Mark Bric ISOframe IS-9103 User manual

Mounting instructions
Curved standard unitsStraight standard units
Item IS-9108
Width 2290 mm / 90”
Depth 830 mm / 32.5”
Height 1050 mm / 41.5”
Item IS-9109
Width 2760 mm /108.5”
Depth 1060 mm / 41.5”
Height 1050 mm / 41.5”
Item IS-9110
Width 3040 mm / 119.5”
Depth 1330 mm / 52.5”
Height 1050 mm / 41.5”
Item IS-9103
Width 2500 mm / 98.5”
Depth 495 mm / 19.5”
Height 1050 mm / 41.5”
Item IS-9104
Width 3300 mm / 130”
Depth 495 mm / 19.5”
Height 1050 mm / 41.5”
Item IS-9105
Width 4100 mm /161.5”
Depth 495 mm / 19.5”
Height 1050 mm / 41.5”
Starter, curved Item IS-9111
Starter, straight Item IS-9113
Starter & Extension units
Table top end, curved Item IS-9005
Table top center, curved Item IS-9006
Table top end, straight Item IS-9008
Table top center, straight Item IS-9009
Structure - Starter Table tops Inner shelves
Curved Item IS-9007
Straight Item IS-9010
Extension, curved Item IS-9112
Extension, straight Item IS-9114
Structure - Extension

2
4 5
Connect the double-H sections you’ve just built, using 800
mm beams placed at the top and bottom of the posts. H-
sections with mag tape on both posts are used on the
ends; H-sections having mag tape on only one post are
intermediate supports. All front-facing posts should have
mag tape.
31
Select two posts with magnetic tape.
Attach two 400 mm straight beams to these posts, directly
over the stop brackets, building a double-H style section
as shown here. Build a second H in this same manner.
These H-sections become the ends of the counter.
If your counter is more than one section wide, build the
intermediate H-support as follows.
Select one post with mag tape and one post without
mag tape Connect them with two 400 mm straight
beams, placed directly above the stop brackets. Build
one of these H-section supports for each additional sec-
tion of your counter.
2 of 3 sections completed.
Post with
magnetic tape
Post without
magnetic tape
3 of 3 sections completed.
(For longer ISOframe counters with more sectiions, simply repeat these same
assembly steps for each section.)
Post without
magnetic tape
Post with
magnetic tape
Post with
magnetic tape
Stop
bracket
Post without
magnetic tape
Post with
magnetic tape
Posts with magnetic (mag) tape are used on the front
of the counter and on the back outside corners. Posts
without mag tape are used only on the back of the
counter at intermediate sections, not on the corners.
Posts with
magnetic tape
Posts without
magnetic tape
Important
Starting
Note
Attach the FastClamp correctly to the post
Incorrect mounting will weaken the clamp mechanism.
Open FASTclamp Close FASTclamp Wrong – not square Wrong – not square Correct – square
R
QQ

Connect each top section to the other with a connector plate, which attaches to the
underside of the tops with thumbscrews.
Mount the graphic panels on both ends and along the front. Add corner trim strips at all corners to complete the construction.
9
1110
End-section tops attach along the center of the intermediate support posts, and they
overlap the end-section posts.
8
Mount the 3 table tops. Each section is marked either End- or Center-section, indicating
how they are to be placed on the frame structure.
If you want extra stability on the shelves, you can now move the beams at the front
directly under the shelf.
7b 7c
67a
End-section tops have three routed grooves on the underside at each corner. Center-
section has only one groove per corner.
In this example, we are building a 3-section counter, so the framing is now complete.
Now attach the inner shelves by placing them on top of the 400 mm straight beams.
End-section table tops Center-section table tops

Mark Bric Display Corp.
North America Tel. [phone] Fax [phone] E-mail: [email protected]
Mark Bric Display AB
Worldwide Headquarters Tel. [phone] Fax [phone] E-mail: [email protected]
Graphic panel
Item 9514 - 2013.06.23
800 mm / 31 1/2”
1010 mm / 39.77”
Printer material
We recommend the following material:
Semi-rigid PVC panel: 2 - 3 mm / 0.080 - 0.120”
Poster paper: 180 gr / 0.4 lb.
The printed graphic panels must be laminated before use.
Front side: 125 microns (0,125 mm) / 0.005” ”deep crystal”
Reverse side: 250 microns (0,250 mm) /0.010””stop light”
Polyester film: 330-370 microns (0,350 mm) / 0.013-0.015”
Top laminate: 125 microns (0,125 mm) / 0.005” ”deep crystal”
Mounting of Magnetic Tape
Magnetic tape to be fixed vertically along each side of the graphic panels.
IMPORTANT Carefully mount the magnetic tape slightly inset from the edge of
the graphic panel by approximately 0,25 mm / 0.010”. Once mounted, a very
thin straight white line should show between the edge of the graphic and the
outside edge of the magnetic tape. Do not exceed 0,5 mm / 0.020”.
Application Techniques
To obtain optimum adhesion, the bonding surfaces must be well unified, clean
and dry. Typical surface cleaning solvents are isopropyl alcohol/water mixture
(rubbing alcohol) or heptane.
Note: Be sure to follow solvent manufacturer’s precautions and directions for
use when using solvents.
573 mm / 22.56”
Straight & Outside curved Inside curved
400 mm / 15.75”
End
Double side units
Inside curved units
To order a double side reception counter, add ”DS” after the item number!
This will change all posts without magnetic tape to posts with magnetic tape.
All outside curved units can be used as inside units as well.
Mount all posts with magnetic tape on the inside of the curve, rather than the outside,
and mount the beams along the outside of the curve, where posts without magnetic tape
are now located.
Please observe: The graphic panels will no longer be 800 mm. See below for details.
Open
Corner trims
One section openFully closed
Posts without magnetic tape
Posts with magnetic tape
Graphic panel attachments
Vertical magnetic tape
on edge of the graphic
and Edge stiffener
at top and bottom
(not necessary at semi-rigid panels)
Accessories
Magnetic tape (not incl.)
12 mm/0.5” A tape, 30 m / 98 ft. DM-013-AC
Each end section needs: 4,1 m / 14 ft.
Each center section needs: 2,1 m / 7 ft.
Edge stiffener (not incl.), Item IS-9026
This are 900 mm / 35.4” long for custom cutting.
Corner trims in
each corner
Corner trims in
each corner