Marco X-Series User manual

X-Series
Aquarium Stands
ASSEMBLY INSTRUCTIONS
Customer Service: Toll Free: 1-888-627-2601 (Monday - Friday, 8:30 AM to 4:30 PM CST
Marco Group Inc., 5400 Doniphan Drive, Neosho, MO 64850
10 Gallon
Model# 5X10-1
20 Gallon
Model# 5X20-1
29 Gallon
Model# 5X29-1
55 Gallon
Model# 5X55-1
These Assembly Instructions cover all models listed here.

2
BEFORE BEGINNING ASSEMBLY:
Please review the Parts List to ensure you have all the parts
shown here. If you nd missing or broken parts, or are in need
of assembly guidance, call toll free, 1-888-627-2601 and we’ll
be happy to help.
PLEASE DO NOT RETURN THIS MERCHANDISE TO THE STORE.
¼-20 x ¾” Bolt (x3)
Brace (x2)
X Leg (x2)
¼-20 x 1½” Bolt (x8)
¼-20 Lock Washer (x11)
¼-20 Hex Nut (x11)
Wrench (x1)
PARTS LIST
HARDWARE PACK
A
B
C
D
G
E
F
CARE & MAINTENANCE
• Clean furniture with a soft cotton cloth moistened with water.
• DO NOT use abrasives.
• DO NOT leave water on any of the stand’s surfaces. Always
wipe spilled water from the stand. Water, for prolonged
periods, could damage the stand’s surface.
LIMITED WARRANTY
This aquarium stand is under warranty by Marco Group, Inc. against defects
in material and workmanship for 90 days from the date of purchase. If any
component of the stand is found to be defective, you may contact us for
replacement provided that it has not been modied, damaged or misused.
(Proof of date of purchase must be provided).
THIS WARRANTY IS VOID if the aquarium stand is modied, if it is not placed on
a at, level surface, if it is used with a tank other than it is designed, if it is moved
with the tank in place or if it is used for other than it’s intended purpose.
This warranty is limited to replacement of the stand only. Warranty does not
cover loss of sh, personal injury, property loss or damage arising out of use
of the aquarium stand. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may
not apply to you. This warranty gives you specic rights and you may have other
rights that vary from state to state.
IMPORTANT SAFETY INFORMATION
Please read all the following information before assembling and using
your aquarium stand.
THIS PRODUCT IS NOT A TOY – NEVER allow small children to touch, climb
on or play with aquarium or aquarium stand. Serious injury or death could
result.
WHERE TO PLACE YOUR AQUARIUM
Use only an aquarium stand designed to support the weight and size of your
aquarium. The filled weight of an aquarium is approximately 10 to 12 pounds
per gallon. This stand is designed only for use on level surfaces. Failure to
place your stand on a level surface could cause the aquarium to leak, crack or
even tip or fall. Never tip the stand from the upright position.
MOVING YOUR AQUARIUM STAND
Always position the stand in the desired location before putting the
aquarium tank in place. Never attempt to move the stand with the aquarium
in place. Never remove an aquarium tank from the stand unless the aquarium
tank is completely empty. Never carry the stand by the top.
Top Wood Shelf with
Metal Support Assembly (x1)
Note: Shelf support will vary depending on size of stand.
Bottom Wood Shelf with
Metal Support Assembly (x1)
Note: Shelf support will vary depending on size of stand.
H
I

3
Make sure this hole is located on same
side as the two holes located on the
side of the top shelf assembly before
attaching bottom shelf.
TOOL
REQUIRED
ATTACH TOP SHELF
TO LEGS
STEP 1: Place top wood shelf with metal
support “H” upside down on a smooth,
level surface.
NOTE: The Top shelf is the larger of the two shelves.
STEP 2: Place one x-leg inside of top
frame as shown.
STEP 3: Insert 2 bolts “B” through holes
in top and leg and secure each with lock
washer “C” and nut “D”.
NOTE: Leave nuts slightly loose at this time so the
stand can be leveled later.
STEP 4: Repeat above steps for
attaching x-leg on other side.
ATTACH BOTTOM
SHELF TO LEGS
STEP 5: Position bottom wood shelf with metal support as shown here
making sure cross brace holes are located on the same side as noted. Attach bottom shelf
support to inside of legs using 4 bolts “B”. Secure with lock washers “C” and nuts “D”.
NOTE: Leave nuts slightly loose at this time so the stand can be leveled later.
Wrench (supplied)
C
G
C
D
D
B
B
B
BB
I
H
B
C
C
D
D
C
C
D
D
Bottom Wood Shelf
with Metal Support
Top Wood Shelf with
Metal Support

©2021 Marco Group Inc.
ATTACH BRACES
TO FRAME
STEP 6: Attach cross braces “G” to bottom and top shelves as shown using 3 bolts “A”.
Note: Square holes in braces attach to top shelf. Secure each bolt with lock washers “C” and nuts “D”.
STEP 7: Place stand in upright position and check to make sure stand is level and has
proper contact with floor. Once stable, finish tightening down all nuts securely.
Assembly is complete! We hope you enjoy your new X-Series Aquarium Stand!
C
C
C
D
D
D
A
A
A
G
G
NOTE: Attach
square hole end
of brace here.
NOTE: Attach
square hole end
of brace here.