Marshall Electronics V-LCD70-AFHD User manual

1
Model V-LCD70-AFHD
Operating Instructions

2
This page intentionally left blank

3
Table of Contents
Top and Front Panel Features ............................................................................................................................6
Rear Panel Features............................................................................................................................................7
Compatible Input Formats..................................................................................................................................8
MAIN MENU AND NAVIGATION .........................................................................................................................9
Using the Menu buttons ..................................................................................................................................................................9
Picture Submenu ..............................................................................................................................................................................9
Video & Audio Submenu ................................................................................................................................................................10
Setting Submenu ............................................................................................................................................................................11
OSD Submenu.................................................................................................................................................................................12
Specifications....................................................................................................................................................13
Maintenance.....................................................................................................................................................14
Warranty...........................................................................................................................................................14

4

5
■Included Accessories
Carefully unpack the V-LCD70-AFHD monitor and verify that the following items are included:
• V-LCD70-AFHD Monitor
• 12V 1.5A XLR Power Supply
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately
contact Marshall Electronics at [phone]. If you are not located within the continental United States, call +1 (310) 333-
0606.
■Connections, Power-On and Initial Setup
Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the Power connector to the back of the monitor.
Connect the required cables for video signal input and output. (Power must be applied to the V-LCD70-AFHD for the active loop-
though output to be activated). Press the power switch on the front of the unit. Video will automatically be detected and
displayed on the screen after selecting the proper input.

6
Top and Front Panel Features
Power Switch
This power switch controls power to the monitor from the DC
Power Connector or the custom Battery Adaptor. The monitor
will always attempt to draw power from the DC connector first
if both the DC Power Connector and a Battery are installed
simultaneously. This switch turns the panel on or off.
Function Buttons
Two user-definable function buttons can be used for direct
access to various settings. Functions are assigned using the on-
screen menu.
Input Select Button
Use the Input select button to switch between the different
available video inputs.
Menu Navigation Buttons
Use the Menu, ↑, ↓, ,buttons to display and navigate
the on-screen menu.
Stereo Headphone Jack
The 1/8” Headphone jack on monitor’s side takes two
channels of embedded (or analog) audio and provides audio
to connected headphones.
Tally LED
The Tally LED is illuminated, either Green, Red or Yellow, by
connecting the appropriate pin on the tally connector to
Ground.

7
Rear Panel Features
Power Connector (XLR)
Insert the included XLR Power Supply end here. Power can be
supplied from the included power supply or from a variety of
DC sources supplying the appropriate voltage.
Power Connector (Coax)
Additional connector for Coaxial Power Supplies. Insert the
coax end here, and tighten the locking nut for additional
protection from the cord being accidentally unplugged. If
using a third party power supply, it should have a 5.5mm OD x
2.0mm ID.
HDMI Input
The V-LCD70-AFHD has one HDMI input that is HDCP
compliant. See Compatible Input Formats for details on
accepted formats.
Component (YPbPr) Input / Output
The V-LCD70-AFHD has one Component video input and one
loop through output.
Composite (Video) Input / Output
The V-LCD70-AFHD has one Composite video input and one
loop through ouput.
Stereo Audio Output
The V-LCD70-AFHD has Left and Right Analog outputs. Access
these via the RCA connector inputs.
SDI (3G/SDI) Input / Output
The V-LCD70-AFHD has one SDI input (up to 3G SDI formats)
and one loop through output.
Tally connector
Use the Tally connector, with associated pinout diagram, to
illuminate the front Tally LED.
USB Program
The USB Program connector is for Upgrade and Factory use
only. Do NOT plug a USB cable into this connector without
first calling Marshall Electronics.

8
Compatible Input Formats
Composite (Video)
NTSC
PAL
Component (YPbPr)
720p/50, 59.94, 60
1080p/23.98, 24, 25, 29.97, 30
1080i/50,59.94,60
HDMI
720p/50,59.94,60
1080p/23.98, 24, 25, 29.97, 30
1080i/50,59.94,60
1080p/50,59.94,60
3G-SDI
480i, 576i
720p/50,59.94,60
1080p/23.98, 24, 25, 29.97, 30
1080i/50,59.94,60
1080p/50,59.94,60 (3G Level A)

9
MAIN MENU AND NAVIGATION
Access and navigate the main menu using the Menu button on the keypad:
Using the Menu buttons
• Press the MENU button to enter the main menu.
• Use the and buttons to scroll through the main menu or each submenu.
• Press the and button to enter a submenu or choose a setting.
• Press the MENU button to exit the main menu, or return to the main menu from a submenu.
Picture Submenu
Contrast (0-100, 50 = default)
Brightness (0-100, 50 = default)
Saturation (0-100, 50 = default)
Tint (0-100, 50 = default)
Sharpness (0-100, 0 = default)
Color Temp (6500K = default)
6500K
7300K
9300K
User (0-255, 128 = Default)
Color TempR

10
Color TempG
Color TempB
Picture Mode
Standard (Contrast, Brightness, Saturation and Tint = 50)
Soft (Contrast = 40, Brightness, Saturation = 45)
User (User Defined settings)
Vivid (Contrast = 60, Brightness = 55, Saturation = 75)
Aspect Ratio
Full Screen (Image is scaled across the entire screen)
4:3 (Image is displayed in a 4:3 aspect ratio)
16:9 (Image is displayed in a 16:9 aspect ratio)
14:9 (Image is displayed in a 14:9 aspect ratio)
Zoom1 (Scale 45% of the image across the entire screen)
Zoom2 (Scale 50% of the image across the entire screen)
Video & Audio Submenu
Peaking (Superimpose red highlight over parts of the image that are in focus)
Mode1 (red highlight over parts of the image in focus)
Mode2 (red highlight over parts of the monochrome image in focus)
False Colors (Adds visual filtering to determine IRE levels in the image according to the chart below)
Exposure (Adds red-striped overlay to areas of the image that may be overexposed)
Histogram (Display a histogram on the bottom right corner of the display)
Squared Segmentation (OFF = default)
Screen Markers (OFF = Default)
OFF
96%
93%
90%
85%
80%
Center Marker (Places cross-hairs at the center of the display)
Check Field
OFF (Contrast, Brightness, Saturation and Tint = 50)
Mono (Images displayed in monochrome)
Red (Only red colors in image are seen)
Green (Only green colors in image are seen)
Blue (Only blue colors in image are seen)
H/V Delay (Picture is shifted horizontally and vertically to check for ancillary data, HANC and VANC in SDI
signals)
Scan Mode