Marshall Electronics V-MD1012 User manual

V-MD1012
Dual 10.1” Rack Mount Monitor with Modular Input / Output
User Manual

V-MD1012
2User Manual v1.0
Table of Contents
1. Introduction, Installation and Setup.........................................................................................................3
2. Product Overview & Features.................................................................................................................4
3. Dimensions ............................................................................................................................................8
4. Navigation Menu ....................................................................................................................................9
4.1 Scaling Configuration Submenu...................................................................................................9
4.2 Color Configuration Submenu....................................................................................................11
4.3 Markers Configuration Submenu................................................................................................13
4.4 Filter Configuration Submenu.....................................................................................................14
4.5 Audio Configuration Submenu....................................................................................................17
4.6 Signal Analysis Configuration Submenu.....................................................................................17
4.7 User Settings Configuration Submenu .......................................................................................18
4.8 System Configuration Submenu.................................................................................................19
5. Monitor Care ........................................................................................................................................21
6. Warranty...............................................................................................................................................21
IMPORTANT SAFETY INSTRUCTIONS:
The V-MD1012 Dual Monitor with HDMI I/O and MD Slots has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all electronic
equipment, this unit should be used with care. Please read and follow the safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.
• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where explained in this manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
• Use only the power adapter and power cords and connection cables designed for this unit.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

V-MD1012
3User Manual v1.0
1. Introduction, Installation and Setup
Introduction
The V-MD1012 is a dual 10.1” rack mount monitor with modular slots and HDMI I/O. This monitor offers a high resolution 1920 x
1200 LED backlit panel. Standard features include markers, 4 user-configurable front panel function buttons, RGB gain and bias
control.
Installation
This monitor can be mounted with any standard 19” equipment rack. The attached rack ears can be angled to provide the user
control overthe viewing angle. Adequate ventilation is required when installed to prevent possible damage to the monitor’s internal
components.
Package Contents
Carefully unpack the V-MD1012 monitor and verify that the following items are included:
• 1x - V-MD1012 Dual 10.1” Monitor
• 1x – 12V Power Supply
Connections, Power-On and Initial Setup
Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the power connector to the back of the monitor.
Connect the required cables for video signal input and output. (Power must be applied to the V-MD1012 to activate the loop-
though output.) The monitor defaults to ‘ON’ when power is supplied. Video is automatically detected and displayed on the screen.

V-MD1012
4User Manual v1.0
2. Product Overview & Features
Top and Front Panel Features
1. Power Button
The Power Button will turn the Display ON and OFF. The LED button will dim when the power is ON. The LED is at full power in
the OFF state.
2. Input Select Button
Use the Input Select Button to select between the On-Board HDMI Input or the Module Input (when available).
3. User-Definable Function Buttons
Four user-definable function buttons can beused for direct access to various settings. Functions are assigned using the onscreen
menu or by highlighting a function and selecting that function button.
4. Menu Navigation Buttons
Use the Menu, ↑, ↓, and Select buttons to display and navigate the on-screen menu. See MAIN MENU AND NAVIGATION for
details on using the Menu.
5. Image Adjustment Knobs
Use the Image Adjustment Knobs to adjust image color saturation, brightness and contrast. The status of each adjustment is
shown on the bottom left screen, with values ranging from 0 to 100. Pressing a knob once displays the current value. Pressing a
knob twice resets the value to the default settings.
6. User Control Knob
The User Control Knob can be customized to control multiple functions. Functions can be changed in the main menu.
7. Stereo Headphone Jack
The 1/8” Headphone Jack can receive two channels of embedded HDMI or SDI Audio and will provide an Audio Signal.

V-MD1012
5User Manual v1.0
Rear Panel Features
1. Power Connector
Insert the included Power Supply Coax Cable. Optional DC sources supplying the appropriate voltage can be used as well.
2. HDMI Input and Output
The V-MD1012 has 2 HDMI Inputs and 2 Active Loop-Through Outputs. The HDMI Output is HDCP Compliant and will NOT
pass through HDCP protected content.
3. Module Slot
Use the Module Slot to install any of the compatible MD Series Modules. This functions as a second video input or output.
4. Upgrade Port
Use for upgrade / debugging purposes ONLY. Please contact Marshall Electronics before attempting to use this port.

V-MD1012
6User Manual v1.0
Specifications
Model Name
V-MD1012
Description
Dual 10.1” Rack Monitor
Panel
• Screen Size: Dual 10.1” Diagonal
• Backlight Feature: WLED
• Resolution: 1920x1200
• Contrast Ratio: 800:1
• Luminance: 800 cd/m2
• Contrast Ratio: 800:1
• Display Colors: 16.7M (8-Bit)
• Signal Interface: 8-Bit
• Viewing Angle: 85/85/85/85 (R/L/U/D)
Power Consumption
• Power Input: 12VDC
• Wattage: 30W
• No Over Voltage Protection
• No Reverse Polarity Protection
Loop-Through
• Yes
Cable Lengths
• SDI 300m/ HD 200m/ 3G 100m
Thermal Operating and Storage Temperature
• Operating Temp: 10C – 40C
• Storage Temp: 0C – 40C
Dimensions
• Vertical Hole Spacing: Pass (3RU)
• Horizontal Spacing: Pass (18.31”)
• Rack Opening: Pass (17.7”)
Tally Pinout
1 Screen
• Pin 1– Green
• Pin 2 – Red
• Pin 3 – Yellow
• Pin 4 – Ground
• Pin 5 – No Contact
Screen 2
• Pin 11 – Green
• Pin 12 – Red
• Pin 13 – Yellow
• Pin 14 – Ground
Module and Format Compatibility
MD-3GE (Modular)
• 480i 59.94Hz
• 576i 50Hz
• 720p 25Hz
• 720p 29.97Hz
• 720p 30Hz
• 720p 50Hz
• 720p 59.94Hz
• 720p 60Hz
• 1080psf 23.98Hz
• 1080psf 24Hz
• 1080p 23.98Hz
• 1080p 24z
• 1080p 29.97Hz
• 1080i 50Hz
• 1080i 60Hz
• 3G – Level A 1080p 50Hz
• 3G – Level A 1080p 59.94Hz
• 3G – Level A 1080p 60Hz

V-MD1012
7User Manual v1.0
MDO-3G (Modular)
• 720p 50Hz
• 720p 59.94Hz
• 720p 60Hz
• 1080p 23.98Hz
• 1080p 24Hz
• 1080p 25Hz
• 1080p 29.97Hz
• 1080p 30Hz
• 1080i 50Hz
• 1080i 59.94Hz
• 1080i 60Hz
• 3G – Level A 1080p 50Hz
• 3G – Level A 1080p 59.94Hz
• 3G – Level A 1080p 60Hz
*MDO-3G module output is converted from HDMI input. HDCP protected will not be looped through.
HDMI Input (Board)
• 480p 59.94Hz
• 576p 50Hz
• 720p 25Hz
• 720p 29.97Hz
• 720p 30Hz
• 720p 50Hz
• 720p 59.94Hz
• 720p 60Hz
• 1080psf 23.98Hz
• 1080psf 24Hz
• 1080p 23.98Hz
• 1080p 24Hz
• 1080p 25Hz
• 1080p 29.97Hz
• 1080p 30Hz
• 1080i 50Hz
• 3G – Level A 1080p 50Hz
• 3G – Level A 1080p 59.94Hz
• 3G – Level A 1080p 60Hz

V-MD1012
8User Manual v1.0
3. Dimensions
Dimensions

V-MD1012
9User Manual v1.0
4. Navigation Menu
Main Menu:
Push the 4 Menu Buttons or the Marshall Electronics RotoMenu™ Knob (integrated into the BRIGHT knob) to adjust the function
configurations. To change configurations, select a configuration from the main menu by turning the knob and pressing the menu
button once to select. Edit configuration by turning knob to change levels, then press menu button again to confirm the changes.
Repeat with each selection as needed. By default, the menu automatically times out after 15 seconds of being idle.
4.1 Scaling Configuration Submenu
ITEMS
OPTIONS
Scaling Configuration
Input Crop
Off, On
Aspect Ratio
Auto, Full Screen, 4:3, 16:9, Custom
Pixel-to-Pixel
Off, On
DSLR Preset
Off, NK 16:9, NK 3:2, CN 16:9
Use the Scaling Submenu to adjust how the video signal is displayed on each screen.
Input Crop
Enable the Input Crop function to select the area of active video that you would like shown on the image display. Select the
area by accessing the Adjust Function.
Input Crop Adjust
Use the BRIGHT knob to move the selection box LEFT and RIGHT.
Use the COLOR knob to move the selection box UP and DOWN.
Use the CONTRAST knob to move the right border LEFT and RIGHT.
Use the USER knob to move the bottom border UP and DOWN.
When satisfied with the position, press the SELECT button or press the BRIGHT knob to confirm selection.

V-MD1012
10 User Manual v1.0
The new cropped selection will be displayed on the screen. If Aspect Ratio is set to AUTO, the monitor will select the closest
aspect ratio to the dimensions of the customized Input.
Aspect Ratio
Use this menu option to switch between several aspect ratio settings.
• In 4:3 Mode, images are scaled up or down to fill the maximum 4:3 portion of the screen.
• In 16:9 Mode, images are scaled to fill the entire 16:9 screen.
• In Full Screen, images are scaled to fill the entire screen.
• In Custom Mode, use the adjust function to customize the image scaling.
Aspect Ratio Adjust
Use any of the rotary knobs to select your desired aspect ratio. Standard aspect ratio settings are shown on the Aspect Ratio
selection widget. Move along the scale and the current aspect ratio will be displayed below the widget.
Pixel-to-Pixel
Use this setting to enable the Pixel-to-Pixel Mode.
This mode bypasses the monitor’s internal scaling function and displays images in their native resolution and aspect ratio,
with a one-to-one mapping of incoming image pixels to screen pixels:
• For incoming formats smaller than the native resolution of the screen (or selected aspect ratio), the image will be
displayed in the center of the screen using only the necessary LCD pixels. For example, 720p images will display
exactly 1280x720 pixels in the center of the screen. The surrounding screen area will be black.
Use the Adjust Function to customize the Pixel to Pixel zone.