Martec DISCOVERY II AC Series User manual

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
DISCOVERY II AC Series Installation Guide
Thanks for choosing our Discovery II AC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MDF124W 1220mm 4 Blade Ceiling Fan White Satin
MDF124M 1220mm 4 Blade Ceiling Fan Matt Black
MDF134W 1320mm 4 Blade Ceiling Fan White Satin
MDF134M 1320mm 4 Blade Ceiling Fan Matt Black
MDF144W 1420mm 4 Blade Ceiling Fan White Satin
MDF144M 1420mm 4 Blade Ceiling Fan Matt Black
Models Parameters (Fan and LED Light):-
MDF1243W 1220mm 4 Blade Ceiling Fan White Satin with 15w LED Light
MDF1243M 1220mm 4 Blade Ceiling Fan Matt Black with 15w LED Light
MDF1343W 1320mm 4 Blade Ceiling Fan White Satin with 15w LED Light
MDF1343M 1320mm 4 Blade Ceiling Fan Matt Black with 15w LED Light
MDF1443W 1420mm 4 Blade Ceiling Fan White Satin with 15w LED Light
MDF1443M 1420mm 4 Blade Ceiling Fan Matt Black with 15w LED Light
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit Qty 1x balancing kit
Qty 1x hanging bracket Qty 1x wall control kit Qty 4x blades
Application
Flat Surface / Ceiling Slope Ceiling up to 15° Corrugated Ceiling Apex Ceiling
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
Place circular shockproof
gasket above the hanger
bracket. Align the bracket and
screw the hanger bracket to
the ceiling tightly.
Place fan into hanger bracket
and align Ball Joint Slot with
hanger bracket as illustrated.
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting
anti-clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
Fg.1 Fg.2 Fg.3 Fg.4

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
NB: Ensure the blades do not get damaged or bent during the installation process while the fan maybe on the ground, this
will aect the performance and balance of the fan and this is NOT covered under warranty.
The side of the blade marks with “THIS SIDE UP” should be facing upward.
1. Align holes on the blades with holes at the bottom of the motor.
2. Insert the blade and secure with screw.
3. Repeat the same step until all blades are installed.
CCT (Colour Changeable Temperature)
Choose colour temperature by icking the switch in the LED
C = 5000K cool white
N = 4000K neutral white
W = 3000K warm white
Fg.7
Fg.5
How to Install / Remove the Cover
Place the cover plate and screw the tooth
hole of the cover plate to the motor shaft.
Fg.8
Turn anti-clockwise to remove and clockwise to
tighten.
Fg.9Fan only model Fan LED Light Model
How to Install Light Plate
Align the convex point on the light plate with the gap
on the LED mounting plate and press down rmly.
Fg.6
centre band
blade mounting
palte
LED mounting plate
gap
screw
washer
light plate
LED mounting plate
gap
convex point

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Dimming
The Discovery II ceiling fan has a smart 3 step dimming LED light module which doesn’t require a dimmable remote control or a wall
dimmer. It only requires a normal on/o remote kit (MPREMS) or a normal light wall switch. (Supplied in remote control kit).
Turn the switch on and the light will turn on. Flick the switch on/o within 1 second and the light output will dim down to approx. 50%.
Flick the switch on/o again and the light output will dim down to approximately 15%. The light kit has no memory function, It will turn
on 100% initially.
Setting the code on transmitter
1. Remove battery cover
2. Slide code switches to your choice of ON/OFF position
3. Install battery (supplied)
Martec® remote control for AC Ceiling Fan illustrated below are sold separately.
Installing Receiver Remote Control
Receiver
Installation of transmitter wall mount
holder with two screws.
Optional Accessories
MPREMES
Premier Remote Control
MPLCDS
Premium LCD Remote Control
MWFBT
Smart Remote Control
Setting code on receiver:-
1. Slide code switches on the receiver in the same position
set on the transmitter
AC Power Input
Brown
Blue
N
L
To Fan/Light/neutral
To Fan/Live
To Light/Live
Fan Motor
Blue
Brown
Black
Antenna

E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
NB: Remote Control Fan Only and Fan LED LightNB: Wall control Fan Only NB: Wall control Fan LED Light