance: up to 100 feet (30 meters)
frequency (RF) depending on the surrounding conditions
Frequency: 418 MHz (US) , 434MHz (Europe)
Dual IR emitters Number of IR emitters: up to 8 (4x2), emitters wired in series
3.5mm mono mini-plug
Cable length: 10 feet (2.5 meters) , Max. range: 3 feet (75 cm)
Accessories AC Power adapter (400mA/12V DC adapter)
Mounting kit (Plate and 4 screws)
Approvals The device complies with part 15.19(a)(3) of the FCC Rules.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept
any interference received including interference that may cause
undesired operation.
Specifications
RX-77 07-25-2001 Page6 of 6
IR emitter x 4
The specification and design of this product are subject to change without notice.