Martec MR0124 User manual

ROCKET
SERIES
Ceiling Fan Instrucon Book
Models: MR0124 MRO1244
DESCRIPTION QUANTITY
Motor assembly 1
Instrucon manual 1
Screw kit 1
Balancing kit 1
Hanging bracket 1
Wall control kit 1

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 2
IMPORTANT
Always operate the product from a power source of the same Voltage, Frequency and rangas on the
product Idencaon Plate.
IMPORTANT
The fan is to be installed so that the blades are more than 2.1 metres above the oor.
Avoid contacng moving parts, keep hands, hair and clothing well away from the product while it is in
operaon.
A Luminaire (light ng) included in the fan packaging may only be ed to this fan.
“This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilies, or lack of experience or knowledge, unless they have been given supervision or
instrucon concerning use of the appliance by a person responsible for their safety.”
“Young children should be supervised at all mes to ensure that they do not play with the appliance.”
Do not operate any product which has been or appears damaged in any maer or aer the product
malfuncons.
Do not use the product for other than its intended use as described in these instrucons. This product
is intended for normal domesc household use only. The use of accessory aachments other than those
recommended by the manufacturer may cause safety hazards.
SAFETY
The installaon of fans must follow S.A.A. standards and meet local Authority regulaons. A fully qualied
and licensed electrician lawfully MUST carry out installaon. Means for disconnecon must be incorporated
in the xed wiring in accordance with wiring rules. Fan and light MUST be earthed. Bracket MUST be rmly
aached to a solid structure i.e. concrete ceiling, steel structure or mber frame, etc. and MUST be nailed
between beams if the mber opon is required. ONLY install the remote controller kit that comes supplied
by Martec Pty Ltd within package. DO NOT control operaon of fan and light with any other remote control
than what was approved by Martec Pty Ltd and supplied within this package, as this will void warranty.
WARNING
Only approved Martec Pty Ltd wall controllers should be used for the operaon of our fans. The use of
unauthorised controllers will void the warranty. DO NOT mix blades from one fan to another. All blades
must be replaced if damaged.
Thank you for purchasing your MARTEC ROCKET Series Ceiling Fan. Please read all instrucons carefully
before assembly and use.
IMPORTANT SAFEGUARDS
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. KEEP
THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT INSTALL THE PRODUCT WHERE IT
CAN BE EXPOSED TO RAIN, MOISTURE OR ANY LIQUID.

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 3
With Light
Without Light
Hanging Bracket
Cover
Hanging Ball
Down Rod
Canopy
Wall Control
Blade
Housing
Light Plate
Glass
Hanging Bracket
Reverse Switch
Motor
Housing
Cover
Hanging Ball
Down Rod
Canopy
Wall Control
Blade

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 4
HOW TO ASSEMBLE
Secure the hanger bracket to ceiling beam or a suitable piece of mber inserted between the ceiling beams.
Martec Pty Ltd recommends the bracket to be aached with two long screws as supplied within the package.
There is a ball seat rubber cover need to be pressed into the bracket.(See Fig.1.)
Place circular shockproof gasket above the hanger bracket. Align the bracket and screw the hanger bracket to
the ceiling ghtly.(See Fig.2.)
Place fan into hanger bracket and align Ball Joint Slot with hanger bracket as illustrated.(See Fig.3.)
Aer wiring is completed, aach the canopy to the hanger bracket by pushing upwards and twisng an
clockwise. Locate screws in keyholes and ghten., ensuring canopy is not touching the ball joint. (See Fig.4)
HOW TO INSTALL BLADES
Aach the blade to the top of the motor with two blade screws and washers provided. Tighten them
securely.
Repeat this procedure for all blades. (See Fig.4a. or Fig. 4b)
Fig.3 Fig.4
Fig.2Fig.1
ball seat rubber cover
(Packed with hanger bracket)
Fig.4bFig.4a
Without light With light

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 5
USE IN ALL SEASONS
Always ensure fan is set to ‘OFF’ and blades are sll, prior to changing direcon of blades.
Reverse switch on fan should ideally be set on ‘FORWARD’ (down posion) during warmer season to move
blades in a clockwise direcon & ‘REVERSE’ (up posion) during cooler seasons to make the fan rotate in an
anclockwise direcon (See Fig.5)
HOW TO REMOVE THE SHADE (Version with Light)
Remove the Lamp Shade carefully as shown (See Fig.7). Turn anclockwise to remove
and clockwise to ghten the lampshade.
Only 2 x 15W (MAX) CFL bulbs shall be used. Insert the CFL bulb in the holder
(See Fig.8). Always use a pair of gloves or keep your hands clean when installing or replacing CFL bulbs.
Keeping the globe clean is important and the lifeme of a dirty globe may be shorter than a cleaner globe.
CAUTION: Make sure the power to the fan is not on when inserng light globes (globes not included with
the fan).
Fig.5

www.martecaustralia.com.au | 02 8778 7500 | [email protected]om.au
Page 6
WIRING INSTRUCTIONS